<p>Active secondary suspension in trains has been studied for a number of years, showing promising improvements in ride comfort. However, due to relatively high implementation and maintenance costs, active technology is not being used in service operation to a large extent. The objective of this study is to develop an active lateral secondary suspension concept that offers good ride comfort improvements and enables centring of the carbody above the bogies when negotiating curves at unbalanced speed. Simultaneously, the active suspension concept should be a cost-effective solution for future series production. The thesis consists of an introductory part and three appended papers.</p><p>The introductory part describes the concept of active secondary suspension together with different actuator types and control methods. Further, the present simulation model and applied comfort evaluation methods are presented. The introductory part also comprises a summary of the appended papers, an evaluation of track forces and suggestions for further work.</p><p>Paper A presents the initial development of an active lateral secondary suspension concept based on sky-hook damping in order to improve vehicle dynamic performance, particularly on straight tracks. Furthermore, a Hold-Off-Device (HOD) function has been included in the suspension concept in order to centre the carbody above the bogies in curves and hence avoid bumpstop contact. Preparatory simulations as well as the subsequent on-track tests in the summer of 2007 showed that the active suspension provides improved passenger ride comfort and has significant potential to be a cost-effective solution for future implementation.</p><p>In Paper B, measurement results from on-track tests performed in 2008 are presented. The active secondary suspension concept was slightly modified compared to the one presented in the first paper. One modification was the implementation of a gyroscope in order to enable detection of transition curves and to switch off the dynamic damping in these sections. Ride comfort in the actively suspended carbody was significantly improved compared to that in the passively suspended car. The satisfactory results led to implementation of the active suspension system in long-term tests in service operation in the beginning of 2009.</p><p>In Paper C, a quarter-car model in MATLAB has been used to investigate a more advanced control algorithm: <em>H</em>_∞ instead of sky-hook. <em>H</em>_∞ control provides more flexibility in the design process due to the possibility to control several parameters. In particular, this is done by applying weight functions to selected signals in the system. When comparing the two control strategies through simulations, the results show that <em>H</em>_∞ control generates similar carbody accelerations at the same control force as sky-hook; however, the relative displacement displacement is somewhat lower.</p>

More than 50 percent of the land area of the Nordic countries Finland, Norway, and Sweden are covered by dense forests and they are among the most important producers of forest products in the world. Forestry in these countries is based on sustainable management principles – reforestation follows harvesting. Furthermore, increasing demands for more gentle techniques and technologies with less negative impact on the environment ask for development and implementation of new processes and new machine solutions. The increasing interest in developing forest management approaches that are based on gentleness to the environment requires better understanding of the interaction between the forestry machines and the terrain in the harvesting process. / <p>QC 20150827</p> / Gentle Forest Machines

Active secondary suspension in trains has been studied for a number of years, showing promising improvements in ride comfort. However, due to relatively high implementation and maintenance costs, active technology is not being used in service operation to a large extent. The objective of this study is to develop an active lateral secondary suspension concept that offers good ride comfort improvements and enables centring of the carbody above the bogies when negotiating curves at unbalanced speed. Simultaneously, the active suspension concept should be a cost-effective solution for future series production. The thesis consists of an introductory part and three appended papers. The introductory part describes the concept of active secondary suspension together with different actuator types and control methods. Further, the present simulation model and applied comfort evaluation methods are presented. The introductory part also comprises a summary of the appended papers, an evaluation of track forces and suggestions for further work. Paper A presents the initial development of an active lateral secondary suspension concept based on sky-hook damping in order to improve vehicle dynamic performance, particularly on straight tracks. Furthermore, a Hold-Off-Device (HOD) function has been included in the suspension concept in order to centre the carbody above the bogies in curves and hence avoid bumpstop contact. Preparatory simulations as well as the subsequent on-track tests in the summer of 2007 showed that the active suspension provides improved passenger ride comfort and has significant potential to be a cost-effective solution for future implementation. In Paper B, measurement results from on-track tests performed in 2008 are presented. The active secondary suspension concept was slightly modified compared to the one presented in the first paper. One modification was the implementation of a gyroscope in order to enable detection of transition curves and to switch off the dynamic damping in these sections. Ride comfort in the actively suspended carbody was significantly improved compared to that in the passively suspended car. The satisfactory results led to implementation of the active suspension system in long-term tests in service operation in the beginning of 2009. In Paper C, a quarter-car model in MATLAB has been used to investigate a more advanced control algorithm: H∞ instead of sky-hook. H∞ control provides more flexibility in the design process due to the possibility to control several parameters. In particular, this is done by applying weight functions to selected signals in the system. When comparing the two control strategies through simulations, the results show that H∞ control generates similar carbody accelerations at the same control force as sky-hook; however, the relative displacement displacement is somewhat lower.

