Many environmental studies of water transport through the vadose zone require a field determination of saturated hydraulic conductivity. The purpose of this dissertation is to analyze the reliability of existing methods to determine saturated hydraulic conductivity, K(s), in the vadose zone from constant head borehole infiltration test data. In methods developed by the U. S. Bureau of Reclamation [USBRI, and in lesser known ones, K(s) is computed knowing the height of water in the borehole, length open to the formation, borehole radius, distance above the water table, and steady flow rate. The mathematical formulas on which these methods rest are derived on the basis of numerous simplifying assumptions. The free surface approach is used as the conceptual model of flow from a borehole. Results of numerical simulations are used to compare with the analytical solutions. Simulations with a steady-state finite element computer program, FREESURF, show that the Nasberg-Terletskata solution most closely approximates flow from a borehole with the free surface approach. The influence of capillarity is simulated for saturated-unsaturated porous media in four soils using a finite element computer program, FLUMP, and an integrated finite difference program, TRUST. Contrary to what one finds with the free surface approach, only a small portion of the flow field near the borehole is saturated at steady-state and the cross sectional area normal to the flow path increases with depth below the borehole. For deep water table conditions in fine textured soils, values of K(s) computed using the USBR open-hole equations may be more than 160% greater than the true values; and in coarse sands the USBR solutions may under-estimate the actual value by more than 35%. Mostly because of the influence of unsaturated soil properties there is no unique relationship between K(s), borehole conditions, and steady flow rate, as implied in the analytical solutions. Steady-state simulations demonstrate that existing solutions for borehole infiltration tests in anisotropic or nonuniform soils may also lead to significant errors. Time dependent simulations show that the time to reach a steady flow rate may be more than several days in very dry, low-permeable soils. The time to reach a steady flow rate can be significantly reduced by decreasing the open area between the borehole and formation while increasing the height of water in the borehole. Two methods are proposed to minimize the time, water volume requirements, and cost of conducting constant head borehole infiltration tests. Simulations show that a plot of the inverse of flow rate versus logarithm of time departs from a straight line after about 80% of the steady rate is achieved for various soil and borehole conditions; the steady rate is approximately 0.8 times the rate at the break in slope. In the second method flow rate is plotted versus the inverse of the square root of time and the steady rate is estimated within about 10% by linear extrapolation of early time measurements. USBR field data generally support this linear relationship. Two empirical equations are proposed to compute K(s). The first is applicable for a range of borehole conditions and approximately accounts for capillary effects with a single parameter. The second applies if the height of water in the borehole is I meter, and is based on the time to reach 80% of the steady rate and saturation deficit of the field soil.

The HYDROPAC model was developed to improve the technology transfer from the science of hydrology to environmental planning disciplines by initiating advanced spatial analysis techniques for predicting rainfall-runoff relationships. This model integrates the Soil Conservation Service (SCS) equations for calculating runoff and a Geographic Information System (Map Analysis Package) in a framework that allows the simulation of runoff processes over a digital elevation model. The simulations are done in discrete time steps allowing the generation of a hydrograph at any desired point in the watershed and the overland flow patterns are displayed in maps. This framework addresses some of the current limitations of hydrologic model for stormwater management planning in terms of capabilities for analysis and communication of results. This manuscript describes the methods used to develop the framework of the HYDROPAC model and its usefulness for analyzing potential runoff problems during the planning process.

A physically-based, user friendly, hydrologic computer simulation model was developed for pinyon-juniper woodland watersheds. The data requirements are minimum, requiring vegetation conditions, basic soil survey information, and daily values for precipitation and temperature. The model predicts runoff from cleared and uncleared watersheds by simulating hydrologic processes on a daily basis. The model was tested with data from small pinyon-juniper watersheds in central Arizona. A crack-forming vertisol was the dominant soil type, and a special feature for addressing its effects on runoff was included. No significant difference between predicted and observed annual runoff was found at the ninety-five percent confidence level.

