Södra DuraPulp is a relatively new eco-composite, made from natural wood fibers and polylactic acid (PLA), which comes from corn starch. Until now, there are only few applications for DuraPulp, mainly in the area of design. To find new fields of application, more knowledge about its mechanical material properties are of great interest.This study deals with characterizing the mechanical properties of DuraPulp in an analytical way by means of micromechanical modelling and evaluation with help of Matlab. The mechanical properties for PLA were taken from scientific literature. Not all properties of the wood fibers could be found in literature (particularly Poisson’s ratios were unavailable). Therefore, they partly had to be assumed within reasonable boundaries. These assumptions are later validated regarding their influence on the final product.Figures and tables were used to present and compare the in- and out-of-plane E-Moduli, shear moduli and Poisson’s ratios of DuraPulp. The calculated in-plane E-Moduli were then compared to those obtained from an earlier study, where DuraPulp was tested in tension. The results showed that experimental and analytical values are very similar to each other. / Södra DuraPulp är en relativt ny eco-komposit, tillverkat av naturliga trä fibrer och polylactic syra som kommer från majsstärkelser. I dagsläget finns det få användningsområden för DuraPulp, huvudsakligen används det inom design. För att expandera användningsområdet behövs det mer kunskaper angående de mekaniska egenskaperna för materialet. Studien handlar om att karakterisera de mekaniska egenskaperna för DuraPulp på ett analytiskt sätt i form av mikro-mekanisk modellering och evaluering med hjälp av Matlab. De huvudsakliga mekaniska egenskaperna för PLA kunde hämtas från flera vetenskapliga källor, men de motsvarande mekaniska egenskaperna för fibrer kunde inte alla valideras. Delvis antogs dem i rimliga gränser och deras inverkan validerades med hjälp av en parameter studie.Figurer och tabeller användes för att presentera och jämföra in- och ut-plan E-Moduler, skjuvmoduler och tvärkontraktionstalen av DuraPulp. De beräknade in-plan E-modulerna för DuraPulp jämfördes med motsvarande E-moduler från en tidigare studie där DuraPulp genomgick dragtest. Resultatet visade att analytiska och experimentella värden överensstämmer bra med varandra.

Flax fibers, along with a number of other natural fibers, are being considered as an environmentally friendlier alternative of synthetic fibers in fiber-reinforced polymer composites. A common feature of natural fibers is a much higher variability of mechanical properties. This necessitates study of the flax fiber strength distribution and efficient experimental methods for its determination. Elementary flax fibers of different gauge lengths are tested by single fiber tension in order to obtain the stress-strain response and strength and failure strain distributions. The applicability of single fiber fragmentation test for flax fiber failure strain and strength characterization is considered. It is shown that fiber fragmentation test can be used to determine the fiber length effect on mean fiber strength and limit strain. The effect of mechanical damage in the form of kink bands and of diameter variability on the strength of elementary flax fibers is considered. Stiffness and strength under uniaxial tension of flax fiber composites with thermoset and thermoplastic polymer matrices are studied. The applicability of rule of mixtures and orientational averaging based models, developed for short fiber composites, to flax reinforced polymers are evaluated. Both the quasi-static and time dependent mechanical properties of flax fiber/thermoplastic starch based composites are analyzed. The effect of temperature and relative humidity is investigated. It is found that microdamage accumulation in this type of composites is not significant. Results show that the composite elastic modulus and failure stress are linearly related to the maximum stress reached by the matrix in tensile tests. Simple material models are suggested to account for the observed nonlinear viscoelasticity and viscoplasticity. / Godkänd; 2009; 20091029 (edgspa); DISPUTATION Ämnesområde: Polymera konstruktionsmaterial/Polymeric Composite Materials Opponent: Docent Kristofer Gamstedt, Kungliga Tekniska Högskolan, Stockholm Ordförande: Docent Roberts Joffe, Luleå tekniska universitet Tid: Onsdag den 9 december 2009, kl 10.00 Plats: E 231, Luleå tekniska universitet