This master’s thesis first deals with the theory concerning induction motor. It briefly desbribes the construction of three-phase induction motors, the generation of tractive force, power flow with loss distribution and also torque characteristic. In the next part an analytical calculation of the parameters of equivalent circuit for an existing induction motor with known dimensions is performed. After the calculation it is possible to find out the rated parameters of the motor, which makes it possible to further compare results with the values obtained by other methods. The next step was to create a model of the motor in RMxprt program, which is later also translated to ANSYS Maxwell 2D model. Simulations were carried out in both interfaces. As the next step the results obtained by the three methods are compared with measured values and also evaluated. The final part of the thesis focuses on the optimization of the magnetic circuit for higher frequencies. Efficiency of the modified induction motor is examined for higher frequencies using RMxprt Optimetrics and this procedure is performed for both default and alternative electrical steel materials.

The thesis describes problematics of synchronous motor with permanent magnets. The design is provided by analytic and empiric procedures. The great accent is placed on the description of the magnetic circuit of the motor. The finite element method analysis of designed motor is performed subsequently. The main target of this thesis is to find the way, how the ferrite permanent magnet should be used in synchronous motor.

This thesis deals with a design of an electrical drive for a sliding side door. Goal of the thesis is to design of a frequency converter for an asynchronous motor with a gearbox. In the first part, the power supply for the freqency converter is solved in form of a single phase rectifier. Power section is solved by an integrated module IKC10H60GA manofactured by Infineon. The control board is provided with circuits for communication between the processor and the power section. Auxiliary power supply is designed as a fly - back converter. The drive of the converter is realized by STM32 Nucleo - 64 board. The design of the converter and drive algorithm are described in detail.

This diploma thesis deals with design of DC/DC converter which will be used in one-phase inverter powered from batteries. Required parameters are output power of 100 W, input voltage of 24 V and output voltage of 350 V. In the first part is briefly discussed used topology of flyback converter. In the next part is designed impulse transformer with a request to design impulse transformer as small as possible. Thesis continues with draft of power components placed on primary and secondary side of converter. In this thesis is part about limitation of voltage overshoot at turn off transistor. Next part of this thesis deals with the design of control circuits using an integrated circuit from the UC384x family. Thesis continues with the production and debugging of the converter. At the end of this thesis are measurements confirming the correctness of the proposed design.

This diploma thesis deals with analysis of function and subsequent construction of a quasi-resonant DC / DC converter 300 V / 50 V for an output of about 1.5 kW. The aim of this work is to test and describe the behavior of an experimental converter at various operating parameters. In the theoretical part, resonant circuits are described, as well as our connection of the resonant converter. Based on the used topology and the simulated behavior of the converter, the individual components of the power circuit and its control and excitation circuit are designed in Chapters 4 and 5. The sixth chapter deals with the construction and testing of the converter, including a description of its behavior. The last chapter contains technical documentation.

Před necelými dvaceti lety byl představen nekonvenční přístup k implementaci multifunkčních obvodů, tzv. polymorfní elektronika. Polymorfní elektronika umožňuje implementovat jedním obvodem dvě nebo více funkcí, přičemž aktuálně funkce závisí na stavu okolního prostředí obvodu. Klíčovými komponentami takových obvodů jsou polymorfní hradla. Od představení konceptu polymorfní elektroniky bylo publikováno několik desítek polymorfních hradel. Parametry většiny z nich však neumožňují jejich využití v reálných aplikacích. Bez dostatečného množství polymorfních hradel s dobrými parametry však nejspíše zůstane v aplikacích založených na multifunkčním chování nebo rekonfiguraci konvenční elektronika preferována před tou polymorfní. Tato disertační práce představuje nový přístup k polymorfní elektronice. Je založen na hradlech, jejichž funkce závisí na polaritě napájecích přívodů. Cílem této disertační práce je ukázat, že takový přístup umožňuje navrhnout hradla s výrazně lepšími parametry. Aby bylo možné systematicky navrhovat na úrovni tranzistorů takováto hradla, byla navržena evoluční metoda založená na kartézském genetickém programování (CGP). To umožnilo navrhnout několik sad efektivních polymorfních hradel založených jak na konvenčních MOSFET tranzistorech, tak na double-gate ambipolárních tranzistorech. Z těchto sad hradel byla vytvořena knihovna, která je v současné době volně dostupná pro ostatní vědce. Dále byla v této práci navržena řada složitějších obvodů založená na navržených hradlech. Na různých úrovních návrhu obvodů (hradla, RTL, cílová aplikace) je pak ukázáno, že navrhovaný polymorfismus na úrovni hradel představuje velké výhody v porovnání s předchozí generací polymorfních hradel, ale může být také konkurenceschopný nebo výrazně lepší než konvenční řešení takovýchto obvodů.

In this thesis, an evolutionary system for searching quantum operators in the form of unitary matrices is implemented. The aim is to propose several representations of candidate solutions and settings of the evolutionary algorithm. Two evolutionary algorithms were applied: the genetic algorithm and evolutionary strategy. Furthermore, a method of generating a unitary matrix is presented which is used for the first time for this task. This method is in some aspects better than the previous ones. Finally, a comparison of all used techniques is shown in experiments.

Tato diplomová práce se zabývá problematikou plašení ptáků a jejich humánního plašení pomocí laserů. Práce také pojednává o bezpečnosti laserů, problému řídicího obvodu laserových diod, kolimaci svazku a jeho rozšíření tak, aby výstupní výkon paprsku nepřekročil maximální hodnotu výstupního výkonu laseru třídy 2M.

The master thesis is focused on a remanent magnetism of electromagnets of DC contactors. In the first part of the thesis deals with the formation of a magnetic field in different kinds of materials, description of their magnetization and sorting. The next part is focused on the principle and history of an electromagnet. Negative effects and remanent induction of the contactor are described in the end of the theoretical part. The second part is a practical part. First, the reaction times were measured on a pair of DC contactors. Using the obtained data, an electronic circuit was designed to minimize the difference in switching times of the given DC contactors.

The main idea is focused on the diagnostics of a specific hydraulic system, i.e. sensing the physical quantities of the hydraulic circuit with a tank and a centrifugal pump driven by an asynchronous motor. It is a system of pipes connected to the pump, where due to its work it creates a water flow and a pressure increase. In practice, this issue is also addressed in the energy and nuclear industries. Primary circuits in some cases cannot be designed or modified to be able measure locally the pressure value. It is necessary to measure this quantity indirectly - from the motor currents. The main idea of the work is to diagnose the system by an indirect method - specifically to detect the state of the hydraulic circuit (pressure, flow) from the values that we are able to measure and detect damage in advance. In the second part of the thesis is the application of the parts of a specific hydraulic system in the simulation environment MATLAB Simulink. The model of the hydraulic circuit contains mathematical-physical relations that simulate the course of the mentioned experiment. The results of the simulation are compared with the results of the experiment. The model also investigates the simulation of a fault condition, when we supply pressure pulsations to the hydraulic circuit. It is these changes in the hydraulic part that affect the characteristics of the pump and the asynchronous motor, so we are able to diagnose this system.