The research project described in this dissertation studies the modelling techniques employed for the Mlazi River in the context of flood analysis and flood forecasting in order to model flood inundation. These techniques are applicable to an environment where there is uncertainty due to a lack of historical input data for calibration and validation purposes. This uncertainty is best explained by understanding the process and data required to model flood inundation. In order to model flood inundation in real time, forecasted flood flows would be required as input to a hydraulic river model used for simulating flood inundation levels. During this process, forecasted flood flows would be obtained from a flood-forecasting model that would need to be calibrated and validated. The calibration process would require historical rainfall data correlating with streamflow data and subsequently, the validation process would require real time streamflow data. In the context of the Mlazi Catchment, there are only two stream gauges located in the upper subcatchments. Although these stream gauges have recorded data for 20 years, the streamflow data does not correlate with disaggregated daily rainfall data, of which there are records for at least 40 years. Therefore it would be difficult to develop the forecasting model based on the rainfall and streamflow data available. In this instance, a more realistic approach to modelling flood inundation involved the integration of GIS technology, a physically based hydrological model for flood analysis, a conceptual forecasting model for real time forecasting and a hydraulic model for computation of inundation levels. The integration of modelling techniques are better explained by categorising the process into three phases: Phase 1 Desktop catchment modelling: A continuous, physically based simulation model (HEC-HMS Model) was set up using GIS technology. The model applied the SCS-UH method for the estimation of peak discharges. Synthetic hyetographs for various recurrence intervals were used as input to the model. A sensitivity analysis was implemented and subsequently the HEC-HMS model was calibrated against output SCS-UH method and peak discharges simulated. The synthetic hyetographs together with results from the HEC-HMS model were used for validation of the Mlazi Meta Model (MMM) used for real time flood forecasting. Phase 2 Implementation of the Inundation Model: The hydraulic model (HEC-RAS) was created using a Digital Elevation Model (DEM). A field survey was conducted for the purpose of capturing the roughness coefficients and hydraulic structures, which were incorporated into the model and also for the confirmation of the terrain cross sections from the DEM. Flow data for the computation of levels of inundation were obtained from the HEC-HMS model. The levels of inundation for the natural channel of Mlazi River were simulated using the one dimensional steady state analysis, whereas for the canal overbank areas, simulation was conducted for unsteady state conditions. Phase 3 Creation of the Mlazi Meta Model (MMM): The MMM used for real time flood forecasting is a linear catchment model which consists of a semi-distributed three reservoir cell model (Pegram and Sinclair, 2002). The MMM parameters were initially adjusted using the HEC-HMS model so that it became representative of the Mlazi catchment. This approach sounds unreasonable because a model is being validated by another model but it gave the best initial estimate of the parameters rather than using trial and error. The MMM will be further updated using record radar data and streamflow data once all structures have been put in place. The confidence in the applicability of the HEC-HMS model is based on the intensive efforts applied in setting it up. Furthermore, the output results from the calibrated HEC-HMS model were compared with other reliable methods of computing design peak discharges and also validated with frequency analysis conducted on one of the subcatchments. / Thesis (M.Sc.)-University of Natal, Durban,2003.

This thesis presents the development of a dual-isotope simulation in a hydrological model, and its application to the lower Nelson River basin. The purpose of this study is to find if the simulation of stable water isotopes aids in hydrological simulation, and if a dual-isotope simulation is an improvement over a single-isotope simulation. The isoWATFLOOD model was enhanced to include δ2H and improve physical representativeness. The model was calibrated using various isotope and flow simulation error functions. Internal hydrologic storages and fluxes were verified by comparing simulated isotope values to observed isotope data. Adding isotope error to the calibration resulted in small but consistent improvements to the physical basis of calibrated parameter values. Isotope simulation error was found to be the best predictor of streamflow simulation performance beyond the calibration period. The dual-isotope simulation identified a number of model limitations and potential improvements from the verification of internal hydrologic storages. / October 2016

Climate models are common tools for developing design standards in the hydrologic field; however, these models contain uncertainties in multi-model and scenario selections. Along with these uncertainties, biases can be attached to the models. Such biases and uncertainties can present difficulties in predicting future extremes. These hydrologic extremes are believed to be non-stationary in character. Only in the recent past have model users come to terms that the current hydrologic designs are no longer relevant due to their assumption of stationarity. This study describes a systematic method of selecting a best fit model in relationship to location and time, along with the use of that best fit model for evaluation of future extremes. Rain gage stations throughout Florida are used to collect daily precipitation data used in extreme precipitation and quantitative indices. Through these indices conclusions are made on model selection and future extremes, as they relate to hydrologic designs. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2013.

