No description available.

The influence of plasticization and other formulation factors on the properties of hot-melt extruded dosage forms for the controlled release of water-soluble active compounds was investigated. Citric acid monohydrate was demonstrated to function as a solid-state plasticizer in hot-melt extruded Eudragit® RS PO tablets and in cast films when concentrations below the compatibility limit were employed. Melting of the organic acid and solubilization in the polymer during extrusion were necessary to observe the plasticizing effect. The release rate of diltiazem hydrochloride, used as a high-melting, water-soluble model drug, from melt extruded Eudragit® RS PO matrix tablets increased and became independent of the original drug particle size in the presence of citric acid monohydrate. Thermal analysis of physical mixtures demonstrated that citric acid promoted drug melting during extrusion by interaction and melting point depression. Diltiazem hydrochloride remained amorphous in the final dosage form, and leaching of citric acid monohydrate enhanced drug diffusion by increasing the matrix porosity. Delayed-release matrix pellets with particle sizes below one mm were prepared by hot-melt extrusion, and the influence of the matrix forming polymer and the type and level of plasticizer on the processibility and release properties was investigated. Pellets complied with the USP requirement for delayed release articles to release less than 10% drug at pH 1.2 after 2 hours when plasticized Eudragit® S100 was used as the release-controlling material. High levels of efficient plasticizers had to be employed to decrease the polymeric melt viscosity, increase the process yield and enable extrusion at moderate temperatures to avoid instabilities during processing and storage. The aqueous solubility of the plasticizer further impacted the drug release rate in acid. A novel application of hot-melt extrusion for the preparation of monolithic matrices comprising enteric coated particles was studied. The influence of the mechanical strength of the multiparticulates, pellet loading and nature of the hydrophilic carrier material on the preservation of the delayed-release properties after extrusion was investigated. Soft particles coated with brittle films remained intact when low-melting carriers that did not solubilize the enteric film during extrusion were used, and the dissolution profile was stable over one year. / text

O flubendazol (FB) é um agente anti-helmíntico benzimidazólico cuja potencialidade foi demonstrada para uso no tratamento da filariose linfática e da oncocercose em humanos. As formulações atualmente comercializadas, entretanto, atuam apenas em parasitas do trato gastrointestinal, uma vez que, praticamente, não são absorvidas por via oral em decorrência da baixa solubilidade do fármaco. Assim, observa-se a necessidade da busca de alternativas que melhorem a solubilidade do FB e viabilizem o desenvolvimento de formulações orais de efeito sistêmico. Uma das tecnologias que vem se destacando no mercado farmacêutico nas últimas décadas para a produção de dispersões sólidas amorfas para melhoria de solubilidade é a extrusão a quente; esta representa uma potencial solução para o problema apresentado, constituindo-se o objeto de estudo do presente trabalho. Para tal, foram selecionados os polímeros copovidona e HPMCAS LG, além dos adjuvantes HPC EF e estearato de magnésio. Inicialmente os componentes individuais e misturas binárias de FB e excipientes foram caracterizados por DSC e TG, mostrando-se compatíveis com o fármaco em questão. Misturas entre o fármaco, polímero e adjuvantes para a extrusão a quente foram planejadas por delineamento experimental e o processo conduzido em extrusora dupla rosca. Parâmetros como a temperatura das zonas de aquecimento, velocidade de alimentação e das roscas da extrusora foram mantidos constantes durante todo o processo, de modo a avaliar o impacto de cada material e sua porcentagem na fórmula. A copovidona mostrou-se altamente extrusável, sendo que o HPMCAS LG, para os parâmetros utilizados, não permitiu a obtenção de extrusados com o FB. Todos os testes feitos com a copovidona, exceto o com alta carga de FB, pois nesta condição não foi possível obter extrusados, foram avaliados por meio de DSC e difratometria de raios-X pelo método do pó, durante um ano em temperatura ambiente e, após 30 dias, em condição de estabilidade acelerada (40°C/75% U.R.), com resultados positivos relativos à amorfização do fármaco. Adicionalmente, ensaios de dissolução foram realizados em meio HCl pH 1.2 indicaram melhoria expressiva da solubilidade, porém de forma distinta para cada formulação proposta. Desta forma, o processo de extrusão a quente com a copovidona mostrou-se uma alternativa viável e eficiente para promover o aumento da dissolução do FB, por meio da obtenção de uma dispersão sólida amorfa estável. / Flubendazole (FB) is a benzimidazole anthelmintic agent that has recently demonstrated effectiveness for the treatment of lymphatic filariasis and onchocerciasis in humans. However, the formulations currently commercialized act only on parasites of the gastrointestinal tract, since they are not orally absorbed due to the poor drug solubility. Thus, there is a need to seek alternatives to improve FB solubility and enable the development of oral formulations with systemic effect. Hot melt extrusion (HME) is a technology that has been outstanding on the pharmaceutical market in recent decades aiming to produce amorphous solid dispersion for solubility enhancement. Aside from that, this technique can be considered a potential alternative to the presented drug. Therefore, the purpose of this study was to prepare a solid dispersion using copovidone and HPMCAS LG as the polymers and HPC EF and magnesium stearate as the adjuvants. Initially, the individual components and drug/excipients binary mixtures were characterized by differential scanning calorimetry (DSC) and thermogravimetry (DTG) to evaluate the thermal behavior and compatibility with FB. Through these tests, it was possible to verify that the polymers and adjuvants chosen were compatible with FB. Then, the mixtures of drug, polymer and adjuvant were designed statistically and the process was performed in a twin-screw extruder; the temperature of the heating zones, screw speed, and feed screw speed were kept constant for all tests to evaluate the impact of each material and its percentage on getting an achievable solid dispersion. Copovidone was highly extrudable and the HPMCAS LG, for the determined parameters, did not allow obtaining extrudates for FB. The extruded materials were evaluated by DSC and X-ray powder diffraction and presented positive results concerning amorphization of the drug, except the tests with high drug loading. Stability tests were performed at room temperature for one year and accelerated condition (40° C/75% RH) for 30 days showing, for almost all tests, optimistic results regarding keeping FB amorphous. In order to evaluate the improvement of the solubility of the drug, a comparative dissolution test of the extrudates and the pure FB was carried out at HCl pH 1.2. At different levels, all extrudates showed expressive improvement on the solubility when compared to pure FB. In conclusion, HME process can be considered a viable alternative to obtain stable solid amorphous dispersion of FB and copovidone.

