According to the 1 991 Annual Report of the Department of Health and Social Services of former Bophuthatswana, there were 364 reported malignant conditions found in women with cancer of the breast and cervix being the most prevalent. What causes great concern is t.he fact that patients present for the first time at health facilities during advanced stages of these diseases thus making the prognosis poor. Black patients in this study were found to present with cancer of the breast at an earlier age than their white counterparts. In addition to the above named problems, no facility exists for the treatment of cancer in the area of study and patients have to be referred to other areas. It was on the strength of the above observations that the researcher embarked upon this study to establish the effects of the diagnosis cancer and mastectomy on the victims. The aims of the study therefore were: to explore and describe the psycho-social effects of the diagnosis and treatment on Black women; develop guidelines for oncology nurses and doctors to assist with the adaptation of these patients to the diagnosis and treatment; and provide information that could lead to better training of oncology personnel as well as develop a proper support system to facilitate adjustment of the mastectomised patient to the disease and its treatment. Data were collected using the qualitative and quantitative approaches with individual in-depth interviews forming the main strategy. The findings revealed that the diagnosis cancer of the breast was equated with death among all respondents. The mastectomy added more stress for the patient, which was further compounded by chemo- and radiotherapy. The latter was described as causing more pain than the tumour itself. Problems experienced by the patients were reported to include: financial difficulties; general weakness; fear of recurrence and metastasis; concern for dependent children and fear of unemployment. All respondents in this study expressed the need for the formation of a voluntary care group, which could assist them with adaptation to the disease and its treatment. / Advanced Nursing Sciences / D. Lit. et Phil. (Advanced Nursing Sciences)

Essay I: Employment Security Agreements, which are elements of Swedish collective agreements, offer a unique opportunity to study very early job search counselling of displaced workers. These agreements provide individual job search assistance to workers who are dismissed due to redundancy, often as early as during the period of notice. Compared to traditional labor market policies, the assistance provided is earlier and more responsive to the needs of the individual worker. In this study, I investigate the effects of the individual counseling and job search assistance provided through the Employment Security Agreement for Swedish blue-collar workers on job finding and subsequent job quality. The empirical strategy is based on the rules of eligibility in a regression discontinuity framework. I estimate the effect for workers with short tenure, who are dismissed through mass-layoffs. My results do not suggest that the program has an effect on the probability of becoming unemployed, the duration of unemployment, or income. However, the results indicate that the program has a positive effect on the duration of the next job. Essay II: The well-known positive relationship between the unemployment benefit level and unemployment duration can be separated into two potential sources; a moral hazard effect, and a liquidity effect pertaining to the increased ability to smooth consumption. The latter is a socially optimal response due to credit and insurance market failures. These two effects are difficult to separate empirically, but the social optimality of an unemployment insurance policy can be evaluated by studying the effect of a non-distortionary lump-sum severance grant on unemployment durations. In this study, I evaluate the effects on unemployment duration and subsequent job quality of a lump-sum severance grant provided to displaced workers, by means of a Swedish collective agreement. I use a regression discontinuity design, based on the strict age requirement to be eligible for the grant. I find that the lump-sum grant has a positive effect on the probability of becoming unemployed and the length of the completed unemployment duration, but no effect on subsequent job quality. My analysis also indicates that spousal income is important for the consumption smoothing abilities of displaced workers, and that the grant may have a greater effect in times of more favorable labor market conditions. Essay III: Evidence from around the world suggest that individuals who are awarded disability benefits in some cases still have residual working capacity, while disability insurance systems typically involve strong disincentives for benefit recipients to work. Some countries have introduced policies to incentivize disability insurance recipients to use their residual working capacities on the labor market. One such policy is the continuous deduction program in Sweden, introduced in 2009. In this study, I investigate whether the financial incentives provided by this program induce disability insurance recipients to increase their labor supply or education level. Retroactively determined eligibility to the program with respect to time of benefit award provides a setting resembling a natural experiment, which could be used to estimate the effects of the program using a regression discontinuity design. However, a simultaneous regime change of disability insurance eligibility causes covariate differences between treated and controls, which I adjust for using a matching strategy. My results suggest that the financial incentives provided by the program have not had any effect on labor supply or educational attainment.

The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding. An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage. A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner. A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.   The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction. / civilingenjörsexamen

<p>The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding.</p><p>An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage.</p><p>A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner.</p><p>A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.</p><p> </p><p>The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction.</p><p> </p> / civilingenjörsexamen

1.Summary - review in English The above-mentioned work comprises of two basic issues that are connected together, namely commentary on Insurance Policy Act as general introduction into the field of insurance policies and consequent and special issue of legal expenses insurance interpretation. The basic meaning of it was to introduce not only the provisons concerning insurance policies, but also to show one of the insurance policies type in details, what could be hardly possible or satisfactory without preceding description of the Insurance Policy Act. Thus, complete summary of this work will be divided into two parts; first would be the part concerning Insurance Policy Act and second would be the part concerning legal expenses insurance. 1.1.Insurance Policy Act - Summary The first part of this work concerned, as mentioned above, the Insurance Policy Act, whereas my primary aim was to interpret provisions of this act that were worth it and point out namely on imperfections of the existing legislature. It wasn't and wouldn't be of any significant value just to copy and paste individual provisions of the act, therefore, this work aimed primarily on introduction of new ideas and as a basis for that served a confrontation with the actual wording and its interpretation, whereas plain consent with what was...