This thesis deals with the description and development of two classical turbulent shear flows, namely free jet and flat plate turbulent boundary layer flows. In both cases new experimental data has been obtained and in the latter case comparisons are also made with data obtained from data bases, both of experimental and numerical origin. The jet flow studies comprise three parts, made in three different experimental facilities, each dealing with a specific aspect of jet flows. The first part is devoted to the effect of swirl on the mixing characteristics of a passive scalar in the near-field region of a moderately swirling jet. Instantaneous streamwise and azimuthal velocity components as well as the temperature were simultaneously accessed by means of combined X-wire and cold-wire anemometry. The results indicate a modification of the turbulence structures to that effect that the swirling jet spreads, mixes and evolves faster compared to its non-swirling counterpart. The high correlation between streamwise velocity and temperature fluctuations as well as the streamwise passive scalar flux are even more enhanced due to the addition of swirl, which in turn shortens the distance and hence time needed to mix the jet with the ambient air. The second jet flow part was set out to test the hypothesis put forward by Talamelli & Gavarini (Flow, Turbul. & Combust. 76), who proposed that the wake behind a separation wall between two streams of a coaxial jet creates the condition for an absolute instability. The experiments confirm the hypothesis and show that the instability, by means of the induced vortex shedding, provides a continuous forcing mechanism for the control of the flow field. The potential of this passive mechanism as an easy, effective and practical way to control the near-field of interacting shear layers as well as its effect towards increased turbulence activity has been shown. The third part of the jet flow studies deals with the hypothesis that so called oblique transition may play a role in the breakdown to turbulence for an axisymmetric jet.For wall bounded flows oblique transition gives rise to steady streamwise streaks that break down to turbulence, as for instance documented by Elofsson & Alfredsson (J. Fluid Mech. 358). The scenario of oblique transition has so far not been considered for jet flows and the aim was to study the effect of two oblique modes on the transition scenario as well as on the flow dynamics. For certain frequencies the turbulence intensity was surprisingly found to be reduced, however it was not possible to detect the presence of streamwise streaks. This aspect must be furher investigated in the future in order to understand the connection between the turbulence reduction and the azimuthal forcing. The boundary layer part of the thesis is also threefold, and uses both new data as well as data from various data bases to investigate the effect of certain limitations of hot-wire measurements near the wall on the mean velocity but also on the fluctuating streamwise velocity component. In the first part a new set of experimental data from a zero pressure-gradient turbulent boundary layer, supplemented by direct and independent skin friction measurements, are presented. The Reynolds number range of the data is between 2300 and 18700 when based on the free stream velocity and the momentum loss thickness. Data both for the mean and fluctuating streamwise velocity component are presented. The data are validated against the composite profile by Chauhan et al. (Fluid Dyn. Res. 41) and are found to fulfil recently established equilibrium criteria. The problem of accurately locating the wall position of a hot-wire probe and the errors this can result in is thoroughly discussed in part 2 of the boundary layer study. It is shown that the expanded law of the wall to forth and fifth order with calibration constants determined from recent high Reynolds number DNS can be used to fix the wall position to an accuracy of 0.1 and 0.25 l_ * (l_* is the viscous length scale) when accurately determined measurements reaching y+=5 and 10, respectively, are available. In the absence of data below the above given limits, commonly employed analytical functions and their log law constants, have been found to affect the the determination of wall position to a high degree. It has been shown, that near-wall measurements below y+=10 or preferable 5 are essential in order to ensure a correctly measured or deduced absolute wall position. A  number of peculiarities in concurrent wall-bounded turbulent flow studies, was found to be associated with a erroneously deduced wall position. The effect of poor spatial resolution using hot-wire anemometry on the measurements of the streamwise velocity is dealt with in the last part. The viscous scaled hot-wire length, L+, has been found to exert a strong impact on the probability density distribution (pdf) of the streamwise velocity, and hence its higher order moments, over the entire buffer region and also the lower region of the log region. For varying Reynolds numbers spatial resolution effects act against the trend imposed by the Reynolds number. A systematic reduction of the mean velocity with increasing L+ over the entire classical buffer region and beyond has been found. A reduction of around 0.3 uƬ, where uƬ is the friction velocity, has been deduced for L+=60 compared to L+=15. Neglecting this effect can lead to a seemingly Reynolds number dependent  buffer or log region. This should be taken into consideration, for instance, in the debate, regarding the prevailing influence of viscosity above the buffer region at high Reynolds numbers. We also conclude that the debate concerning the universality of the pdf within the overlap region has been artificially complicated due to the ignorance of spatial resolution effects beyond the classical buffer region on the velocity fluctuations. / QC 20100820

