The aim of this master project is to design a nzeb kindergarten and primary school in Škrdlovice. The building has three parts: kindergarten and primary school with 2 above–ground floors and basements are connected with a single canteen. The canteen has a flat extensive green roof, while the kindergarten and primary school have saddle roof. The kindergarten has two identical floors with playrooms, locker rooms, bed and toy storage, teacher’s office, and bathrooms. First floor of the primary school contains locker room, teacher’s’ offices, it classroom, afterschool centre, and toilets. Three classrooms, headmaster’s office, and toilets are in the second floor. The building is designed using Xella building system. The external load–bearing walls, slabs, and internal non–bearing walls are made of aerated concrete blocks. The internal load–bearing are made of lime–sand blocks. The building is insulated with non–fibrous mineral panels. The project includes design of lightning, HVAC, DHW, and photovoltaics systems. The project also includes a study of three structural details including 3D models in BIM software and their thermal assessment. The project was designed using BIM software Revit.

This master thesis deals with the taxation of a personal income and a corporation income. The theoretical part of the thesis describes the structural elements of taxes in conditions of the Czech Republic and characterizes the corporation income tax and the personal income tax. The practical part focuses on calculations of the corporation income tax and the personal income tax and a comparison of the employees and entrepreneurs taxation and a comparison of the taxation of the corporation income in 2009 - 2013.

The diploma thesis deals with the construction of a new sports center in Jeseník in the Olomouc Region. This work is aimed at elaborating project documentation for construction work. The building is completely basement, two-storey. The perimeter walls together with the ceiling structure are made up of the Porotherm masonry system. The roof is designed as a green vegetation roof on a monolithic reinforced concrete slab. The building is designed primarily for the maximum use and as a background of the local ski club taking into account all their needs and requirements.

This master´s thesis deals with the issue of the building from a clay. It is focused on defects and rehabilitations of these constructions. The introductory parts concerns with probable defects especially of clay buildings, furthermore with causes of the creation of defects, its depictions and the relevance. In the following part the methods of rehabilitation not only of clay buildings are presented. In this part the rehabilitative methods of foundation, vertical and wood constructions, which create mainly the structural support of the buildings, are described. In the second part, the structural and technical research of the current structure with farm part – barn is executed. The part of research is creation of the drawing documentation, description of disposition and structural and constructional solution of building, structural calculation of a part of construction, assessment of actual state of structure and prospective plan of proceeding and rehabilitation.

Thesis deals with proposal lay – out assembly for pneumatic cylinder. Assembly is proposed into separate workplace. Single step are described in those work according to which workplace assembly are put together, division pneumatic cylinder to single constructional insider division and operation on single workplace and description these workplace. Analysis proposal is implementation in the end.

The diploma thesis ‚Rubber Torsional Vibration Damper Of a Four-Cylinder Diesel Engine‘ covers all the development phases related to a design of a rubber damper for a specified engine. The individual phases of it are discussed in details throughout the thesis. At first, the construction plan of a crankshaft is given. The computational checks for torsional vibrations and forced torsional vibration are performed then. With regards to it there might be derived the basic parameters and dimensions of a rubber torsional vibration damper. The knowledge of them enables to prepare the constructional plan of a rubber torsional vibration damper. By using this damper construction plan the torsional displacements (deviations) and forced vibrations are calculated. Finally, a mechanical and thermal stress test of this damper is performed and a crankshaft production drawing is produced.

The thesis deals with the design of the experimental testing rig. Test rig is designed to measure NVH transmission parameters. First, basic knowledge of vibro-acoustic measurement is discussed. This is followed by an evaluation of the most commonly used power devices to derive real loads on measured gearboxes. In more detail, a back-to-back test rig is disassembled among other things. In the thesis are described two main components, which are composed of a connecting element and a test bench. Both components were optimized during the design due to their modal properties. Numerical modal analysis was performed in ANSYS Workbench software. The thesis also includes strength calculations performed using both numerical and analytical approaches. The indispensable result of the design work is the complete drawing documentation. Finally, measurements of vibrations and noise on the physically made connecting element assembly have been performed and subsequently evaluated.

This master‘s thesis is focused on the design of manipulator for crankshaft handling in flexible production lines. The first part describes the types of production lines and possible ways of inter-operative manipulation. With regard to the suitability of their use, a suitable variant is selected, which is then conceptually processed and verified by technical calculations. The final conclusion is the verification of the design in terms of safety. Part of the master‘s thesis is technical drawing documentation.

The master thesis is focused to design and realization of experimental equipment for researching of residual stress determination for specimen with non-uniform distribution stress along the depth. Literature search study of problematic was performed and it was used for elaboration of chapters about origin of residual stress, their classification and chapters about methods, which are used for measuring of residual stress and their determination. The following part explains the design of experimental equipment and stress-strain analysis of selected parts of this equipment. Then the final design of equipment is presented, including complete production drawings, and it’s explained final assembling of experimental equipment. Final chapter is devoted to examinable loading of specimen.

The community center in Ostrava - Kunčičky design in reflecting the specific social and material situation of the city. Creates new possibilities for the habitants and helps their integration and interaction. This design endeavors to naturally establish the existing church and rectory, not trying to compete them, but develop them. Important point of this project is also new village center, which is located right in front of the church and gets new definition and soundness. The project also solves the development of public amenities in relation of spiritual, social and everydays needs. It offers an insight into the real solutions to the problems and opportunities of the place in relation to the possibilities of the local parish. The project works with the this units: church, rectory, square, community center, community courtyard, multifunctional hall, house with services, sports facilities and meadow behind the church.