1 |
Investigation and prediction of autoignition during hot start conditionsWodausch, Jens January 2009 (has links)
This Master’s thesis discusses the investigation of autoignition (knock) of air-fuel mixtures in internal combustion engines (type EA 827; 1.6 and 1.4 l) under hot start conditions. Chapter Three comprehensively reviews literature on fuel characteristics; specifically boiling point, chemistry and the difference between the Research and Motor Octane Number (RON and MON). Furthermore different types of autoignition are discussed with regards to their detection and assessment in the chapter. The subsection on engine management looks at possible methods of altering and eliminating autoignition. Chapter Four details the equipment used to obtain data and measurements, as well as the signal conditioning of the spark and injector signal. Chapter Five discusses the actual results obtained during summer testing of the different methods of altering and eliminating autoignition in an internal combustion engine, as derived from the theories presented in Chapter Three. The summer tests finally verified the new application level and showed that only a reduction in the quantity of fuel injected can eliminate autoignition. However, a slight decrease in heat release does cause an increase in start time. In Chapter Six, based on the test results, a simulation model which calculates the probability of autoignition in a 1.4 l (Econo) engine during hot start conditions in Matlab/Simulink was developed. This simulation model satisfactorily verified test results.
|
2 |
A laser spark plug ignition system for a stationary lean-burn natural gas reciprocating engineMcIntyre, Dustin L. January 1900 (has links)
Thesis (Ph. D.)--West Virginia University, 2007. / Title from document title page. Document formatted into pages; contains xxiii, 284 p. : ill. (some col.). Vita. Includes abstract. Includes bibliographical references (p. 227-235).
|
3 |
Cycle-to-cycle variations in spark-ignition enginesKapil, Anil January 1988 (has links)
Pressure data measurements have been made in a single-cylinder, spark-ignition engine over 100 consecutive cycles. The engine was operated on natural gas at a wide range of engine speed and equivalence ratios. The effects of spark electrode geometry, combustion chamber geometry, spark gap and throttling have also been examined. From these pressure measurements standard deviations in burning times in mass-fraction-burned values were determined. Because of the existing evidence that the origin of cyclic variations is in the early combustion period, the standard deviations of cyclic variation in time required for a small (almost zero) mass-fraction-burned is estimated by extrapolation. These extrapolated values of standard deviation are compared with the implication of a hypothesis that cyclic variations in combustion in spark-ignition engines originate in the small-scale structure of turbulence (after ignition).
The nature of turbulence structure during combustion is deduced
from existing knowledge of mixture motion within the combustion chamber
of the engine. This research determines the turbulent parameters, such
as turbulence intensity, turbulent length scales and laminar burning
velocity. The standard deviation in burning times in the early stages
of combustion is estimated, within experimental uncertainty, by the
parameter ⋋/4uℓ where ⋋ is the Taylor microscale and uℓ is the laminar
burning velocity of the unburned mixture. This parameter is the
consequence of the Tennekes model of small-scale structure of
turbulence and Chomiak's explanation of the high flame propagation
rate in regions of concentrated vorticity and the assumption that theignition behaves as though it were from a point source.
The general conclusion reached is that the standard deviation in the burning time for small mass-fraction-burned is associated with the early stages of burning-predictable from the knowledge of the Taylor microscale and the laminar burning velocity. / Applied Science, Faculty of / Mechanical Engineering, Department of / Graduate
|
4 |
Modeling of Pre-ignition and Super-knock in Spark Ignition Enginesmubarak ali, mohammed jaasim 07 1900 (has links)
Advanced combustion concepts are required to meet the increasing global energy demand and stringent emission regulations imposed by the governments on automobile manufacturers. Improvement in efficiency and reduction in emissions can be achieved by downsizing the Spark Ignition (SI) engines. The operating range of SI engine is limited by occurrence of knock, pre-ignition and the following super-knock due to boosting of intake pressure, to account for the reduction of power, as a result of downsizing the engine. Super-knock, which represents high momentary pressure accompanied with pressure oscillations, is known to permanently damage the moving component of the engines. Therefore fundamental comprehensive understanding of the mechanism involved in pre-ignition and super-knock are required to design highly efficient spark ignition engines with lower emissions that can meet the increasing government regulations.
\nThe thesis focuses on auto-ignition characteristics of endgas and the bulk mixture properties that favor transition of pre-ignition to super-knock. Direct numerical studies indicate that super-knock occurs to due to initiation of premature flame front that transition into detonation. In literature, many sources are reported to trigger pre-ignition. Due to the uncertainty of the information on the sources that trigger pre-ignition, it is extremely difficult to predict and control pre-ignition event in SI engines. Since the information on the source of pre-ignition is not available, the main focus of this work is to understand the physical and chemical mechanisms involved in super-knock, factors that influence super-knock and methods to predict super-knock.
\n
Pre-ignition was initiated at known locations and crank angle using a hotspot of known size and strength. Different parametric cases were studied and the location and timing of pre-ignition initiation is found to be extremely important in determining the transition of pre-ignition event to super-knock. Pre-ignition increases the temperature of the endgas and the overall bulk mixture, that transitions the pre-ignition flame front to a detonation. The transition of the flame propagation mode from deflagration to detonation was investigated with different type of analysis methods and all results confirmed the transition of pre-ignition flame front to detonation that results in super- knock.
|
5 |
The performance stability of a homogeneous charge lean-burn spark-ignition engineGidney, Jeremy January 1990 (has links)
No description available.
|
6 |
The effect of the composition of wood on its thermal degradationMackinnon, Alexander J. January 1987 (has links)
No description available.
|
7 |
Ignition characteristics of plasticsThomson, Hilary Elizabeth January 1988 (has links)
No description available.
|
8 |
Combustion processes within a gas fired pulsed combustorLeng, Jing January 1995 (has links)
No description available.
|
9 |
Modelling and simulation of combustion-driven oscillations in laminar flamesAvelino, Juan Carlos Prince January 1994 (has links)
No description available.
|
10 |
Flame development in swirling flows in closed vesselsHanson, R. J. January 1981 (has links)
No description available.
|
Page generated in 0.0975 seconds