This thesis is concerned with kinetic characterisation of theinsertion compound LiMn2O4, which is used as positive electrodematerial in rechargeable lithium batteries. Three different typesof electrode configurations have been investigated, namely singleparticles, thin films and composite electrodes. Differentelectrochemical techniques, i.e. linear sweep voltammetry (LSV),electrochemical impedance spectroscopy (EIS), potential step, andgalvanostatic experiments were applied under various experimentalconditions. The majority of the experimental data were analysedby relevant mathematical models used for describing the reactionsteps of insertion compounds. It was concluded that a model based on interfacialcharge-transfer, solid-phase diffusion and an external iR-dropcould be fairly well fitted to LSV data measured on a singleelectrode system over a narrow range of sweep rates. However, itwas also found that the fitted parameter values vary greatly withthe characteristic length and the sweep rate. This indicates thatthe physical description used is too simple for explaining theelectrochemical responses measured over a large range of chargeand discharge rates. EIS was found to be a well-suited technique for separatingtime constants for different physical processes in the insertionand extraction reaction. It was demonstrated that the impedanceresponse is strongly dependent on the current collector used.According to the literature, reasonable values of theexchange-current density and solid-phase diffusion coefficientwere determined for various states-of-discharge, temperatures andelectrolyte compositions. Experiments were carried out in bothliquid and gel electrolytes. A method which improves thedistinction between the time constants related to thematerial’s intrinsic properties and possible porous effectsis presented. The method was applied to composite electrodes.This method utilises, in addition to the impedance responsemeasured in front of the electrode, also the impedance measuredat the backside of the electrode. Finally, the kinetics of a composite electrode was alsoinvestigated by in situ X-ray diffraction (in situ XRD) incombination with galvanostatic and potentiostatic experiments. Noevidence of lithium concentration gradients could be observedfrom XRD data, even at the highest rate applied (i.e. ~6C), thusexcluding solid-phase diffusion and also phase-boundary movement,as described by Fick’s law, as the ratelimiting step. <b>Key words:</b>linear sweep voltammetry, electrochemicalimpedance spectroscopy, potential step, in situ X-raydiffraction, microelectrodes, electrode kinetics, LiMn2O4cathode, rechargeable lithium batteries

<p>This thesis is concerned with kinetic characterisation of theinsertion compound LiMn2O4, which is used as positive electrodematerial in rechargeable lithium batteries. Three different typesof electrode configurations have been investigated, namely singleparticles, thin films and composite electrodes. Differentelectrochemical techniques, i.e. linear sweep voltammetry (LSV),electrochemical impedance spectroscopy (EIS), potential step, andgalvanostatic experiments were applied under various experimentalconditions. The majority of the experimental data were analysedby relevant mathematical models used for describing the reactionsteps of insertion compounds.</p><p>It was concluded that a model based on interfacialcharge-transfer, solid-phase diffusion and an external iR-dropcould be fairly well fitted to LSV data measured on a singleelectrode system over a narrow range of sweep rates. However, itwas also found that the fitted parameter values vary greatly withthe characteristic length and the sweep rate. This indicates thatthe physical description used is too simple for explaining theelectrochemical responses measured over a large range of chargeand discharge rates.</p><p>EIS was found to be a well-suited technique for separatingtime constants for different physical processes in the insertionand extraction reaction. It was demonstrated that the impedanceresponse is strongly dependent on the current collector used.According to the literature, reasonable values of theexchange-current density and solid-phase diffusion coefficientwere determined for various states-of-discharge, temperatures andelectrolyte compositions. Experiments were carried out in bothliquid and gel electrolytes. A method which improves thedistinction between the time constants related to thematerial’s intrinsic properties and possible porous effectsis presented. The method was applied to composite electrodes.This method utilises, in addition to the impedance responsemeasured in front of the electrode, also the impedance measuredat the backside of the electrode.</p><p>Finally, the kinetics of a composite electrode was alsoinvestigated by in situ X-ray diffraction (in situ XRD) incombination with galvanostatic and potentiostatic experiments. Noevidence of lithium concentration gradients could be observedfrom XRD data, even at the highest rate applied (i.e. ~6C), thusexcluding solid-phase diffusion and also phase-boundary movement,as described by Fick’s law, as the ratelimiting step.</p><p><b>Key words:</b>linear sweep voltammetry, electrochemicalimpedance spectroscopy, potential step, in situ X-raydiffraction, microelectrodes, electrode kinetics, LiMn2O4cathode, rechargeable lithium batteries</p>

Membrane transport processes underlie many purification technologies. The efficiency of a membrane separation process depends upon material throughput (flux), and the degree to which the membrane discriminates amongst species in the feed stock (selectivity). In a supported liquid membrane, flux may be enhanced by carrier molecules, which act as catalysts of translocation. Carrier molecules also confer selectivity, via differential molecular recognition of the substances in the feed stock. The effect of electrical potential on the flux and selectivity of carrier-containing supported liquid membranes is not well documented. We elected to study the effect of electrical potential on supported liquid membranes containing valinomycin, a potassium ionophore, and a calixarene ester, a sodium ionophore. In these systems, the open circuit membrane potential could be made positive or negative by the choice of anion. With both of these carriers, we observed that selectivity for potassium or sodium salts was dependent on the open circuit membrane potential. To confirm that electrical potential was responsible for the observed selectivity variance, we applied a potential across the membrane using a potentiostat. The applied potential created conditions for carrier-mediated electrodialysis, where oxidation and reduction reactions on either side of the membrane act as the driving force for transmembrane flux of charged species. In chronoamperometry experiments, we found that selectivity for potassium or sodium ion was dependent on the applied electrical potential. Subject to some constraints, selectivity and flux could be controlled by the application of positive or negative electrical potentials. Linear sweep voltammetry experiments allowed for the rapid prediction of the potential that must be applied to achieve optimal selectivity. We also found that membrane potential measurements, as well as the magnitude of current that flows in chronoamperometry experiments, could be interpreted to predict Eisenman and Hofmeister sequences. These results are novel, and await a convincing theoretical justification. The results also suggest that a separation technology could be developed around the idea of modulating selectivity with electrical potential. In this regard, carrier-mediated electrodialysis may be suitable for the sequestration of toxic or radioactive heavy metals, and a large number of carrier molecules for metal ions are currently known. The technique may also be suitable for separating organic molecules, such as high-value chiral pharmaceuticals. Supported liquid membranes are a useful research tool, but industrial applications may require a more stable membrane architecture. / Graduate

Master's thesis deals with new methods of preparing catalytic materials for positive electrode of an oxygen-hydrogen fuel cell and the influence of potassium permanganate or doping agent molar mass change on theirs attributes. Further it studies the use of proper measuring methods designed to qualify theirs attributes and the presentation of achieved results. In particular methods of linear sweep and cyclic voltammetry and the processing of data using Koutecky-Levich and Tafel plot and wave log analysis. Values of half-wave and onset potential and kinetic coefficient have been measured and calculated.