Several recent projects in building science have examined the hygric performance of building materials. Most building materials adsorb from and desorb water vapour to their environments. This phenomenon could be used to help control relative humidity fluctuations in buildings, experienced during periods of moisture production such as cooking, washing or bathing. They could also be used to reduce the need for mechanical ventilation and air conditioning to remove excess moisture. To understand how a building material responds to transient changes in relative humidity, testing is required.<p> This thesis outlines the testing performed on gypsum board, a common wall and ceiling finishing material used inside buildings. The effect of paint coatings on the gypsum boards and heat and mass transfer coefficients of the air passing over the gypsum bed was tested. The data produced from these experiments was used to validate several numerical models through an International Energy Agency/Energy Conservation in Buildings and Community Systems (IEA/ECBCS), Annex 41: Whole Building Heat, Air and Moisture Response. The validated models are important for simulating the process of adsorption and desorption in building materials to predict failure in the building envelope and expected indoor air conditions.<p> A sensitivity analysis is also presented which examines the effects of the sorption isotherm and vapour permeability of the gypsum and paints as well as the heat and mass transfer coefficients the boards are exposed to. The sensitivity range used was determined from the tests performed on the gypsum boards and paints which were also performed during the work of Annex 41.<p> The results of this thesis produced a high quality data which can also be used to validate future numerical models. All information required for validation of future models is available such as dimensions of test section, test conditions, material properties and the experimental data.<p> The results show that when designing for passive humidity control in buildings using gypsum boards, the most influential factor is the type of coating or paint applied to the surface. The sensitivity analysis showed that material properties such as vapour permeability and the sorption isotherms, for the expected temperature range, should be well known for increased accuracy of the simulation. The material properties were determined from inter-laboratory testing at 14 different institutions to achieve confident values.<p> The effect of increasing the heat and mass transfer coefficients, over the range of coefficients studied in this thesis, showed negligible differences in the results. The simulated results had very good agreement between the models and were mostly within experimental uncertainty of the measurements.

Several recent projects in building science have examined the hygric performance of building materials. Most building materials adsorb from and desorb water vapour to their environments. This phenomenon could be used to help control relative humidity fluctuations in buildings, experienced during periods of moisture production such as cooking, washing or bathing. They could also be used to reduce the need for mechanical ventilation and air conditioning to remove excess moisture. To understand how a building material responds to transient changes in relative humidity, testing is required.<p> This thesis outlines the testing performed on gypsum board, a common wall and ceiling finishing material used inside buildings. The effect of paint coatings on the gypsum boards and heat and mass transfer coefficients of the air passing over the gypsum bed was tested. The data produced from these experiments was used to validate several numerical models through an International Energy Agency/Energy Conservation in Buildings and Community Systems (IEA/ECBCS), Annex 41: Whole Building Heat, Air and Moisture Response. The validated models are important for simulating the process of adsorption and desorption in building materials to predict failure in the building envelope and expected indoor air conditions.<p> A sensitivity analysis is also presented which examines the effects of the sorption isotherm and vapour permeability of the gypsum and paints as well as the heat and mass transfer coefficients the boards are exposed to. The sensitivity range used was determined from the tests performed on the gypsum boards and paints which were also performed during the work of Annex 41.<p> The results of this thesis produced a high quality data which can also be used to validate future numerical models. All information required for validation of future models is available such as dimensions of test section, test conditions, material properties and the experimental data.<p> The results show that when designing for passive humidity control in buildings using gypsum boards, the most influential factor is the type of coating or paint applied to the surface. The sensitivity analysis showed that material properties such as vapour permeability and the sorption isotherms, for the expected temperature range, should be well known for increased accuracy of the simulation. The material properties were determined from inter-laboratory testing at 14 different institutions to achieve confident values.<p> The effect of increasing the heat and mass transfer coefficients, over the range of coefficients studied in this thesis, showed negligible differences in the results. The simulated results had very good agreement between the models and were mostly within experimental uncertainty of the measurements.

L’évolution actuelle des exigences en termes de performance énergétique des bâtiments a fait apparaître de nouveaux enjeux et problématiques scientifiques, dont ceux liés à l’humidité. Cette étude s’appuie sur une cellule expérimentale construite sur la technologie des maisons à ossature bois et soumise aux conditions climatiques réelles de Grenoble. L’instrumentation de ce bâtiment et le suivi de l’évolution en température et en humidité dans les différentes couches de l’enveloppe permettent de définir des séquences nécessaires à la validation de modèles numériques. Dans cet objectif, un modèle existant nommé HAM-Tools a été utilisé pour simuler les transferts couplés de chaleur, d’air et d’humidité à l’échelle du bâtiment. La démarche de validation a été décomposée en plusieurs étapes, de manière à cibler des transferts spécifiques et d’en améliorer la modélisation. Ces études localisées concernent les transferts couplés de chaleur et de masse à travers les parois solides, la modélisation des transferts de chaleur à travers une lame d’air ventilée et enfin la modélisation du renouvellement de l’air intérieur en conditions naturelles. Pour estimer la précision globale du modèle, c'est-à-dire à l’échelle du bâtiment, une séquence expérimentale a été simulée en prenant en compte l’ensemble des transferts couplés simultanément. Les performances du modèle sont discutées à partir des mesures locales, c'est-à-dire dans les parois, puis globales. La bonne concordance entre mesures et résultats de simulation permet de conclure sur la validité et la généricité de la démarche mise en œuvre et les hypothèses de simulation. Plus particulièrement, il est apparu que l’outil de modélisation permet de prédire correctement le comportement moyen des parois en humidité et en température. Il est donc envisageable de l’utiliser pour simuler et estimer l’impact des constituants des parois en termes de durabilité, de performances énergétiques et de confort de l’occupant. / As energy saving is so important in buildings nowadays, envelopes performances have to be more efficient and have to deal with more obligations, such as moisture accumulation and mould growth. This study relies on an experimental wooden frame house exposed to the natural conditions of Grenoble, France. It has been widely instrumented so the wall’s temperature and humidity is monitored at different depths. As a consequence, complete dataset are available and can be used to validate numerical model. In this work, an existing numerical model named HAM-Tolls has been used to simulate the heat, air and moisture coupled transfers at the building scale. The method developed here consists in validating the numerical model step by step, with studying specific transfers separately. The first step deals with heat and mass transfers across the walls. Then, the heat transfers across a ventilated air gap and the air change rate under natural conditions have been studied much in detail. The final step of this works consists in simulating simultaneously every transfer at the building scale. This latest simulation’s results were compared both on a local and on a global point of view with the measurements. As they were found to be in good agreement, this allows concluding on the methodology efficiency, the validity of the modelling assumption and gives good hope with extending this methodology to other studies. Specifically, the simulation tool is able to predict correctly the average temperature and humidity content within the walls. Therefore, it should be suitable with estimating the wall components influence on the wall durability, its energy efficiency and its impact on the occupant’s thermal comfort.