Les instabilités aéroélastiques de bandes d’acier constituent aujourd’hui l’un des problèmes majeurs dans les sections de refroidissement par jets impactants des lignes de recuit continues.En effet, le traitement thermique des nouveaux aciers nécessite de très fortes pentes de température impliquant constamment des augmentations de vitesse de soufflage susceptibles de mettre en jeu des instabilités aéroélastiques. Des flottements ainsi que des divergences de bande ont déjà été constatées et identifiées. Ces deux instabilités impliquent dans la plupart des cas des chocs entre la bande et les buses de soufflage ce qui engendre des défauts de surface sur la bande.Un banc d’essai a été conçu et fabriqué dans le but d’analyser ces instabilités et d’anticiper leur apparition. A partir d’observations, la dynamique structurelle de la bande a été simplifiée à un mode de rotation rigide. Le banc comporte une plaque oscillante en mouvement forcé.Celle-ci est impactée par un dispositif de plusieurs jets axisymétriques turbulents ayant une disposition identique à celle des tours industrielles. Les efforts aérodynamiques stationnaires et instationnaires agissant sur la plaque sont mesurés au moyen de capteurs de pression.L’impact de plusieurs jets en interaction crée de très importants gradients de pression sur la plaque il est donc nécessaire que la grille de prises de pression soit très fine pour que l’estimation des efforts aérodynamiques soit correcte. La plaque est donc instrumentée de 91capteurs de pression sur une surface de 18 cm². Elle peut également être translatée dans les ois directions de l’espace, ce qui permet d’obtenir la distribution des efforts instationnaires ainsi que des coefficients aéroélastiques sur une grande surface de plaque et à différentes distances d’impact.Les mesures de pression stationnaires ont permis d’établir les courbes d’évolution des efforts d’impact des jets sur la plaque en fonction de la distance jet-plaque ainsi que de la géométrie des buses. Les résultats ont permis de déterminer la stabilité statique de la plaque en mouvement de pompage. Les mesures de vitesses des jets libres ont été effectuées paranémométrie à fil chaud et ont permis de déterminer leurs propriétés statistiques.Les mesures de coefficients aéroélastiques sur la plaque en rotation ont été effectuées surune seule géométrie de soufflage, pour différentes vitesses réduites. Les résultats mettent en évidence l’importance des effets de bords sur la stabilité de plaque. Des méthodes de post traitements ont proposées afin d’extrapoler les résultats à différentes largeurs de bande. Ils sont confrontés aux travaux de Regardin et al. (réf. [1]) et mettent en évidence des désaccords avec le cas réel. Des suggestions sont apportées afin d’améliorer la représentativité du banc vis-à-vis des bandes industrielles. / Aeroelastic instabilities of steel strips impinged by arrays of cooling gas jets have becomeone of the main issues in cooling sections of continuous annealing lines. Indeed, the new steeltreatments require very high temperature variation rates which involve increases in jetvelocities that are likely to onset some aeroelastic instabilities. Strip flutter and divergencehave already been observed and identified. These two aeroelastic instabilities imply a strongrisk of contact with the blowing boxes, which can seriously blemish the strip.An experimental test rig was designed and built in order to analyze and predict of theseinstabilities. From observations, the strip’s structural dynamics was simulated by a rigidrotation mode. The rig included a forced oscillating plate which is impinged by an array ofaxisymmetric jets having the exact industrial geometry. The plate was instrumented withpressure sensors to measure the steady and unsteady surface pressures. The impingement ofinteracting jets creates very large pressure gradients on the plate and therefore a tight mesh ofpressure taps (91 over an 18cm² jet impingement surface) was necessary to allow a goodestimation of the aerodynamic loads The plate could also be moved in the three coordinatedirections as to obtain surface mappings of the unsteady jet forces and aeroelastic coefficientscan be obtained over a wide area and different jet-to-plate distances.The variation of the impinging aerodynamic forces was established as a function of the jetto-plate distance for different nozzle geometries. These results were used to determine the jetstatic stability in plunging motion. Velocity and turbulence measurements in free jets werecarried out using hot wire anemometry in order to determine their statistical properties.Aeroelastic coefficient measurements were carried out on the oscillating plate with onlyone nozzle geometry and different reduced velocities. Results show that the plate’s stability ismainly dependent on the boundary effects. Post processing methods are suggested in order toapply the results to larger plates. Results are compared to the data of Regardin et al. (réf. [1])and emphasize some discrepancies with respect to the real case. Finally some improvementsto the test-rig are suggested for it to be more representative of the industrial situation.

