Stora Enso Kvarnsveden är ett pappersbruk lokaliserat vid Dalälven i Kvarnsveden. Bruket har för tillfället två producerande maskiner och detta arbete behandlar en av dem, vilken är PM12. På PM12 har man problem med oljeläckage i maskinens torkparti. Läckagen uppstår genom de lagerhus som finns för att bära upp torkpartiets valsar. I detta arbete har man undersökt vad läckagen beror på med fokus på dess lagertätningar. Syftet och målet med detta arbete har varit att utreda varför läckagen uppstår samt att generera koncept för att minska eller helt eliminera läckagen. Arbetet har innefattat diverse mätningar och utredningar för att komma till rätta med problemet. En litteraturstudie har genomförts för att identifiera felorsaker samt lösningar. Koncept har genererats utifrån studien samt de mätningar som utförts. Man har inte under arbetets gång helt kommit fram till vad läckagen beror på men man har kommit en bra bit på vägen. Förslag till fortsatt arbete har getts där det rekommenderas mer specifikt vilka typer av mätningar som bör genomföras samt de koncept man som bör bygga vidare på. / Stora Enso Kvarnsveden is a paper mill located at Dalälven in Kvarnsveden. The utility currently has two producing machines, and this study deals with one of them, which is PM12. At PM12 there is a problem with oil leaks in the machine's drying section. Leakage occurs through the bearing houses who are there to support the dryer's rollers. In this study, it has been investigated what the leakage is due to focusing on its bearing seals. The purpose of this study has been to investigate why leakage occurs and to generate concepts to reduce or eliminate leaks. The study has included various measurements and investigations to address the problem. A literature study has been conducted to identify causes and solutions. Concepts have been generated from the literature study as well as the measurements that have been taken. After this study it´s not fully realized why the leakage occurs, but it had come a long bit on the way. Proposals for continued work have been given, where it is recommended more specifically what kind of measurements that should be done and the concepts that should be further developed.

The diploma work is focused to evaluation of contemporary state of sealing system solution of high speed turbine engines in the world and, newly suggesting nontraditional design of labyrinth sealing lining for turbine side of small turbojet engine, including the production technology, technical-economic classification and experimental verification.

In this paper numerical flow calculations with respect to the annular gaps with added radial grooves normaly used on the spools of directional control valves were carried out. The impact of various annular gap geometries and radial grooves during variable pressure conditions, and while using different hydraulic fluids, on the flows through annular gaps were investigated for different flow regimes. Samples with different geometries and numbers of radial groves on the spool of the directional control valve were also made for the purpose of carrying out flow measurements. The two different hydraulic fluids that were used in the numerical simulations and for the flow measurements were a hydraulic mineral oil and tap water. The results of the numerical calculations for the different models of the radial grooves with axially symmetric geometries show their impact on the internal leakage with respect to three different regimes of flow. The results of the numerical calculations based on the use of a hydraulic oil show a trend that was established by the experimental investigation.

In this paper numerical flow calculations with respect to the annular gaps with added radial grooves normaly used on the spools of directional control valves were carried out. The impact of various annular gap geometries and radial grooves during variable pressure conditions, and while using different hydraulic fluids, on the flows through annular gaps were investigated for different flow regimes. Samples with different geometries and numbers of radial groves on the spool of the directional control valve were also made for the purpose of carrying out flow measurements. The two different hydraulic fluids that were used in the numerical simulations and for the flow measurements were a hydraulic mineral oil and tap water. The results of the numerical calculations for the different models of the radial grooves with axially symmetric geometries show their impact on the internal leakage with respect to three different regimes of flow. The results of the numerical calculations based on the use of a hydraulic oil show a trend that was established by the experimental investigation.