O flubendazol (FB) é um agente anti-helmíntico benzimidazólico cuja potencialidade foi demonstrada para uso no tratamento da filariose linfática e da oncocercose em humanos. As formulações atualmente comercializadas, entretanto, atuam apenas em parasitas do trato gastrointestinal, uma vez que, praticamente, não são absorvidas por via oral em decorrência da baixa solubilidade do fármaco. Assim, observa-se a necessidade da busca de alternativas que melhorem a solubilidade do FB e viabilizem o desenvolvimento de formulações orais de efeito sistêmico. Uma das tecnologias que vem se destacando no mercado farmacêutico nas últimas décadas para a produção de dispersões sólidas amorfas para melhoria de solubilidade é a extrusão a quente; esta representa uma potencial solução para o problema apresentado, constituindo-se o objeto de estudo do presente trabalho. Para tal, foram selecionados os polímeros copovidona e HPMCAS LG, além dos adjuvantes HPC EF e estearato de magnésio. Inicialmente os componentes individuais e misturas binárias de FB e excipientes foram caracterizados por DSC e TG, mostrando-se compatíveis com o fármaco em questão. Misturas entre o fármaco, polímero e adjuvantes para a extrusão a quente foram planejadas por delineamento experimental e o processo conduzido em extrusora dupla rosca. Parâmetros como a temperatura das zonas de aquecimento, velocidade de alimentação e das roscas da extrusora foram mantidos constantes durante todo o processo, de modo a avaliar o impacto de cada material e sua porcentagem na fórmula. A copovidona mostrou-se altamente extrusável, sendo que o HPMCAS LG, para os parâmetros utilizados, não permitiu a obtenção de extrusados com o FB. Todos os testes feitos com a copovidona, exceto o com alta carga de FB, pois nesta condição não foi possível obter extrusados, foram avaliados por meio de DSC e difratometria de raios-X pelo método do pó, durante um ano em temperatura ambiente e, após 30 dias, em condição de estabilidade acelerada (40°C/75% U.R.), com resultados positivos relativos à amorfização do fármaco. Adicionalmente, ensaios de dissolução foram realizados em meio HCl pH 1.2 indicaram melhoria expressiva da solubilidade, porém de forma distinta para cada formulação proposta. Desta forma, o processo de extrusão a quente com a copovidona mostrou-se uma alternativa viável e eficiente para promover o aumento da dissolução do FB, por meio da obtenção de uma dispersão sólida amorfa estável. / Flubendazole (FB) is a benzimidazole anthelmintic agent that has recently demonstrated effectiveness for the treatment of lymphatic filariasis and onchocerciasis in humans. However, the formulations currently commercialized act only on parasites of the gastrointestinal tract, since they are not orally absorbed due to the poor drug solubility. Thus, there is a need to seek alternatives to improve FB solubility and enable the development of oral formulations with systemic effect. Hot melt extrusion (HME) is a technology that has been outstanding on the pharmaceutical market in recent decades aiming to produce amorphous solid dispersion for solubility enhancement. Aside from that, this technique can be considered a potential alternative to the presented drug. Therefore, the purpose of this study was to prepare a solid dispersion using copovidone and HPMCAS LG as the polymers and HPC EF and magnesium stearate as the adjuvants. Initially, the individual components and drug/excipients binary mixtures were characterized by differential scanning calorimetry (DSC) and thermogravimetry (DTG) to evaluate the thermal behavior and compatibility with FB. Through these tests, it was possible to verify that the polymers and adjuvants chosen were compatible with FB. Then, the mixtures of drug, polymer and adjuvant were designed statistically and the process was performed in a twin-screw extruder; the temperature of the heating zones, screw speed, and feed screw speed were kept constant for all tests to evaluate the impact of each material and its percentage on getting an achievable solid dispersion. Copovidone was highly extrudable and the HPMCAS LG, for the determined parameters, did not allow obtaining extrudates for FB. The extruded materials were evaluated by DSC and X-ray powder diffraction and presented positive results concerning amorphization of the drug, except the tests with high drug loading. Stability tests were performed at room temperature for one year and accelerated condition (40° C/75% RH) for 30 days showing, for almost all tests, optimistic results regarding keeping FB amorphous. In order to evaluate the improvement of the solubility of the drug, a comparative dissolution test of the extrudates and the pure FB was carried out at HCl pH 1.2. At different levels, all extrudates showed expressive improvement on the solubility when compared to pure FB. In conclusion, HME process can be considered a viable alternative to obtain stable solid amorphous dispersion of FB and copovidone.

