Spelling suggestions: "subject:"microhybrid"" "subject:"microhydration""
1 |
Design of a pump-as-turbine microhydro system for an abalone farmTeuteberg, B. H. 03 1900 (has links)
ENGLISH ABSTRACT: This document details the design process of a 97 kW microhydro system for Roman Bay Sea Farm in Gansbaai in the Western Cape Province of South Africa.
It contains a literature study of microhydro power, with a focus on the use of
Pump-as-Turbine technology and direct-drive systems. The literature study leads
to several possible concepts for the project, which are then evaluated and the
most suitable design is found to be a reverse running pump that powers a
different pump through a direct drive system. Experimental data from KSB is
used to test the accuracy of various correlations that can be used to generate
turbine-mode operation curves from pump curves. The final design parameters
for the complete system are then determined, and presented along with a cost benefit
analysis. / AFRIKAANSE OPSOMMING: Hierdie verslag dokumenteer die ontwerpsproses van ‘n 97 kW mikro hidro stelsel vir Roman Bay Sea Farm in Gansbaai in die Wes-Kaap van Suid Afrika. Dit
bevat ‘n literatuurstudie van mikro hidrokrag, met ‘n fokus op Pomp-as-Turbine
en direk-gekoppelde stelsels. Die literatuurstudie lei tot ‘n aantal moontlike
konsepte vir die projek wat dan evalueer word sodat die mees gepaste ontwerp
gekies kan word. Dit word gevind dat ‘n pomp wat verkeerd om hardloop en ‘n
ander pomp direk van krag voorsien die mees gepaste ontwerp is.
Eksperimentele data van KSB word gebruik om die akkuraatheid van verskeie
korrelasies te toets wat gebruik kan word om turbine-mode gedrag van pomp
kurwes te bepaal. Die finale parameters van die hele stelsel word dan bepaal en
word dan saam met ‘n koste-analise aangebied. / Centre for Renewable and Sustainable Energy Studies
|
2 |
Increasing the specific speed of simple microhydro propeller turbinesFuller, Adam Michael January 2011 (has links)
The late University of Canterbury civil engineering lecturer Peter Giddens developed a range of simple microhydro turbines, with publications from as early as the 1980s. He considered that a range of simple but well-designed turbines which covered the gamut of possible small sites would be more useful than any single turbine. He started with radial inflow turbines, then set about extending their range of applicability by increasing specific speed. That extension was continued by the research in this thesis, which aimed to produce a design with a minimum efficiency of 70 % at a specific speed of at least 600 (rev/min, kW, m). Achieving those targets would differentiate it from existing microhydro designs. In order to reach those performance targets, the volute, runner, and draft tube were examined through experiment and computational fluid dynamics models to characterize past designs and test the validity of their embodied assumptions. A prototype with a design specific speed of 650 was built and fully characterized by dynamometer testing.
Measurements of the outlet velocity distribution of two of Peter Giddens’s volutes confirmed that single tangential inlet volutes are not torque-free when certain geometric conditions are met; swirl increased through those volutes by 70 % or more depending on the design. A new overall turbine design was proposed, where axial flow enters the runner and swirling flows leaves it. This required the design of a novel volute. Through computational analysis, the effect of swirling flow entering the conical draft tube was shown to affect its pressure recovery: negatively for draft tubes with small angles, positively for larger angles. It was shown that the peak pressure recovery of an optimum draft tube was not likely to be improved upon by the use of swirl, and since there was uncertainty in the analysis, a conservative draft tube was specified for the prototype. A flat-bladed runner was designed for the prototype and computational modeling indicated its performance would be sensitive to small changes in flow angle. Despite that sensitivity — an intrinsic property of high specific speed runner velocity triangles — the computational model was shown to give good predictions of the runner flow characteristics, although not its effciency. Finally, a 1.2 kW prototype was built and achieved a peak net effciency of 64 % as defined by the American Society of Mechanical Engineers at a net head of 2.07 m, a flowrate of 94 L/s, and a runner shaft speed of 1670 rev/min, corresponding to a specific speed of 740. Maximum measured runner efficiency of 87 % also occurred at those conditions. Compared to existing designs, that performance extended the operational envelope of microhydro turbines considerably. A three-zone computational model of the entire prototype was assembled and trialled, but not validated.
It is concluded that for efficient high specific speed turbines, volute swirl characteristics must be known with confidence, as the volute sets the conditions at the leading edge for peak runner efficiency. A simple but efficient runner may be made using flat blades, showing the potential for this geometry even when made by limited workshops. Adding a free-vortex tangential velocity distribution to the inlet flow of a stalled conical draft tube may increase its pressure recovery, although it is not likely to exceed the best performance obtainable with axial inlet flow. Therefore taking measures to reduce the peak fluid velocity entering the draft tube could be more beneficial to overall performance than seeking outright improvements in draft tube pressure recovery.
|
3 |
Ballast-Free Variable-Speed Generation for Standalone and Grid-Connected Micro-Hydel Power PlantsJoseph, Rex January 2014 (has links) (PDF)
Concerns about climate change brought about by the increasing usage of fossil fuels has made it imperative to develop sustainable energy usage based on renewable sources. Micro-hydel plants are an important source of renewable energy that can be exploited to supply requirements of local loads in remote locations while operating as an isolated source, or the larger network when operating in grid connected mode. The focus of this research is to develop an alternative topology to the one currently in use in micro-hydel power plants. While existing plants are based on a ballast-controlled, fixed-speed, operator-supervised model, the proposed work introduces a ballast-free, variable-speed generator capable of unsupervised operation.
Conventional micro-hydel generators use o-the-shelf machines with the purported aim of reducing costs. They run at a fixed speed, maintaining constant electrical load by switch-ing a plant-situated ballast load to compensate for consumer load changes. Although the intention is to have a simplified control scheme and reduced costs, the conventional plants end up being expensive since the balance-of-system costs are increased. The plant re-quires supervision by a trained operator and frequent maintenance, failing which the reliability suers. The cost and maintenance reduction possible is analysed by comparing the proposed topology with a typical well designed conventional micro-hydel plant.
The proposed topology takes the characteristics of the turbine into account, and by running at variable speed, ensures that only as much power is generated as required by the consumer load. This eliminates the ballast load and associated problems present in conventional plants. The generator can be connected to the grid, if present, enabling the available power to be fully utilized.
The behavior of a hydraulic turbine operating at a fixed head and discharge rate with no flow control is analyzed. Based on the turbine characteristics, a generator topology is developed, which operates in a speed range dictated by the characteristics of the turbine. Continual supervision is unnecessary since the operation of the generator is within safe limits at all times. A simple emulator that can mimic the steady state and dynamic behaviour of the turbine is developed to test the proposed generator.
The two-machine wound rotor generator proposed has an auxiliary exciter similar to a conventional brushless alternator with the additional provision for bidirectional power transfer. The shaft mounted rotor side electronics facilitate brushless operation, and to-gether with the stator side controllers form an embedded system that does away with having to tune the plant in-situ. The control scheme is evaluated for expected perfor-mance in dierent operating modes.
The thesis also discusses an optimization of the synchronous speed of the generator with respect to the turbine characteristics. This minimizes the bidirectional slip power transfer requirements of the rotor side converters and leads to the lowest rating for the auxiliary machine. The proposed generator can then operate like a conventional synchronous gen-erator in the grid connected mode with a simplified control scheme.
|
Page generated in 0.0423 seconds