The increasing demand for energy and the increased depletion rate of nonrenewable energy resources call for research on renewable alternatives. Mapping the availability of these resources is an important step for development of energy conversion projects. For this purpose, the wave power potential along the Atlantic coast of the southeastern USA, and the tidal stream power along the coast of Georgia are investigated in this study. Wave power potential is studied in an area bounded by latitudes 27 N and 38 N and longitudes 82 W and 72 W (i.e. North Carolina, South Carolina, Georgia, and northern Florida). The available data from National Data Buoy Center wave stations in the given area are examined. Power calculated from hourly significant wave heights and average wave periods is compared to power calculated using spectral wave energy density. The mean power within 50 km of the shore is determined to be low, whereas higher power is available further offshore beyond the 3500 m contour line. The tidal stream power potential along the coast of the state of Georgia is evaluated based on the NOAA tidal predictions for maximum tidal currents and three dimensional numerical modeling of the currents with Regional Ocean Modeling System (ROMS). The modeling results are validated against the available measurements. This region has low to moderate average tidal currents along most of the coast, but with the possibility of very strong local currents within its complex network of tidal rivers and inlets between barrier islands. Tidal stream power extraction is simulated with a momentum sink in the numerical models at the estuary scale to investigate effect of power extraction on the estuarine hydrodynamics. It is found that different power extraction schemes might have counterintuitive effects on the estuarial hydrodynamics and the extraction efficiency. A multi-criteria method that accounts for the physical, environmental and socioeconomic constraints for tidal power conversion schemes is proposed to select favorable locations and to rank them according to their suitability. For this purpose, the model results are incorporated into a Geographical Information System (GIS) database together with other geospatial datasets relevant to the site selection methodology. The methodology is applied to the Georgia coast and the candidate areas with potential are marked.

No description available.

Thesis (Ph.D.)--Aberdeen University, 2009. / Title from web page (viewed on July, 1 2009). Includes bibliographical references.

Ocean energy research has grown in popularity in the past decade and has produced various designs for wave energy extraction. This thesis focuses on the performance analysis of a uni-directional impulse turbine for wave energy conversion. Uni-directional impulse turbines can produce uni-directional rotation in bi-directional flow, which makes it ideal for wave energy extraction as the motion of ocean waves are inherently bi-directional. This impulse turbine is currently in use in four of the world’s Oscillating Wave Columns (OWC). Current research to date has documented the performance of the turbine but little research has been completed to understand the flow physics in the turbine channel. An analytical model and computational fluid dynamic simulations are used with reference to experimental results found in the literature to develop accurate models of the turbine performance. To carry out the numerical computations various turbulence models are employed and compared. The comparisons indicate that a low Reynolds number Yang-shih K-Epsilon turbulence model is the most computationally efficient while providing accurate results. Additionally, analyses of the losses in the turbine are isolated and documented. Results indicate that large separation regions occur on the turbine blades which drastically affect the torque created by the turbine, the location of flow separation is documented and compared among various flow regimes. The model and simulations show good agreement with the experimental results and the two proposed solutions enhance the performance of the turbine showing an approximate 10% increase in efficiency based on simulation results.