The number of newly developed chemical entities exhibiting poor water solubility has increased dramatically in recent years. In many cases this intrinsic property results in poor or erratic dissolution in biological fluids. Improving aqueous solubility of these compounds, even temporarily, can have a significant impact on in vivo performance. Single phase amorphous solid dispersions of a drug and polymer have emerged as a technique to not only increase the level of drug supersaturation but also maintain these levels for extended periods of time. Hot-melt extrusion (HME) has become the preferred processing technique to prepare systems such as these but has a number of limitations that prevent the successful formulation of many drug substances. Within this dissertation, the use of concentration enhancing polymers was investigated in parallel with a thorough evaluation of a novel fusion-based processing technique, KinetiSol® Dispersing (KSD), to prepare single phase amorphous solid dispersions that could not be successfully prepared by HME. Studies showed that the KSD technique is suitable for rendering thermally labile and high melting point drug substances amorphous through a combination of frictional and shearing energy. Compounds such as these were shown to degrade during HME processing due to relatively long residence times and low shear forces. Similarly, the KSD process was shown to successfully process solid dispersion compositions containing a high viscosity polymer with significantly lower levels of polymer degradation than obtained by HME processing. In the final study, KSD processing was used to prepare solid dispersions containing the hydrophilic polymer Soluplus[superscript TM] and methods were evaluated to formulate a tablet with rapid tablet disintegration characteristics, a requirement for sufficient dissolution enhancement. Combined, the studies demonstrated the effectiveness of combining proper polymer selection and formulation approaches with a suitable processing technique to form solid dispersion systems that provide rapid and extended durations of supersaturation. / text

