CdTe and CdZnTe are promising materials for room temperature semiconductor X-ray and gamma ray detectors. The accumulation of a space charge at deep energy levels due to a band bending at contacts with Schottky barriers and due to trapped photogenerated charge may result in time dependent change of charge collection efficiency in CdTe and CdZnTe detectors known as polarization effect. This thesis is mainly focused on a study of electric field profiles in detectors under dark and high photon flux conditions simulating detector operation using crossed polarizers technique exploiting the electro-optic (Pockels) effect. It also deals with a study of deep levels responsible for the polarization and influence of contact metals on charge accumulation. Several experimental results are supported by theoretical simulations. The measurements were performed on three sets of samples equipped with different contact metals (Au, In) cut from three different n-type CdTe and CdZnTe materials. Energy levels were detected using methods based on the Pockels effect and discharge current measurements. Detailed study of internal electric field profiles has revealed a fundamental influence of near midgap energy levels related to crystal defects and contact metals on the polarization in semiconductor detectors under high radiation...

Weirs belong to the basic water structures mainly creating vertical contraction of stream against the flumes, which creating mainly horizontal contraction of stream. In the case of the flow over weir usually occurs change from subcritical flow over critical with critical depth to supercritical flow, therefore overflow. Weirs with rectangular control section are described rectangular longitudinal and transverse profile and horizontal crest. Can be distinguish three basic inflow directions to weir. The first is frontal inflow, which is the most frequent in practice. The second is lateral inflow used in distribution and consumption objects. The third is lower inflow used as laboratory weirs, weirs with deeply submerged wall, etc. In terms of knowledge of influence listed directions of inflows, currently are not sufficiently researched the cases of frontal inflow with side contraction and lower inflow on all types of weirs. Due to extent of the issue, labour is focused only on frontal inflow over broad-crested weir with side contraction and lower inflow over broad-crested weir without side contraction. The goal of the labour was to summarize the current knowledge of the flow over broad-crested weir with side contraction and lower inflow over broad-crested weir without side contraction, describe the character of the flow at the overflow and on the basis of it determine recommendations for measurement and calculation of discharge. Further to define unexplored area, specify methods of solution and verify own measurements. The research dealt with application and optimal numerical model setting for to solve the problem.

The proposed work is dealing with control design of pump-tank system as part of broader water-supply network with using of mechatronic approach. The main goal of this work is design of control for regulation of flow, pressure and water level in tank in water-supply network of Vsetin city. This water-supply network consists of various components, such as pumps, pipes, valves, tanks etc. For the purpose of the control design is necessary to create a model of pipe network. The solution of hydraulic analysis is obtained by using the gradient method, which was implemented into the software solution named ADAM. The results of hydraulic analysis are compared with measured values of flow and pressure and difference of these values has to be minimalized by proposed calibration and verification process. The calibration and verification process was implemented in software ADAM. The essence of design control is formulating control problem as optimization problem. Therefore the output of higher control layer is set of procedural rules, which determines for example speed of pumps in time etc. Results were verified by using for this purpose developed computational server (ADAM Server).

This work inkluse measurement principles for measuring liquid level in tanks with a focus on fuel. Are described most frequently used types of liquid level sensors, focusing on fuel. The work inkluse design chosen technical solutions fuel level sensor and its technical implementation, including the technical implementation and verification of its functionality and calibration.

The aim of this diploma thesis is to evaluate the economical measures using own heat and power production using cogeneration units, use of renewable resources to partially cover the consumption of objects, reduction of thermal losses by evaporation in the outdoor swimming pool and overall increase of waste heat utilization by exchanger heat exchangers from flue gas and heat from waste water.

The diploma thesis deals with the problems of the indoor environment of swimming pool halls. Firstly, it describes issues and principles of designing HVAC system in the areas with high humidity production. Thesis then focuses on various approaches to calculations of evaporation from the water surface and different possibilities of dehumidification including different types of HVAC units. This knowledge was applied to the design of HVAC system for particular assigned building, for which are proposed two different solutions. Thesis includes experimental part, its aim is to analyse one specific critical part of the hall. Based on local surveying and long-term measurements a few possibilities of improvement are suggested.

My diploma thesis deals with the issue revitalization of a small stream. Assessment and design of revitalization is done on Kuřimka stream which flows through the cadastral territory of the Moravian Knínice - Chudčice - Kníničky. In the diploma thesis were designed several of revitalization measures: stabilization of longitudinal tilt with the use of stone steps in the bottom and wooden thresholds, sedimentation reservoir for capturing sediment and slope stabilization using willow fences and gabions. Proposal of revitalization measures does not deteriorate runoff conditions.

This master thesis is dedicated to system of water monitoring for use of alternative source power supply and GSM communication. The thesis carried out research on the possibilities to take measurements on watercourses, also detailed research of photovoltaic panel, available accumulators and their charging and a synopsis of similar systems. Furthermore, the master thesis also captures design and implementation datalogger device type with possibility to send measured data to the website.