Thesis (MScEng) -- Stellenbosch University, 2014. / ENGLISH ABSTRACT: South Africa has a signi cant potential resource for electrical power generation in the Agulhas Current on the southeast coast. The Ocean Current Energy Convertor studied in this project was designed to generate power from this current. The feasibility of this device was investigated by analysing the dynamic stability and controllability of the convertor, when acted upon by hydrodynamic forces while harvesting energy from the current. A simulation model was developed to predict the dynamic behaviour using the Simulink software suite. A scale model of the prototype was built and tested in the Towing Tank at Stellenbosch University, and the experimental results were compared against the simulation results. A control algorithm was designed, using the mathematical model, to control the roll angle and deployment depth. The control algorithm was tested in simulation. The results indicated that the simulation model accurately predicted the behaviour of the prototype in testing, and results showed that the device is both stable and controllable. It was concluded that this OCEC design concept warrants further investigation. The recommendations are that the experimental model be improved to ensure reliable experimental results, that further complexity be added to the simulation model, and that the control algorithm be tested on the improved prototype in the towing tank. / AFRIKAANSE OPSOMMING: Die Agulhas-seestroom aan die suidooskus van Suid-Afrika bied 'n aansienlike potensiële hulpbron vir elektriese kragopwekking. Die seestroomenergieomsetter (SEO) wat in hierdie projek bestudeer is was ontwikkel om krag uit hierdie seestroom te genereer. Die doenlikheid van hierdie toestel is ondersoek deur die dinamiese stabiliteit en beheerbaarheid van die omsetter onder die invloed van hidrodinamiese kragte te analiseer terwyl dit energie van die stroom inwin. 'n Simulasiemodel is met behulp van Simulink-sagteware ontwikkel om die dinamiese gedrag te voorspel. 'n Skaalmodel van die prototipe was gebou en in die sleeptenk by Universiteit Stellenbosch getoets en die eksperimentele resultate met die simulasie se resultate vergelyk. 'n Beheer-algoritme is daarna ontwerp, deur middel van die wiskundige model, om die rolhoek en diepte van ontplooiing te beheer.Hierdie algoritme is tydens simulasie getoets. Die resultate het aangedui dat die simulasiemodel akkuraat die gedrag van die prototipe tydens toetse voorspel het, en die resultate het gewys dat die toestel beide stabiel en beheerbaar is. Die gevolgtrekking is gemaak dat die SEO se ontwerpkonsep verdere studie regverdig. Die aanbevelings is dat die eksperimentele model verbeter word om betroubare eksperimentele resultate te verseker, dat verdere kompleksiteit by die simulasiemodel gevoeg word, en dat die beheer-algoritme op die verbeterde model in die sleeptenk getoets word.

The energy of the tides represents one globally existent source of renewable energy, and has the potential to play a major role in a sustainable future. An assessment of the potential for tidal energy extraction using marine current turbines at a particular location in the Beaufort River near Parris Island, South Carolina is presented. The Marine Corps Recruit Depot located on Parris Island is situated between the confluence of the Broad and Beaufort Rivers. These rivers are tidally dominated, and experience some of the largest tidal ranges in the southeastern United States, between 2.5 and 3 meters during spring tide periods. Because Parris Island already has much of the necessary land-based infrastructure in place, there is logical potential for the extraction of kinetic energy from the nearby tidal streams using underwater turbines for power production. In order to evaluate the potential of a particular location to produce significant amounts of energy using these types of devices, extensive investigations must be conducted to determine important site characteristics such as water depth, current velocity, and water level fluctuations over time. This potential was investigated using in-situ measurements in the vicinity of the pump station on Parris Island, and by developing a numerical model of the region using the Regional Ocean Modeling System (ROMS). This model was calibrated using the results from the in-situ measurements, and was then used to determine the impacts of tidal energy extraction on the local flow field. Results from in-situ measurements indicate that tidal currents along the portion of the Beaufort River analyzed in this study are driven primarily by the semi-diurnal M2 tidal constituent. The tidal range at the study site is approximately 2 meters on average, with a mean depth-averaged current velocity magnitude of 0.57 m/s predicted for a period of one year. A mean depth-averaged current velocity magnitude of 0.59 m/s was observed over the course of the longer-term ADCP deployment from November 12 to December 17, 2009. The maximum current speed at the site is approximately 1.2 m/s at the water surface. The ROMS model applied to the coastal areas surrounding Parris Island, SC produces results that closely resemble in-situ measurements collected previously during both the boat-based survey and the longer-term ADCP deployment. In the analysis of the effects of energy extraction from the system, four separate cases were considered in which 10, 20, 30, and 60% of the total kinetic energy contained in the flow was dissipated near the location of the longer-term ADCP deployment. Minimal impacts on the local hydrodynamics were observed across the four cases considered.