Formulation intervention, through the application of processing technologies, is a requirement for enabling therapy for the vast majority of drugs. Without these enabling technologies, poorly soluble drugs may not achieve therapeutic concentrations in the blood or tissue of interest. Conversely, freely soluble and/or rapidly cleared drugs may require frequent dosing resulting in highly cyclic tissue concentrations. During the last several years, thermal processing techniques, such as melt mixing, spray congealing, sintering, and hot-melt extrusion (HME), have evolved rapidly. Several new technologies, specifically dry powder coating, injection molding, and KinetiSol® dispersing (KSD), have been adapted to the pharmaceutical arena. Co-rotating twin screw extrusion is routinely applied for the purposes of dissolving poorly soluble drugs into glassy polymers to prepare amorphous solid dispersions, which create supersaturated drug concentrations in the gastro-intestinal tract. A potentially more advantageous alternate geometry, counter-rotating twin screw extrusion was evaluated for preparation of model amorphous solid dispersion and was observed to be more efficient in forming a solid solution and reduced the thermal stress on the drug. HME and KSD processes were utilized to prepare two phase systems consisting of a lipid, glyceryl behenate, and a polymeric amorphous solid dispersion intended to provide both controlled release of drug and supersaturated drug concentrations in the release medium. Such systems are challenging due to the potential for crystallization of the drug within the dosage form during release, which was observed to be influenced by lipophilicity and porosity of the formulation, as well as the surface area to volume ratio of the system. High molecular weight cellulose based glassy dispersions were prepared using a weakly basic model drug by KSD, which when formulated into tablets were optimized to provide either immediate or approximately 2 hours of controlled release under the pH conditions simulating the environment of the stomach. Without formulation intervention in the external phase of the tablet, these compositions gel, muting drug release and missing the drug absorption window. Compositions optimized by an in vitro dissolution test were compared to a lower molecular weight HME prepared commercial product in a beagle dog model and observed to have statistically similar bioavailability, and in one case improved variability. A modified twin screw extrusion machine was utilized to develop a continuous granulation process capable of producing granules that do not require subsequent grinding or sizing. This novel process, which employs previously un-reported temperature profiles, produces lipid based granules that when compressed into tablets produce a controlled release of tramadol hydrochloride, which were not susceptible to alcohol induced dose dumping. / text

Process Analytical Technology (PAT) is framed with the objective of the design and development of processes to ensure predefined quality of the product at the end of manufacturing. PAT implementation includes better understanding of process, reduction in production time with use of in-line, at-line and on-line measurements, yield improvement and energy and cost reductions. Hot Melt Extrusion process (HME) used in the present work is proving increasingly popular in industry for its continuous and green processing which is beneficial over traditional batch processing. The present work was focused on applications of Raman spectroscopy as off - line and in - line monitoring techniques as a PAT for production of pharmaceutical solid dispersions and co-crystals. Solid dispersions (SDs) of the anti-convulsant Carbamazepine (CBZ) with two pharmaceutical grade polymers have been produced using HME at a range of drug loadings and their amorphous nature confirmed using a variety of analytical techniques. Off-line and in-line Raman spectroscopy has been shown to be suitable techniques for proving preparation of these SDs. Through calibration curves generated from chemometric analysis in-line Raman spectroscopy was shown to be more accurate than off-line measurements proving the quantification ability of Raman spectroscopy as well as a PAT tool. Pure co-crystals of Ibuprofen-Nicotinamide and Carbamazepine-Nicotinamide have been produced using solvent evaporation and microwave radiation techniques. Raman spectroscopy proved its superiority over off-line analytical techniques such as DSC, FTIR and XRD for co-crystal purity determination adding to its key advantage in its ability to be used as an in-line, non-destructive technique.

The success of an amorphous solid dispersion (ASD) formulation, consisting of a homogeneous molecular dispersion of drug and polymer, relies on its ability to create and maintain a supersaturated solution. However, supersaturated solutions are metastable and prone to crystallization. In solution, crystals are expected to serve as a template for crystal growth, depleting achieved supersaturation. Thus, in an ASD product, ideally no crystallinity should be present. However, technical challenges exist in both processing and characterization to routinely ensure this is achieved. The presented studies follow the process design, characterization, and dissolution performance of hot melt extruded amorphous solid dispersions, seeking insight into the significance of critical quality attributes of resulting extrudates, namely residual crystallinity and thermal degradation.<div>Selection of hot melt extrusion (HME) processing conditions to prepare ASDs is governed by thermodynamic and kinetic attributes of the drug and polymer system. Mapping the temperature-composition phase diagram to HME processing conditions provides a processing design strategy to prevent residual crystallinity while simultaneously avoiding thermal degradation. Through processing temperatures below the drug’s melting point (Tm) and above the formulation critical temperature (Tc), fully amorphous systems could be generated if sufficient kinetics were provided. The utility of thermogravimetric analysis was critically examined for prediction of the chemical stability processing window for HME formulations.<br></div><div>For characterization and product performance characterization, residual crystalline content in HME ASDs can be anticipated and tailored to various levels. Several HME ASDs were characterized by a range of analytical techniques, highlighting the sensitivity of available techniques to qualitatively or quantitatively detect crystalline content (depending on limitations which stem from properties of the instrument or sample). Transmission electron microscopy (TEM) was found to identify low levels of crystallinity not observed by other technique and provide insight into crystal dissolution mechanisms. A defect-site driven dissolution and fragmentation model was suggested, and supported by a Monte Carlo simulation, underscoring that crystal defect sites, either intrinsic to the crystals or formed during processing, expedite dissolution rates and generation of new surfaces for dissolution.<br></div><div>Non-sink dissolution was performed for indomethacin/PVPVA HME ASD samples with residual crystallinity ranging from 0-25% crystalline content. Due to effective crystal growth inhibition by the polymer, crystals had little impact on dissolution performance. Achieved supersaturation was reduced approximately by the level of crystallinity present, i.e. a lost solubility advantage. These studies have significance for HME processing design and risk assessment of crystallinity within ASD formulations.<br></div>