This thesis deals with the near-field of confluent jets, which can be of interest in many engineering applications such as design of a ventilation supply device. The physical effect of interaction between multiple closely spaced jets is studied using experimental and numerical methods. The primary aim of this study is to explore a better understanding of flow and turbulence behavior of multiple interacting jets. The main goal is to gain an insight into the confluence of jets occurring in the near-field of multiple interacting jets. The array of multiple interacting jets is studied when they are placed on a flat and a curved surface. To obtain the boundary conditions at the nozzle exits of the confluent jets on a curved surface, the results of numerical prediction of a cylindrical air supply device using two turbulence models (realizable 𝑘 − 𝜖 and Reynolds stress model) are validated with hot-wire anemometry (HWA) near different nozzles discharge in the array. A single round jet is then studied to find the appropriate turbulence models for the prediction of the three-dimensional flow field and to gain an understanding of the effect of the boundary conditions predicted at the nozzle inlet. In comparison with HWA measurements, the turbulence models with low Reynolds correction (𝑘 − 𝜖 and shear stress transport [SST] 𝑘 − 𝜔) give reasonable flow predictions for the single round jet with the prescribed inlet boundary conditions, while the transition models (𝑘 − 𝑘l − 𝜔𝜔 and transition SST 𝑘 − 𝜔) are unable to predict the flow in the turbulent region. The results of numerical prediction (low Reynolds SST 𝑘 − 𝜔 model) using the prescribed inlet boundary conditions agree well with the HWA measurement in the nearfield of confluent jets on a curved surface, except in the merging region. Instantaneous velocity measurements are performed by laser Doppler anemometry (LDA) and particle image velocimetry (PIV) in two different configurations, a single row of parallel coplanar jets and an inline array of jets on a flat surface. The results of LDA and PIV are compared, which exhibit good agreement except near the nozzle exits. The streamwise velocity profile of the jets in the initial region shows a saddle back shape with attenuated turbulence in the core region and two off-centered narrow peaks. When confluent jets issue from an array of closely spaced nozzles, they may converge, merge, and combine after a certain distance downstream of the nozzle edge. The deflection plays a salient role for the multiple interacting jets (except in the single row configuration), where all the jets are converged towards the center of the array. The jet position, such as central, side and corner jets, significantly influences the development features of the jets, such as velocity decay and lateral displacement. The flow field of confluent jets exhibits asymmetrical distributions of Reynolds stresses around the axis of the jets and highly anisotropic turbulence. The velocity decays slower in the combined regio  of confluent jets than a single jet. Using the response surface methodology, the correlations between characteristic points (merging and combined points) and the statistically significant terms of the three design factors (inlet velocity, spacing between the nozzles and diameter of the nozzles) are determined for the single row of coplanar parallel jets. The computational parametric study of the single row configuration shows that spacing has the greatest impact on the near-field characteristics.

