The common objective of this project is implementation of software defined radio (SDR) into FPGA. The text contains review and comparison of several hardware concepts intended for SDRs implementation then the methods for digital implementation of various components of radios as the filters, mixers and others are mentioned. Part of the text introduces used hardware platform and describes software support for designing, simulations and implementation into hardware. Significant part of project describes complex of external hardware components as filter, amplifier and control panel designed and built within the project realization. But the main part of project demonstrates design of the software solution of radio receiver. There is specified architecture of radio for FM broadcast receiving, next the more complex systems with carrier recovery algorithm are presented. These systems are able to work with AM, BPSK and QPSK modulations. It is possible to implement all these receivers into hardware and verify their operation. The practical laboratory theme has been outlined within the project run.

This Master’s thesis is focused on the design and structural analysis of load-bearing structure of a multipurpose hall that is strained by the permanent load, working load and climatic load. The hall has the shape of an elliptical dome. Maximum margin of the structure is 60,0m and maximum height is 18,0m. Main carrier elements of the structure are radially arranged curved beams made of glued laminated timber, class SA(GL24).

This master´s thesis elaborates a project documentation of sports rehabilitation center in Brno–Bystrc. The building object is four-storeyed and a partial basement. On the basement floor there is a pool with sauna, gym and fitness with support to assist for all activities offered. On the ground floor there is an entrance, reception for accommodation, restaurant and kitchen for the restaurant. The 2nd overground floors is determined by the rehabilitation clinic. On the grand and overground floor are designed sanitary appliances for the restaurant and patient surgeries. There are projected 9 apartments for weekend accommodation. Apartments allow access to the terrace. Foundations are made strip foundations. The building object is bricked and insulated with ventilated facades. Load bearing structure of the roof create roof trusses.

Dizertační práce je zaměřena na softwarově definované přijímače určené k úzkopásmové družicové komunikaci. Komunikační kanály družicových spojů zahrnujících komunikaci s hlubokým vesmírem jsou zatíženy vysokými úrovněmi šumu, typicky modelovaného AWGN, a silným Dopplerovým posuvem signálu způsobeným mimořádnou rychlostí pohybu objektu. Dizertační práce představuje možné postupy řešení výpočetně efektivní digitální downkonverze úzkopásmových signálů a systému odhadu kmitočtu nosné úzkopásmových signálů zatížených Dopplerovým posuvem v řádu násobků šířky pásma signálu. Popis navrhovaných algoritmů zahrnuje analytický postup jejich vývoje a tam, kde je to možné, i analytické hodnocení jejich chování. Algoritmy jsou modelovány v prostředí MATLAB Simulink a tyto modely jsou využity pro ověření vlastností simulacemi. Modely byly také využity k experimentálním testům na reálném signálu přijatém z družice PSAT v laboratoři experimentálních družic na ústavu radioelektroniky.

The thesis contains the main part of the building and technological project storey car park on the Panenská street in Brno. There is prepared a technical report on the structural and technological project studies the implementation of major technological stages, coordinating construction situation with broder relations roadways, time and financial plan construction, project construction site, design of building machines and mechanisms, the schedule of the main building structure, a plan for securing material resources for monolithic construction, technological regulation for the implementation of horizontal bearing structures, inspection and test plan for horizontal structure, a manual for use of the parking building and an itemized budget.

Master’s thesis is based on analysis and design of a load bearing structure of an mountains hotel. Mountain hotel schould be realized in the village Vernirovice in Šumperk district. The proposed structure is formed 4th floors. In 1.NP is a restaurant, a sports and wellness center. In 2.NP in the right side is situated the swimming pool. In 2 to 4 floor are located rooms. This structure is supported with a strip footing made of reinforced concrete. The main load-bearing elements in the vertical direction are in 1.NP reinforced concrete walls and columns, the upper floors bearing masonry walls of ceramic blocks THERM. The inner support walls are 300 mm thick, outside support walls are 400 mm thick. Floors are constructed of carrying plates with girders above the larger openings. These plates and girders are made of reinforced concrete. In the 2 floor are beams with the span of 8,8 m. These girders are designed of prestressed concrete cause the large loads. Individual levels are connected with monolithic concrete staircases. Around the middle of the building is a monolithic reinforced concrete elevator shaft. The highest elevation above grade level is 16 m. The thesis also deals with relevant drawing documentations for chosen parts of construction.The building is located in the ski area VI and IV wind areas.

The aim of this master’s project is to develop project documentation of a new-built mountain hotel in Ostružná. This hotel is near the ski area Ramzová in Jeseníky. Foundation of my building is from ground reinforced concrete slab. My building is supported by clay block load-bearing walls and clay non-load bearing walls. Exterior building envelope is designed as an aluminum shingle ventilated facade. The slabs are from reinforced concrete. The roofs of this designed building are two, first is pitched roof with insulation over rafters and second is intensive green warm flat roof. This project contains HVAC concept, photovoltaic panel concept, heating concept in technical equipment of building part. The third part of my master’s project is energy assessment for the building.

Master thesis is focused on design of steel roofing structure of sports hall. Construction is located in town of Jihlava. Proportions and disposition are in accordance of assignment of master thesis. The proportions are 40m x 60m, the height of structure is approximately 15m. Two versions of roof structure were designed – truss beam with shape of lentil and double reverse truss girders (girland truss). These versions were tentatively analyzed and designed for the main bearing members. Afterwards both of the versions were appraised and one of the versions was chosen for detailed treatment. It means there was attention focused on design of important details, creating of drawing documentation and technical report, all in the range of thesis supervisor. The valid Eurocodes were used.

The content of the diploma thesis is the processing of a constructive technological project of a business incubator. The objective of this constructive technological project is to approach the construction process in the framework of the study of the implementation of the main technological stages, which closely follows the project of the site construction equipment with suitable layout of its construction, as well as the design of suitable machinery mechanisms for realization of the main building. Part of the project is also to determine the timeliness of work, financial and material management, and technological regulations for implement selected activities, taking into account the quality control and planning of their implementation. The whole construction process is completed in the final part of the diploma thesis on the solution of the occupational health and safety issues.

utilization of current structures, concrete buildings, system of concrete buildings T06B, spank, portative parts of the structure, structure modifications, model of the solution