Ibrutinib is the first Bruton`s tyrosine kinase (BTK) inhibitor for oral administration approved by FDA in 2014. It is the first-line treatment for B-cell malignancies, which are the most common hematologic neoplasia. Ibrutinib is a relatively safe alternative for currently used treatment modalities that are associated with long-term toxicity and resistance. However, ibrutinib is considered as BCS class II drug and has very low solubility in an aqueous medium (13 μg/ml at PH 8.0) and has six different polymorphic forms. Furthermore, recommended daily dose of ibrutinib is about 420 mg to 560 mg, which causes severe GI disturbances, with poor patient compliance. This represent a major critical concern because drug is used chronically. Increasing drug solubility and controlling rate of drug release may improve both bioavailability at significantly lower daily administered doses and by implication could minimize GI side effects and improve patient compliance.The objective of this study is to utilize Hot Melt Extrusion (HME) to develop a stable amorphous solid dispersion (ASD) of ibrutinib using Copovidone (PlasdoneTM S-630 Ultra) as a carrier for inclusion into a hydrating matrix for sustained release delivery. Development of ASD based on HME is an efficient method to overcome poor solubility problem and stabilize the drug`s metastable polymorphic states. It is known that amorphous systems are energetically at a higher thermodynamic state and can dissolve to a much greater extent relative to their crystalline counterpart. A stable sustained-release ASD based system may offer many advantages, including reduction in frequency of administration and GI disturbances with propensity to enhance solubilization while suppressing recrystallization. The ASD systems prepared in this study was stable, amorphous, and single-phase systems up to 60% API load as confirmed by X-ray powder diffraction (XRPD), modulated differential scanning calorimetry (mDSC), and rheological analysis. Supersaturated micro-dissolution testing of melt-extruded powder in fasted state simulated intestinal fluid demonstrated up to 70% increase in supersaturation solubility than the saturation solubility of crystalline counterparts. In addition, dissolution data based on the standard USP paddle method for the formulated SR tablets demonstrated a prolonged release up to six hours and a maximum of 53% higher drug release than crystalline ibrutinib. In conclusion, the results of this study indicate that ibrutinib amorphous solid dispersion developed utilizing hot-melt extrusion technology and Copovidone (PlasdoneTM S-630 Ultra) as a carrier is able to produce stable and homogeneous single-phase ASD system with enhanced solubility and desirable sustained drug release rate. / Pharmaceutical Sciences

Polylactic acid (PLA) resins of various molecular weights and molecular weight distributions were synthesized. Linear, narrow molecular weight distribution (MWD) PLA resins were synthesized, as well as resins containing both high molecular weight branched structures and low molecular weight chains and oligomers. Narrow MWD resins were synthesized for use as adhesives for corrugated paperboard and broad MWD resins were synthesized for use as a waterborne coating. PLA resins were dispersed for use as a waterborne coating. Success has been made at forming films utilizing various plasticizers and surfactants as well as polyvinyl alcohol as dispersing agents. A cold dispersion procedure realized the most success, as a 15% PLA waterborne formulation was achieved. Standard test methods show a high degree of grease resistance for the formulated coatings. A hot melt adhesive was also formulated utilizing blends of narrow MWD resins of various molecular weights. The hot melt adhesive showed a high degree of success as failure occurred at the substrate for the materials tested.