No description available.

No description available.

The diploma thesis deals with the study of the behaviour of bidisperse MR fluids. The introduction gives brief research and analysis of previously published studies. In the main part of this thesis, the sedimentation properties of monodispersions and bidispersions are investigated influencing on the primary and secondary particles size, the ratio between the fractions, the total concentration of the particles dispersed in the MR fluid and the carrier fluid viscosity. The initialization sedimentation rate is used to assess sediment stability. Subsequently, MR samples are tested on a slit-flow rheometer, and flow curves are measured at different temperatures and in the presence of various magnetic fields intensities. The MR effect is evaluated by the yield stress. The study contains results describing the behaviour of investigated MR fluid samples.

The main task of this work was to compare the being used process fluids in mechanical engineering with a focus on polymer and additive fluids. Selected polymer and nanoadditive fluids were compared based on a thread forming test, during which different concentrations of individual fluids were tested. All data from experiments were evaluated, assessed in terms of their properties, and recommended for further practice.

The submitted thesis is focused on the development, optimization, testing and practical application of the new microextraction method called Bell Shaped Extraction Device assisted Liquid-Liquid Microextraction (BSED-LLME). The method is based on the application of a miniature bell-shaped extraction tool in which the extraction takes place, so that only minimal solvent losses can occur, and which allows a reproducible dosing and collection of a small volume of the extraction solvent. The BSED- LLME method was used to preconcentrate selected volatile and less volatile analytes from aqueous samples into organic solvents of a density lower than water. After the extraction, the analytes were determined by fast gas chromatography with flame ionization detection and gas chromatography with mass spectrometry. The statistical methods known as Design of Experiment (DOE) were used for determination of the optimal extraction conditions for BSED-LLME procedure. DOE is based on a mathematical description of the system and the prediction of the optimal setting of experimental parameters that may influence extraction efficiency. Factors such as extraction time, volume of extraction solvent, addition of sodium chloride (ionic strength), stirring rate and the diameter of the extraction vessel ect., have been tested....

This diploma thesis "Experiment with simple tools" is about preparation experiments made from object of daily use or different commercially available tools. Experiments are direct to fluid subject. Experiments are constructed to homemade use. Working students? sheets are prepared for these experiments. They are attached to this thesis. These students sheets serve as leading in independent work. Students after them can try experiment and brush subject up.

My Master thesis is focused on a tracer dilution technique in the well using automatic conductivity logging probes LTC Levelogger (Solinst co. Canada). The main aim of my thesis was to test the application conductivity meters LTC to track the movement of fluids in wells. Different set up were used moving probes with unmodified sensor slit, moving probes with modified sensor slit, probes measuring at fixed points, combined moving and fixed points probes and results were compared. 15 wells in quaternary and 11 wells in Bohemian Cretaceous Basin were measured, some of them repeatedly. The comparison of results indicate that the highest apparent flow velocity have probes with unmodified sensor slit. On the other hand fixed point probes indicate flow velocity, which is 40 - 50% lower at the same wells. The combination of the stable positioned probe LTC and the moving probe LTC has about 40% higher flow velocity than the rate of steady probe LTC placed in the well. The results also indicate that extremely slow velocity values (below approximately 0.02 m/day) can be measured only with LTC probes at fixed points. Modified probe slit was tested in the laboratory in plexi-glass tube using fluorescein and NaCl tracers. Unfortunately the modified geometry of measuring slit does not show distinctively better...

This diploma thesis investigates the accelerated sedimentation of the magnetorheological fuids (MRFs) using centrifuge. Experiments are carried out at room temperature as well as at higher temperatures (40°C, 60°C and 80°C). The development of the new improved measuring device for the sedimentation evaulation is described. Magnetic components of the device were designed using FEM analysis. Newly designed device is verified. To accomplish the experiments at the high temperatures the new heated chamber for experimental centrifuge is designed and constructed. In the next part of the work full experiment of the accelerated sedimentation is performed. At final the empirical model of the sedimetation velocity for various accelerations and temperatures is synthesized.

The diploma thesis contains a research part focused on turbocharger construction, engine lubrication system and turbocharger, basic physical properties of lubricating oils and hydrodynamics. The purpose of this thesis is to create analytical and CFD computational model of turbocharger lubrication system. Output pressures and the loss of specific energy are determined.

This master thesis deals with the basic problems of solar thermal systems, which are using heat transfer medium. At the beginning this thesis describes basic components of the solar system, especially their meaning and attributes. Further in the thesis are mentioned heat transfer liquids for commercial usage which are used in those systems, their basic properties and dependence on temperature. There is described the physical nature of liquid viscosity and also ways how to measure them. The same is for measurement of liquid density and thermal conductivity. At the end was made measurement of dynamic viscosity of heat transfer liquids for commercial usage at different temperatures. In practical part of the thesis were mixed samples of alternative heat transfer mediums. It was measured their thermal and physical attributes, like for example density, dynamic viscosity and coefficient of volumetric expansion. Each measurement was compared and evaluated.