One way to make rail vehicles a competitive means of transportation is to increase running speed. However, higher speeds usually generate increased forces and accelerations on the vehicle, which have a negative effect on ride comfort. With conventional passive suspension, it may be difficult to maintain acceptable passenger comfort. Therefore, active technology in the secondary suspension can be implemented to improve, or at least maintain, ride comfort at increased vehicle speeds or when track conditions are unfavourable. This thesis describes the development of an active secondary suspension concept to improve ride comfort in a high-speed train. Firstly, an active lateral secondary suspension system (ALS) was developed, including dynamic control of the lateral and yaw modes of the carbody. Furthermore, quasi-static lateral carbody control was included in the suspension system in order to laterally centre the carbody above the bogies in curves at high track plane acceleration and hence to avoid bumpstop contact. By means of simulations and on-track tests, it is shown that the ALS system can offer significant lateral ride comfort improvements compared to a passive system. Two different control strategies have been studied—the relatively simple sky-hook damping and the multi-variable H∞ control—using first a quarter-car and then a full-scale vehicle model. Simulation results show that significant ride comfort improvements can be achieved with both strategies compared to a passive system. Moreover, H∞ control in combination with the carbody centring device is better at reducing the relative lateral displacement in transition curves compared to sky-hook damping. Secondly, an active vertical secondary suspension system (AVS) was developed, using simulations. Dynamic control of the vertical and roll modes of the carbody, together with quasi-static roll control of the carbody, show significant vertical ride comfort improvements and allow higher speeds in curves. Further, the AVS system compensates for negative ride comfort effects if the structural stiffness of the carbody is reduced and if the vertical air spring stiffness is increased. Finally, the two active suspension systems (ALS and AVS) were combined in simulations. The results show that both lateral and vertical ride comfort is improved with the active suspension concept at a vehicle speed of 250 km/h, compared to the passive system at 200 km/h. Further, active suspension in one direction does not affect the other direction. The ALS system has been included in two recent orders comprising more than 800 cars. / QC 20111205 / Gröna Tåget

Electric buses often have batteries installed on the roof structure to have a better space utilization. This increases the height of the centre of gravity of the vehicle, affecting its roll stability. The existing vehicle setup uses an anti-roll bar to provide the roll stiffness. However, increasing the roll stiffness of the anti-roll bar for providing the required roll stability of an electric bus is limited due to the increase in weight of the anti-roll bar, its material properties and the design constraints. An alternate for the air suspension system is identified through a literature study. The identified system, an interconnected hydro-pneumatic suspension, is modelled analytically and compared to the air spring system. Multi-body simulations are performed to understand the roll performance.\par The thesis work also estimates the system's energy efficiency, and the feasibility of packaging the system within the existing vehicle architecture is studied in CAD software. The roll gradient of the vehicle is shown to improve compared to the existing air-spring system. The study also find that implementation of hydraulic-interconnected system can result in reduction of the unsprung mass of the vehicle. / Elektriska bussar har ofta batterier installerade på takkonstruktionen för att få ett bättre utrymmesutnyttjande. Detta ökar fordonets tyngdpunktshöjd och påverkar dess krängstabilitet. Den befintliga fordonskonfigurationen använder en krängningshämmaren tillsammans med luftfjädrar för att ge den krängsstabilitet som krävs. Men att öka krängstyvheten hos krängningshämmaren för att ge den nödvändiga krängstabilitet hos en elektrisk buss är begränsad på grund av ökningen av vikten av krängningshämmaren, dess materialegenskaper och konstruktionsbegränsningar. Ett alternativ till luftfjädringssystemet identifieras genom en litteraturstudie. Det identifierade systemet, ett sammanlänkat hydro-pneumatiskt fjädringssystem, modelleras analytiskt och jämförs med luftfjädringssystemet. Multibody-simuleringar utförs för att förstå fordonets krängprestanda. par Avhandlingsarbetet uppskattar också systemets energieffektivitet och möjl-igheten att paketera systemet inom den befintliga fordonsarkitekturen studeras i CAD-programvara. Fordonets krängningsgradient har visat sig förbättras jämfört med det befintliga luftfjädringssystemet. I studien konstateras också att införandet av hydrauliskt sammankopplade system kan leda till en minskning av fordonets ofjädrade massa.