Les instabilités aéroélastiques de bandes d’acier constituent aujourd’hui l’un des problèmes majeurs dans les sections de refroidissement par jets impactants des lignes de recuit continues.En effet, le traitement thermique des nouveaux aciers nécessite de très fortes pentes de température impliquant constamment des augmentations de vitesse de soufflage susceptibles de mettre en jeu des instabilités aéroélastiques. Des flottements ainsi que des divergences de bande ont déjà été constatées et identifiées. Ces deux instabilités impliquent dans la plupart des cas des chocs entre la bande et les buses de soufflage ce qui engendre des défauts de surface sur la bande.Un banc d’essai a été conçu et fabriqué dans le but d’analyser ces instabilités et d’anticiper leur apparition. A partir d’observations, la dynamique structurelle de la bande a été simplifiée à un mode de rotation rigide. Le banc comporte une plaque oscillante en mouvement forcé.Celle-ci est impactée par un dispositif de plusieurs jets axisymétriques turbulents ayant une disposition identique à celle des tours industrielles. Les efforts aérodynamiques stationnaires et instationnaires agissant sur la plaque sont mesurés au moyen de capteurs de pression.L’impact de plusieurs jets en interaction crée de très importants gradients de pression sur la plaque il est donc nécessaire que la grille de prises de pression soit très fine pour que l’estimation des efforts aérodynamiques soit correcte. La plaque est donc instrumentée de 91capteurs de pression sur une surface de 18 cm². Elle peut également être translatée dans les ois directions de l’espace, ce qui permet d’obtenir la distribution des efforts instationnaires ainsi que des coefficients aéroélastiques sur une grande surface de plaque et à différentes distances d’impact.Les mesures de pression stationnaires ont permis d’établir les courbes d’évolution des efforts d’impact des jets sur la plaque en fonction de la distance jet-plaque ainsi que de la géométrie des buses. Les résultats ont permis de déterminer la stabilité statique de la plaque en mouvement de pompage. Les mesures de vitesses des jets libres ont été effectuées paranémométrie à fil chaud et ont permis de déterminer leurs propriétés statistiques.Les mesures de coefficients aéroélastiques sur la plaque en rotation ont été effectuées surune seule géométrie de soufflage, pour différentes vitesses réduites. Les résultats mettent en évidence l’importance des effets de bords sur la stabilité de plaque. Des méthodes de post traitements ont proposées afin d’extrapoler les résultats à différentes largeurs de bande. Ils sont confrontés aux travaux de Regardin et al. (réf. [1]) et mettent en évidence des désaccords avec le cas réel. Des suggestions sont apportées afin d’améliorer la représentativité du banc vis-à-vis des bandes industrielles. / Aeroelastic instabilities of steel strips impinged by arrays of cooling gas jets have becomeone of the main issues in cooling sections of continuous annealing lines. Indeed, the new steeltreatments require very high temperature variation rates which involve increases in jetvelocities that are likely to onset some aeroelastic instabilities. Strip flutter and divergencehave already been observed and identified. These two aeroelastic instabilities imply a strongrisk of contact with the blowing boxes, which can seriously blemish the strip.An experimental test rig was designed and built in order to analyze and predict of theseinstabilities. From observations, the strip’s structural dynamics was simulated by a rigidrotation mode. The rig included a forced oscillating plate which is impinged by an array ofaxisymmetric jets having the exact industrial geometry. The plate was instrumented withpressure sensors to measure the steady and unsteady surface pressures. The impingement ofinteracting jets creates very large pressure gradients on the plate and therefore a tight mesh ofpressure taps (91 over an 18cm² jet impingement surface) was necessary to allow a goodestimation of the aerodynamic loads The plate could also be moved in the three coordinatedirections as to obtain surface mappings of the unsteady jet forces and aeroelastic coefficientscan be obtained over a wide area and different jet-to-plate distances.The variation of the impinging aerodynamic forces was established as a function of the jetto-plate distance for different nozzle geometries. These results were used to determine the jetstatic stability in plunging motion. Velocity and turbulence measurements in free jets werecarried out using hot wire anemometry in order to determine their statistical properties.Aeroelastic coefficient measurements were carried out on the oscillating plate with onlyone nozzle geometry and different reduced velocities. Results show that the plate’s stability ismainly dependent on the boundary effects. Post processing methods are suggested in order toapply the results to larger plates. Results are compared to the data of Regardin et al. (réf. [1])and emphasize some discrepancies with respect to the real case. Finally some improvementsto the test-rig are suggested for it to be more representative of the industrial situation.

