Harnessing the Sun’s energy via the conversion of solar photons to electricity has emerged as a sustainable energy source to fulfill our future demands. In this regard, solution-processable, size-tunable PbS quantum dots (QDs) have been identified as a promising active materials for photovoltaics (PVs). Yet, there are still serious challenges that hinder the full exploitation of QD materials in PVs. This dissertation addresses two main challenges to aid these QDs in fulfilling their tremendous potential in PV applications. First, it is essential to establish a large-scale synthetic technique which maintains control over the reaction parameters to yield QDs with well-defined shape, size, and composition. Rigorous protocols for cost-effective production on a scale are still missing from literature. Particularly, previous reports of record-performance QD-PVs have been based on small-scale, manual, batch syntheses. One way to achieve a controlled large-scale synthesis is by reducing the reaction volume to ensure uniformity. Accordingly, we design a droplet-based continuous-flow synthesis of PbS QDs. Only upon separating the nucleation and growth phases, via a dual-temperature-stage reactor, it was possible to achieve high-quality QDs with high photoluminescence quantum yield (50%) in large-scale. The performance of these QDs in a PV device was comparable to batch-synthesized QDs, thus providing a promise in utilizing automated synthesis of QDs for PV applications. Second, it is crucial to study and control the charge transfer (CT) dynamics at QD interfaces in order to optimize their PV performance. Yet, the CT investigations based on PbS QDs are limited in literature. Here, we investigate the CT and charge separation (CS) at size-tunable PbS QDs and organic acceptor interfaces using a combination of femtosecond broadband transient spectroscopic techniques and steady-state measurements. The results reveal that the energy band alignment, tuned by the quantum confinement, is a key element for efficient CT and CS processes. Additionally, the presence of interfacial electrostatic interaction between the QDs and the acceptors facilitates CT from large PbS QD (bandgap < 1 eV); thus enabling light-harvesting from the broad near-infrared solar spectrum range. The advances in this work – from automated synthesis to charge transfer studies – pave new pathways towards energy harvesting from solution-processed nanomaterials.

No description available.

It is known that organic monolayers on solid surfaces can enable electronic properties that are absent in the bulk of the solid materials. Often, once the organic film come into the contact with a solid surface, the established electronic interaction at their interface remains undisturbed. However, using a redox-active organic monolayer creates the possibility for modulating the extent and the direction of the interfacial charge transfer, establishing a switch at the interface. The theme of this thesis is investigation of the interfacial interaction of different redox states of a molecular switch, phenyl-capped aniline tetramer (PCAT) with iron oxide and graphite surfaces and their potential application in electronic devices. The nucleation and growth of submonolayer films of different oxidation states of PCAT on iron oxide surface was studied. Using atomic force microscopy and scaling island size distribution method the surface diffusion parameters of these islands were evaluated. Using X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy the changes in these organic monolayers before and after interaction with iron oxide were demonstrated. However, these techniques were unable to provide similar data from the solid surface side of the interface. Instead, we were able to demonstrate the changes in the iron oxide film as a result of interfacial charge transfer using electrical conductivity measurement techniques. Based on this information a microfluidic chemical sensor based on the interface of pencil film and PCAT for quantification of free chlorine in drinking water was constructed. Using XPS and UV-vis spectroscopy it was shown that the interaction the organic monolayer with sodium hypochlorite solution leads to the development of positive charges on the backbone of PCAT. This electrostatic charge can affect the charge transport in the pencil film causing the modulation of electrical conductivity of the film. The presented work demonstrates alternative pathways for the design of novel hybrid electronic devices based on thin molecular film and solid surfaces. / Thesis / Doctor of Philosophy (PhD)

Biomaterials-associated thrombosis is dependent critically upon electrochemical response of fibrinogen on material surface. The relationship between the response and anti-thrombogenicity of biomaterials is not well-established. Titanium oxide appears to have good anti-thrombogenicity and little is known about its underlying essential chemistry. We correlate their anti-thrombogenicity directly to electrochemical behaviors in fibrinogen containing buffer solution. High degree of inherent n-type doping was noted to contribute the impedance preventing charge transfer from fibrinogen into film (namely its activation) and consequently reduced degree of anti-thrombogenicity. The impedance was the result of high donor carrier density as well as negative flat band potential.

This thesis presents a mathematical model of the nanoporous anode within a dyesensitised solar cell (DSC). The main purpose of this work is to investigate interfacial charge transfer and charge transport within the porous anode of the DSC under both illuminated and non-illuminated conditions. Within the porous anode we consider many of the charge transfer reactions associated with the electrolyte species, adsorbed dye molecules and semiconductor electrons at the semiconductor-dye- electrolyte interface. Each reaction at this interface is modelled explicitly via an electrochemical equation, resulting in an interfacial model that consists of a coupled system of non-linear algebraic equations. We develop a general model framework for charge transfer at the semiconductor-dye-electrolyte interface and simplify this framework to produce a model based on the available interfacial kinetic data. We account for the charge transport mechanisms within the porous semiconductor and the electrolyte filled pores that constitute the anode of the DSC, through a one- dimensional model developed under steady-state conditions. The governing transport equations account for the diffusion and migration of charge species within the porous anode. The transport model consists of a coupled system of non-linear differential equations, and is coupled to the interfacial model via reaction terms within the mass-flux balance equations. An equivalent circuit model is developed to account for those components of the DSC not explicitly included in the mathematical model of the anode. To obtain solutions for our DSC mathematical model we develop code in FORTRAN for the numerical simulation of the governing equations. We additionally employ regular perturbation analysis to obtain analytic approximations to the solutions of the interfacial charge transfer model. These approximations facilitate a reduction in computation time for the coupled mathematical model with no significant loss of accuracy. To obtain predictions of the current generated by the cell we source kinetic and transport parameter values from the literature and from experimental measurements associated with the DSC commissioned for this study. The model solutions we obtain with these values correspond very favourably with experimental data measured from standard DSC configurations consisting of titanium dioxide porous films with iodide/triiodide redox couples within the electrolyte. The mathematical model within this thesis enables thorough investigation of the interfacial reactions and charge transport within the DSC.We investigate the effects of modified cell configurations on the efficiency of the cell by varying associated parameter values in our model. We find, given our model and the DSC configuration investigated, that the efficiency of the DSC is improved with increasing electron diffusion, decreasing internal resistances and with decreasing dark current. We conclude that transport within the electrolyte, as described by the model, appears to have no limiting effect on the current predicted by the model until large positive voltages. Additionally, we observe that the ultrafast injection from the excited dye molecules limits the interfacial reactions that affect the DSC current.