A carência, absoluta ou relativa, de água direcionou diversas ações no sentido de amenizar esse problema. A política nacional de recursos hídricos (Lei 9.433/97), com seus cinco instrumentos de gestão e planejamento, pode ser considerada o principal marco. Entre esses instrumentos, encontra-se o sistema de informações, que tem por finalidade coletar, armazenar e disponibilizar dados para uma gestão racional. É nesse âmbito e no sentido de contribuir para a evolução desses sistemas, que se apresenta essa tese de doutoramento. O tema principal trata da implementação de um sistema de suporte a decisões – SSD com base nos conceitos da programação orientada a objetos – POO, forma esta de programação que procura representar os sistemas por meio de classes de maneira a buscar a semelhança à realidade. Esse SSD, denominado de ARENA (análise de recursos naturais), é composto de um sistema de informações geográficas – SIG, dois simuladores (simulação do fluxo de águas subterrâneas e do ciclo hidrológico superficial), uma base de dados georeferenciada e módulos de acesso aos dados. A forma como os simuladores foram implementados, baseado em conceitos da POO e suas integrações às entidades geométricas do SIG, é apresentada como contribuição. No ARENA, o SIG não é apenas utilizado nas fases de pré e pós-processamento de dados para modelos, e sim no processo de simulação. Aplicações do ARENA a uma bacia hidrográfica (escoamento superficial) e a dois sistemas hipotéticos (escoamento subterrâneo) são apresentados ao final do trabalho. A maneira como esse SSD foi implementado induz ao desenvolvimento de simuladores adicionais sem realizar modificações nos pacotes já implementados neste trabalho, sendo facilitada a utilização dos pacotes que compõem esse SSD / The relative or complete lack of water has been directing various actions in order to solve this problem. The national water resources politic (Law 9.433/97) with its five instruments for water resources planning and management can be considered the main action. Among these instruments, it is found the information system that has as purpose to collect, store and turn it into available data to the rational management. In this scope and in order to give some contributions to the improvement of these systems, this Ph.D. thesis is presented. The main topic deals with the decision support system (DSS) implementation based on oriented object – OO, a kind of programming which tries to represent systems through classes very closely to the reality. This DSS, called ARENA (análise de recursos naturais, in Portuguese), is made up of a geographic information system (GIS), two models (a groundwater model and a distributed rainfall-runoff model), a georeferenced database and graphic user interfaces (GUI). The way the models were built, based on OO concepts and its integration to GIS geographic data, is presented as contribution. In the ARENA, the GIS is not only used in the pre and post processing steps, but also in the simulation. The ARENA applications were carried out for two examples, a watershed (surface water simulation) and a hypothetic system (groundwater simulation), both presented in the end of this study. The way this DSS was built induces to the development of other models without modifications in the existing packages, so that the development of new applications becomes easy because the use of existing packages that made this DSS up

Three major teleconnections, Atlantic Multidecadal Oscillation (AMO), North Atlantic Oscillation (NAO), and the Pacific Decadal Oscillation (PDO), in warm and cool phases, effect precipitation in Florida. The effects of the oscillation phases on the precipitation characteristics are analyzed by using long-term daily precipitation data, on different temporal (annual, monthly, and daily) and spatial scales, utilizing numerous indices, and techniques. Long-term extreme precipitation data for 9 different durations is used to examine the effects of the oscillation phases on the rainfall extremes, by employing different parametric and non-parametric statistical tests, along with Depth-Duration- Frequency analysis. Results show that Florida will experience higher rainfall when AMO is in the warm phase, except in the panhandle and south Florida, while PDO cool phase is positively correlated with precipitation, except for the southern part of the peninsula. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2013.

At the large watershed scale, we emphasize the effects of flow through a river network on streamflow under dry conditions. An immediate consequence of assuming dry conditions is that evapotranspiration causes flow in the river network to exhibit oscillations. When all links in the river network combine their flow patterns, the oscillations interact in ways that change the timing and amplitude of the streamflow waves at the watershed outlet. The geometric shape of the river network is particularly important, so we develop an analytic solution for streamflow which emphasizes that importance. Doing hydrology backward is a strategy recently developed by several researchers to deal with uncertainty in measurements of forcing terms applied to hydrologic models. The strategy has also been applied to resolve the assumption of homogeneity on realistic catchments that exhibit many heterogeneous properties. In this work, we demonstrate hydrology in the backward direction applied to two examples: using streamflow at the catchment scale to determine runoff at the hillslope scale and using the hillslope runoff to infer the applied evapotranspiration forcing under the assumption of dry conditions. In order to work across scales, we utilize the analytic solution for streamflow at the outlet of a river network. At the hillslope scale, we develop a soil model to create fluxes consistent with observed soil processes.

Green Stormwater Infrastructure (GSI) has become a popular method for flood mitigation as it can prevent runoff from entering streams during heavy precipitation. In this study, a recently developed neighborhood in Gresham, Oregon hosts a comparison of various GSI projects on runoff dynamics. The study site includes dispersed GSI (rain gardens, retention chambers, green streets) and centralized GSI (bioswales, detention ponds, detention pipes). For the 2017-2018 water year, hourly rainfall and observed discharge data is used to calibrate the EPA's Stormwater Management Model to simulate rainfall-runoff dynamics, achieving a Nash-Sutcliffe efficiency of 0.75 and Probability Bias statistic of 3.3%. A synthetic scenario analysis quantifies the impact of the study site GSI and compares dispersed and centralized arrangements. Each test was performed under four precipitation scenarios (of differing intensity and duration) for four metrics: runoff ratio, peak discharge, lag time, and flashiness. Design structure has significant impacts, reducing runoff ratio 10 to 20%, reducing peak discharge 26 to 68%, and reducing flashiness index 56 to 70%. There was a reverse impact on lag time, increasing it to 50 to 80%. Distributed GSI outperform centralized structures for all metrics, reducing runoff ratio 22 to 32%, reducing peak discharge 67 to 69%, increasing lag time 133 to 500%, and reducing flashiness index between 32 and 62%. This research serves as a basis for researchers and stormwater managers to understand potential impact of GSI on reducing runoff and downstream flooding in small urban watersheds with frequent rain.