Ocean currents are an attractive source of clean energy due to their inherent reliability, persistence and sustainability. The Gulf Stream system is of particular interest as a potential energy resource to the United States with significant currents and proximity to the large population on the U.S. east coast. To assess the energy potential from ocean currents for the United States, the characterization of ocean currents along the U.S. coastline is performed in this dissertation. A GIS database that maps the ocean current energy resource distribution for the entire U.S. coastline and also provides joint velocity magnitude and direction probability histograms is developed. Having a geographical constraint by Florida and the Bahamas, the Florida Current has the largest ocean current resource which is fairly stable with prevalent seasonal variability in the upper layer of the water column (~200m). The core of the Florida Current features higher stability than the edges as a result of the meandering and seasonal broadening of the current flow. The variability of the Gulf Stream significantly increases as it flows past the Cape Hatteras. The theoretical energy balance in the Gulf Stream system is examined using the two-dimensional ocean circulation equations based on the assumptions of the Stommel model for quasi-geostrophic subtropical gyres. Additional turbine drag is formulated and incorporated in the model to represent power extraction by turbines. Parameters in the model are calibrated against ocean observational data such that the model can reproduce the volume and kinetic energy fluxes in the Gulf Stream. The results show that considering extraction over a region comprised of the entire Florida Current portion of the Gulf Stream system, the theoretical upper bound of averaged power dissipation is around 5.1 GW, or 45 TWh/yr. If the extraction area comprises the entire portion of the Gulf Stream within 200 miles of the U.S. coastline, the theoretical upper bound of averaged power dissipation becomes approximately 18.6 GW or 163 TWh/yr. The impact of the power extraction is primarily constrained in the vicinity of the turbine region, and includes a significant reduction of flow strength and water level drop in the power extraction site. The turbines also significantly reduce residual energy fluxes in the flow, and cause redirection of the Gulf Stream. A full numerical simulation of the ocean circulation in the Atlantic Ocean is performed using Hybrid Coordinate Ocean Model (HYCOM) and power extraction from the Florida Current is modeled as additional momentum sink. Effects of power extraction are shown to include flow rerouting from the Florida Strait channel to the east side of the Bahamas. Flow redirection is stronger during peak summer flow resulting in less seasonal variability in both power extraction and residual fluxes in the Florida Current. A significant water level drop is shown at the power extraction site, and so is a slight water level rise along the coasts of Florida and the Gulf. The sum of extracted power and the residual energy flux in the Florida Current is lower than the original energy flux in the baseline case, indicating a net loss of energy reserve in the Florida Current channel due to flow redirection. The impact from power extraction on the mean flow field is concentrated in the near field of the power extraction site, while shifts in the far flow field in time and space have little impact on the overall flow statistics.

The huge natural energy resources available in the world’s oceans are attracting increasing commercial and political interest. In order to evaluate the status and the degree of acceptability of future Ocean Energy (OE) schemes, it was considered important to develop an Integrated Assessment Methodology (IAM) for ascertaining the relative merits of the competing OE devices being proposed. Initial studies included the gathering of information on the present status of development of the ocean energy systems on wave, OTEC and tidal schemes with the challenges faced for their commercial application. In order to develop the IAM, studies were undertaken for the development and standardization of the assessment tools focussing on: • Life Cycle Assessment (LCA) on emission characteristics. • Energy Accounting (EA) studies. • Environmental Impact Assessment (EIA) over different environmental issues. • Resource captures aspects. • Defining economy evaluation indices. The IAM developed from such studies comprised of four interrelated well defined tasks and six assessment tools. The tasks included the identification of the modus operandi on data collection to be followed (from industry) for assessing respective OE devices, and also advancing relevant guidelines as to the safety standards to be followed, for their deployment at suitable sites. The IAM as developed and validated from case studies in ascertaining relative merits of competing OE devices included: suitable site selection aspects with scope for resource utilisation capability, safety factors for survivability, scope for addressing global warming & energy accounting, the environmental impact assessment both qualitatively and quantitatively on different environmental issues, and the economic benefits achievable. Some of the new ideas and concepts which were also discovered during the development of the IAM, and considered useful to both industry and researchers are given below: • Relative Product Cost (RPC) ratio concept- introduced in making an economic evaluation. This is considered helpful in sensitivity analysis and making design improvements (hybridising etc) for the cost reduction of OE devices. This index thus helps in making feasibility studies on R&D efforts, where the capital cost requirement data and life span of the device is not well defined in the primary stages of development. • Determination of the threshold limit value of the barrage constant - considered useful in determining the efficacy of the planning process. The concept ascertained the relative efficiency achieved for various barrage proposals globally. It could also be applied to suggest the revisions required for certain barrage proposals and also found useful in predicting the basin area of undefined barrage proposal for achieving economic viability. • Estimations made on the future possibility of revenue earnings from the by-products of various OTEC types, including the scope of chemical hubs from grazing type OTEC plants. • Determination of breakeven point- on cost versus life span of wave and OTEC devices studied, which is useful in designing optimum life of the concerned devices. The above stated multi-criterion assessment methodology, IAM, was extended leading to the development of a single criterion model for ascertaining sustainability percent achievable from an OE device and termed IAMs. The IAMs was developed identifying 7 Sustainability Development Indices (SDI) using some the tools of the IAM. A sustainability scale of 0-100 was also developed, attributing a Sustainability Development Load Score (SDLS) percentage distribution pattern over each SDIs, depending on their relative importance in achieving sustainability. The total sum of sustainability development (SD) gained from each SDI gave the IAMs (for the concerned device), indicating the total sustainable percentage achieved. The above IAMs developed, could be applied in ranking OE devices alongside the unsustainable coal power station. A mathematical model of estimating the IAMs was formulated, in order to ascertain the viability to the sustainable development of any energy device. The instruments of IAM and IAMs which have been developed would be helpful to the OE industry in ascertaining the degree of acceptability of their product. In addition it would also provide guidelines for their safe deployment by assessing the relative merits of competing devices. Furthermore, IAM and IAMs would be helpful to researchers undertaking feasibility studies on R&D efforts for material development research, ‘hybridization studies’ (as also new innovations), cost reduction, the performance improvement of respective devices, and any economic gains. With future advancements in OE systems and the availability of field data from large scale commercial applications, the specific values/data of the IAM & IAMs may be refined, but the logic of the models developed in this research would remain the same.

