Thesis (Ph. D.)--University of Texas at Austin, 2001. / Vita. Includes bibliographical references (leaves 178-183). Available also in a digital version from Dissertation Abstracts.

During unstart, the rapid upstream propagation of a hypersonic engine's inlet shock system can be clearly seen through inlet pressure measurements. Specifically, the magnitude of the pressure readings suddenly and dramatically increases as soon as the leading edge of the shock system passes the measurement location. A change detection algorithm can monitor the pressure time history at a given sensing location and determine when an abrupt pressure rise occurs. If this kind of information can be obtained at various sensing locations distributed throughout the inlet then a feedback control scheme has an improved basis upon which to make actuation decisions for preventing unstart. In this thesis a variety of change detection algorithms have been implemented and tested on multiple sources of experimental high-speed pressure transducer data. The performance of these algorithms is compared and suitability of each algorithm for the general unstart problem is discussed. Attempts to model the transient dynamics governing the unstart process have also been made through the use of system identification techniques. The result of these system identification efforts is a partially nonlinear mathematical model that describes shock motion through pressure signals. The process reveals that the nonlinear behavior can be separated from the linear with relative ease. Related attempts are then made to create a model where the nonlinear portion has been specified leaving only the linear portion to be determined by system identification. The modeling and identification process specific to the unstart data used is discussed and successful models are presented for both cases. / text

Not available / text

This study investigates the design and aeropropulsive performance of a complete, hydrogen powered, shock-induced combustion ramjet (shcramjet) at a flight Mach number of 11 and altitude of 34.5 km. The design includes a Prandtl-Meyer compression inlet, cantilevered ramp fuel injectors, a shock-inducing wedge and a divergent nozzle. Numerical studies are undertaken using the WARP code that solves the three-dimensional Favre-averaged Navier-Stokes equations closed by the Wilcox k-ω turbulence model and the Jachimowski H2/air chemical kinetics model. Studies of fuel injection properties, mixing duct length, combustor wedge and nozzle geometry are completed to maximize the overall performance of the vehicle. The final shcramjet configuration generates a specific impulse of 1110 s. A comparison is undertaken with a scramjet vehicle at identical flight conditions and using many of the same components. The comparable scramjet generates a higher specific impulse of 1450 s although it is significantly larger and therefore heavier.

This study investigates the design and aeropropulsive performance of a complete, hydrogen powered, shock-induced combustion ramjet (shcramjet) at a flight Mach number of 11 and altitude of 34.5 km. The design includes a Prandtl-Meyer compression inlet, cantilevered ramp fuel injectors, a shock-inducing wedge and a divergent nozzle. Numerical studies are undertaken using the WARP code that solves the three-dimensional Favre-averaged Navier-Stokes equations closed by the Wilcox k-ω turbulence model and the Jachimowski H2/air chemical kinetics model. Studies of fuel injection properties, mixing duct length, combustor wedge and nozzle geometry are completed to maximize the overall performance of the vehicle. The final shcramjet configuration generates a specific impulse of 1110 s. A comparison is undertaken with a scramjet vehicle at identical flight conditions and using many of the same components. The comparable scramjet generates a higher specific impulse of 1450 s although it is significantly larger and therefore heavier.

No description available.

No description available.

No description available.

Scramjet engines are the focus of considerable interest for propulsion in the hypersonic flow regime. One of the serious technical challenges for developing scramjets is reducing the skin friction drag on the engine. The combustion chamber, in particular, is a major contributor to the skin friction drag because of the high density of the flow through that region. This investigation focuses on reducing the combustion chamber skin friction drag by minimising the surface area and size of the combustion chamber and by employing a novel approach to accomplishing combustion. The first design criterion is addressed by using a single internal-combustor scramjet configuration, as opposed to multiple external combustors, and by injecting the fuel on the intake to reduce the mixing length required in the combustor. The second design criterion refers to the use of a new technique called radical farming. This uses the highly two-dimensional nature of the flow through the engine, which is created by deliberately ingesting the leading edge shocks, to achieve combustion at lower mean static pressures and temperatures than generally expected. A simplified approximate theoretical analysis of the radical farming concept is presented. Experiments were conducted in the T4 free-piston shock tunnel on a scramjet model with a single rectangular constant cross-sectional area combustion chamber. Pressure measurements were taken along the centreline of the intake, combustion chamber and thrust surface and across the model width at three locations. Gaseous hydrogen fuel was injected halfway along the intake at a range of equivalence ratios between zero and one. The combustion chamber height was varied from 20mm to 32mm, which varied the contraction ratio of the engine from 4.1 to 2.9. The experiments were conducted at a stagnation enthalpy of either 3MJ/kg or 4MJ/kg. The nominal 3MJ/kg condition corresponds to Mach 7.9 flight at an altitude of 24km. The majority of the 4MJ/kg experiments were conducted at a nominal condition corresponding to Mach 9.1 flight at an altitude of 32km. A small number of 4MJ/kg experiments were conducted at simulated flight altitudes of between 30 and 38km; the flight Mach number for these experiments was approximately 9.0. Thrust was calculated by integrating the centreline pressure distribution over the area of the thrust surface, assuming that the pressure at any axial location was constant across the engine width. These experimental thrust values were compared with theoretical estimates obtained using a one-dimensional analysis and a quasi-two-dimensional analysis. The comparison provided an indication of the level of completion of combustion in the experiments. The difference in thrust produced as a result of combusting fuel was examined by plotting the incremental specific impulse against equivalence ratio. Experimental and theoretical results agreed best at the higher equivalence ratios. Turbulent boundary layer separation correlations were used to provide reasonable estimates for the equivalence ratio at which the flow choked. The drag on the internal flowpath of the scramjet engine was estimated using the quasi-two-dimensional analysis. This drag estimate was combined with the experimental thrust measurements to provide estimates of the net specific impulse. Positive net specific impulse estimates were obtained above a certain minimum equivalence ratio, which depended on the contraction ratio and the test condition. The engine performance was observed to be highly dependent on the two-dimensional shock structure within the engine. Thrust and specific impulse were observed to decrease with increasing simulated flight altitude, as expected. Positive net specific impulse estimates were obtained at equivalence ratios of approximately one for simulated flight altitudes below 35km. Assuming complete combustion and that an equivalence ratio of one can be reached, the configuration considered in the present study can theoretically reach a net specific impulse of approximately 1000s at the 3MJ/kg condition and 500s at the 4MJ/kg condition. These numbers provide a promising testimonial for the use of this configuration, with modifications, as a more efficient alternative to rocket engines.

Thesis (M.S.)--University of Missouri--Rolla, 2007. / Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed March 25, 2008) Includes bibliographical references (p. 95-97).