Due to the increase in demand on freight transportation it becomes necessary to avoid delays to ensure that the goods reach its destination on time. The main factors causing disturbances in the traffic on the mainline is the breakdown of vehicles mainly due to damaged wheels. The damaged wheels are identified through the wheel-rail impact force measurements provided by the wheel impact load detectors (WILD). This calls for the optimal schedule of maintenance of wheelsets and wagons in general. During the maintenance, the officials manually check for defective wheels and the exchange of wheelsets is performed based on the type of damage. The classification of wheel damages plays a vital role in providing ease of damage identification and insights to deduce a strategy for wheelset exchange. In this study, an attempt to classify the damaged wheelsets is done by analysing the wheel-rail impact force data from the wayside detectors. The data from the detectors are acquired from PredgeAB, a Luleå based startup pioneering in providing decision support on optimal maintenance schedules and predictive maintenance of rail wheels. Through their detection and prediction solutions it was observed that of all the wheels marked as damaged by the detectors 10% were undamaged. The source of the deviation in the impact force readings could help Predge make better estimations in damage detection and prediction. In this study, the sources contributing to the deviation is studied using multi-body simulations in GENSYS. A new method for modelling wheel damage is developed to overcome the shortcomings of the software. The findings of this study can then be used appropriately to make classifications of wheel damages. / På grund av den ökade efterfrågan på godstransporter är det nödvändigt attundvika förseningar för att säkerställa att varorna når sin destination i tid. Deviktigaste faktorerna som orsakar störningar i trafiken på huvudlinjen är stopp ispår av fordon, främst på grund av skadade hjul. De skadade hjulen identifierasmed hjälp av mätningar av slagkraft mellan hjul och spår som tillhandahållsav hjulbelastningsdetektorer (WILD). Detta kräver ett optimerat schema förunderhåll av hjulsatser och vagnar i allmänhet. Under underhållet kontrollerartjänstemännen manuellt för defekta hjul och utbytet av hjulsatser utförs baserat på typen av skada. Klassificeringen av hjulskador spelar en viktig roll närdet gäller att underlätta identifiering av skador och ge insikt för att bedöma enstrategi för hjulbyte. I den här studien görs ett försök att klassificera de skadade hjulsatserna genom att analysera data från slagkraften mellan spår ochhjul från detektorer. Uppgifterna från detektorerna hämtas från PredgeAB, enLuleå-baserad uppstartsbolag som är pionjärer för att ge beslutsstöd om optimala underhållsscheman och prediktivt underhåll av järnvägshjul. Genom sinadetekterings- och prediktiva lösningar observerades att 10% av alla hjul märktasom skadade av detektorerna var oskadade. Källan till avvikelsen i slagkraftavläsningarna kan hjälpa Predge att göra bättre uppskattningar när det gällerupptäckning och förutsägelse av skador. I den här studien studeras de källorsom bidrar till avvikelsen med simuleringar av flera kroppar i GENSYS. En nymetod för modellering av hjulskador har utvecklats för att övervinna programvarans brister. Resultaten av denna studie skulle kunna användas på lämpligtsätt för att göra klassificeringar av hjulskador.