Thesis (MBA)--Stellenbosch University, 2011. / Gaia Power is a South African start-up in the renewable energy industry. Among other products, they developed a wave energy converter, which is a device used to extract energy from ocean waves. This research deals with the economic feasibility study of the wave energy converter. Wave energy is a young field of research, especially in the South African context. Therefore sources for multiple angles of the project had to be found, analysed and brought into the Gaia Power context. Understanding the cost drivers of a wave energy plant was the foundation of the research itself. The Gaia Power specific levelised cost of electricity generation was calculated based on actual supplier quotes, reference costs found in the literature as well as assumptions. Still, such a calculation is actually more an estimation due to a high uncertainty level in all cost components. Especially the construction cost as well as the discount rate used have therefore been tested for sensitivity. Gaia Power‟s target production cost was R0.54 kWh, which equalled the Eskom tariff at the time of this research. Taking into account a R0.10/kWh fee payable to Eskom, the target cost sank to R0.44, which is about 25 percent lower than the minimum value for electricity generation cost found in the literature. This target was therefore expected to be and proved to be difficult to reach. The calculated levelised electricity cost was R0.99/kWh, with a possible range of R0.54/kWh to R1.60/kWh observed in the sensitivity analysis. These results show that the Gaia Power wave energy converter in the given specifications was not economically feasible. It was therefore recommended to rethink the specifications in order to reduce construction cost, which proved to be the largest cost driver. Besides the quantitative findings, this research also has a strong qualitative side. During the whole research it became obvious that there was an overall high risk level in the project due to the lack of experience with wave energy in general and in South Africa specifically, as well as the high impact of weather on the construction. Those risks were identified, analysed and recommended mitigation actions were derived.

This thesis aims to facilitate the siting and implementation of Florida Atlantic University Southeast National Marine Renewable Energy Center (FAU SNMREC) ocean current energy (OCE) projects offshore southeastern Florida through the analysis of benthic anchoring conditions. Specifically, a suitability analysis considering all presently available biologic and geologic datasets within the legal framework of OCE policy and regulation was done. OCE related literature sources were consulted to assign suitability levels to each dataset, ArcGIS interpolations generated seafloor substrate maps, and existing submarine cable pathways were considered for OCE power cables. The finalized suitability map highlights the eastern study area as most suitable for OCE siting due to its abundance of sand/sediment substrate, existing underwater cable route access, and minimal biologic presence. Higher resolution datasets are necessary to locate specific OCE development locales, better understand their benthic conditions, and minimize potentially negative OCE environmental impacts. / Includes bibliography. / Thesis (M.S.)--Florida Atlantic University, 2014. / FAU Electronic Theses and Dissertations Collection