Les oscillateurs fluidiques qui peuvent générer des excitations périodiques sont des actionneurs très prometteurs pour des applications de contrôle actif des écoulements. Les oscillations sont en effet complètement auto-induites et produites en l'absence de parties mobiles ce qui rend ces actionneurs très intéressants en termes de fiabilité et de robustesse. Ce travail de thèse avait pour objectif principal d'identifier les mécanismes physiques qui contrôlent la dynamique de fonctionnement de ce type d'oscillateurs fluidiques et de proposer des lignes directrices pour la conception d'oscillateurs dont les performances soient adaptées aux applications de contrôle d'écoulements envisagées. L'analyse expérimentale de plusieurs prototypes couplée à des simulations numériques a permis de mettre en évidence que le mécanisme de basculement du jet dans ce type d'oscillateurs est contrôlé par les gradients de pression existants au niveau de deux parties critiques de ces actionneurs. A partir de cette analyse, une relation simple a été établie permettant d'estimer la fréquence des oscillations. Deux méthodes de synchronisation, permettant le contrôle du déphasage entre les actionneurs, ont été proposées et validées expérimentalement ainsi qu'à l'aide de simulations numériques. Une matrice de micro­ oscillateurs fluidiques a été conçue, fabriquée et finalement intégrée sur une rampe installée en soufflerie. L'analyse expérimentale de son efficacité pour le contrôle de l'écoulement séparé a mis en évidence un gain important par rapport aux résultats obtenus lors de travaux précédents sur des écoulements de paroi similaires à l'aide d'autres types d'actionneurs fluidiques. / Fluidic oscillators which can generate periodic excitations are very promising for active flow control applications, due to their reliability and robustness, as their internal flow oscillation is totally self-induced and self-sustained. The main objective of this work is to identify the underlying mechanisms controlling the dynamics of this kind of fluidic oscillator and to propose guiding lines for the design of oscillators. Experimental analysis of several oscillator prototypes and associated numerical simulations have permitted to explain that the jet switching in this kind of oscillator is controlled by pressure gradients in two critical parts of the device. From these analyses, a simple function has been proposed to estimate the oscillation frequency. Two synchronization methods, allowing the control of the phase lag between the actuators, have been proposed and validated experimentally and by numerical simulations. An array of micro-fluidic oscillators has then been designed and tested on a ramp separated flow, showing much higher efficiency compared to other kind of fluidic actuators tested on similar wall flows in previous studies.

This diploma thesis deals with the research of the flow in front of the benchmark automotive vent. Using thermoanemometry, the velocity field in the area in front of the vent was measured in detail and the intensity of the turbulence was calculated. Computational fluid dynamics of the air flow from the vent was also performed using the STAR-CCM + program. In addition, the influence of the surrounding surfaces simulating the real environment of the automobile on the air flow from the vent was investigated. The diploma thesis contains the calculation of measurement uncertainty. The purpose of this thesis is to obtain complex data on the velocity field and to use them for validation of Computational fluid dynamics.

The master’s thesis deals with air flow in the interior of automobile Škoda Octavia. The attention is focused only at a side ventilating outlet. Author’s effort was to propose the appropriate criteria for evaluation and assessment of ventilating outlet quality and elaborate the methodology of measurement for these criteria. Then follows the application of the methodology and measurement of velocity field of air flow from the outlet by the method of hot wire anemometry. The thesis also contains comparison of the results with the results attained by the smoke visualization.

In this master’s thesis there are summarized fundamental findings about air flow velocity measurements and afterwards introduced the measuring track for automobile car vents, measured object and track arrangement and all used components. Velocity field measurement method is how wire anemometry, and apart from 4 main cases measurements of free air jet, there are velocity profiles in piping measured as an input for CFD simulation. Air vent evaluation criteria are described and their assessment is done for specified cases. Further, there is a CFD simulation presented with comparison to experimental data. Uncertainty of flow rate measured and flow rate setting is determined. Improvement points and encountered issues are presented. Visualization and evaluation program coded in MATLAB environment enables easy data display of CTA results and will serve further vent quality assessment.

Pour mieux comprendre la combustion en mode stratifié, la propagation de flammes au sein de stratifications de richesse laminaire ou turbulente a été étudiée par des mesures simultanées de richesse et de vitesse effectuées par couplage de la PIV et de la PLIF. L’accent a été mis sur le développement de méthodes permettant d’améliorer la qualité des mesures locales. En particulier, un nouvel algorithme de PIV permettant la mesure locale de la vitesse des gaz frais véritablement à l’entrée de la zone de préchauffage a été développé. Pour améliorer la résolution,les mailles de calcul s’adaptent localement à la topologie de la flamme, pour tenir compte de la forme du front de flamme et de l’expansion des gaz. L’analyse statistique des mesures conditionnée sur la richesse locale a permis de caractériser les propriétés de la flamme soumise à une stratification de richesse dans un écoulement laminaire et turbulent, en particulier en mettant en évidence un effet mémoire. / In order to better understand the stratified combustion, the propagation of flame through stratified mixture field in laminar and turbulent flow conditions has been studied by using combined PIV/PLIF techniques. A great emphasis was placed on developing methods to improve the accuracy of local measurements of flame propagation. In particular, a new PIV approach has beendeveloped to measure the local fresh gas velocity near preheat zone of flame front. To improve the resolution of measurement, the shape of interrogation window has been continuously modified based on the local flame topology and gas expansion effect. Statistical analysis of conditioned local measurements by the local equivalence ratio of flames allows the characterization of theproperties of flame propagation subjected to the mixture stratification in laminar and turbulentflows, especially the highlight of the memory effect.

No description available.