Abstract The purpose of this thesis is to design and fabricate optical waveguide reflectors by using vertical mirror reflector. In order to reflect the incident optical mode of multi-mode interference coupler, we fabricate the etched vertical reflective mirror surface with dry etch processes. We used the design of etched vertical mirror surfaces to bend the incident optical mode, and changed the length of multi-mode interference coupler for the power splitting ratio and high power output. In order to make total internal reflection in vertical reflective mirror, we used ICP-RIE dry etching process to fabricate vertical and smooth mirror. In this part of design the semiconductor optical filter, we design the 90o vertical mirror reflector and the length of MMI by using a 2¡Ñ2 multi-mode interference coupler to get the power splitter with coupling coefficient. We comprise the ring resonator by two vertical mirror reflector and bended waveguide to displace the cleaved of Fabry-Perot resonator in tradition. In fabrication process, we using dry etching (ICP-RIE) process that is the plasma system high density in all part of this paper. first, we defined the device pattern by using photo-lithography technique in our sample . Second, we etched ridge waveguide by using dry etching ICP-RIE method. In order to decrease the scattering loss, we deep etched bended waveguide and the reflector. Then, we etched the reflector mirror by ICP-RIE dry etching process to get smoother surface. Finally, we used polyimide to flatten the sides of the ridge waveguide and evaporated metal electrode. In the device characteristic, we get the waveguide loss in 35.68dB by Fabry-Perot resonator and a power splitter with 85 percent and 15 percent output. Finally, we could get a transmission frequency about 81GHz from optical transmission spectrum in the filter device.

Analysis and experimental results on a polarization independent electrooptic matched filter (EMF) with a center wavelength of 1.53 μm are reported. The EMF utilizes electrooptic phase-matched TE↔TM conversion in a Ti-diffused waveguide on a LiNbO3 substrate. The operation of the EMF to select an optical frequency channel is controlled by applying independent voltages to interdigital electrode sets cascaded along a single mode waveguide. The device is inherently polarization independent and has the potential for submicrosecond tuning. The number of selectable channels N is related to the number of electrode sets P by the formula / 2 1 N P = + . A matrix analysis is used to determine the TE↔TM conversion efficiency for the case that 8 P = and 5 N = . A driving circuit for the EMF was implemented using a digital-to-analog converter (DAC) array controlled from a personal computer (PC). Transmittance spectra of a filter produced in a LiNbO3 substrate are presented. A raised cosine weighting function applied along the 3.8 cm length of an EMF provides a sidelobe suppression level better than –17 dB with a 1.0 nm 3-dB bandwidth.

No description available.

A tunable guided-wave optical filter that performs spectral slicing at the 1530nm wavelength regime in Ti:LiNbO3 was proposed and fabricated. It is aimed at minimizing crosstalk between channels in dense wavelength division multiplexing (DWDM) optical network applications. The design utilizes a sparse grating allowing the selection of equally spaced channels in the frequency domain. Between selected channels, equally spaced nulls are also produced. The sparse grating is formed by using N coupling regions with different lengths along the direction of propagation of light in the waveguide, generating N-1 equally spaced nulls between adjacent selected channels. The distance between the centers of adjacent coupling regions is kept constant. The filtering is based on codirectional polarization coupling between transverse electric (TE) and transverse magnetic (TM) orthogonal modes in a waveguide through an overlay of strain-induced index grating, via the strain-optic effect. Two types of devices were fabricated. In the first type, the sparse gratings were produced on straight channel waveguides. Selected channels emerge from the device in a polarization state orthogonal to the input and a polarizer is needed to observe the filtered light. For the second type, an asymmetric Mach-Zehnder interferometer configuration was used to eliminate the need of the polarizer at the output, and yields an output response that is polarization independent. Both types of devices were fabricated on x-cut y-propagating LiNbO3 substrates, with N = 6 strain-induced coupling regions. The single mode channel waveguides were formed by Ti diffusion. Electrode patterns centered about the optical waveguide were defined by liftoff. In the straight channel devices, insertion loss was less than 2.5 dB on a 43 mm sample. The 3-dB channel bandwidth of the selected channels is approximately 1.0 nm. Devices were tuned thermally as well as by voltage application to surface electrodes resulting in tuning rates of 1.0 nm/oC and 0.04148 nm/V, respectively. In the polarization independent device the insertion loss for the phase-matched wavelength was 5.3 dB on a 53 mm long chip. The 3-dB bandwidth was also ~1.0 nm and the thermal tuning rate 1.0 nm/oC. The experimental results are in good agreement with design theory.

Broad spectral tunability is a desired feature of many photonic and plasmonic components, such as optical filters, semiconductor lasers, and plasmonic materials. Here I show that unique properties of long-range surface plasmon polaritons (LR SPP) allow one to produce optical components with very wide tuning range using small variations in the refractive index of the dielectric cladding material. As a proof-of-concept demonstration, I present operation of LR-SPP-based bandpass optical filters in which a 0.004 variation in the refractive index of the cladding dielectric translates into 210 nm of bandpass tuning at telecom wavelengths. The tuning mechanism proposed here may be used to create monolithic bandpass filters with tuning range spanning over more than an optical octave, compact and widely-tunable diode and quantum cascade laser systems, multi-spectral imagers, and other plasmonic components with broadly-tunable optical response. / text

All-fiber multireflector spectral filters which have potential application in optical communications have been investigated experimentally. These multireflector etalons were produced by aligning equal-length fiber sections with TiO2/SiO2 dielectric mirrors deposited on the end in a silicon v-groove. Fiber sections 1.33mm in length were produced by polishing, with the fibers held in a silicon wafer polishing jig. The fibers were aligned inside the polishing jig using a precision micro positioner. Then four polishing steps with increasingly finer grit were applied to produce high-quality polished end surfaces on each fiber section. Finally, a dielectric mirror was deposited on one end of each fiber section by magnetron sputtering. After characterizing the optical loss, length, and mirror reflectance for each of the fiber sections, sections which were well-matched in length were chosen for assembly of the four-mirror etalon, which had nominal reflectance values of 10%, 50%, 50%, and 10% for the dielectric mirrors. Measured transmittance spectra for a mutireflector spectral filter were compared with calculated spectra. Thermal tuning of the multireflector etalon was also investigated. A 0.34 nm wavelength shift was observed for a 23° C temperature change, in agreement with prediction. increasingly finer grit were applied to produce high-quality polished end surfaces on each fiber section. Finally, a dielectric mirror was deposited on one end of each fiber section by magnetron sputtering. After characterizing the optical loss, length, and mirror reflectance for each of the fiber sections, sections which were well-matched in length were chosen for assembly of the four-mirror etalon, which had nominal reflectance values of 10%, 50%, 50%, and 10% for the dielectric mirrors. Measured transmittance spectra for a mutireflector spectral filter were compared with calculated spectra. Thermal tuning of the multireflector etalon was also investigated. A 0.34 nm wavelength shift was observed for a 23° C temperature change, in agreement with prediction.

No description available.

Interferometric fiber optic sensors have been extensively used to measure a large variety of physical, chemical and biomedical parameters due to their superior performance. At the Center for Photonics Technology of Virginia Tech, a variety of interferometric fiber optic sensors have been developed in recent years, for efficient oil recovery, partial discharge detection in high voltage transformers, pressure sensing in gas turbine engines, and temperature measurements in gasifiers and boilers. However, interrogating an interferometric sensor involves accurate recovery of a measurand from the phase-modulated lightwaves, and has been a challenge for high performance, high speed, and low-cost, to current white-light interferometry (WLI) techniques, such as the widely used scanning WLI (S-WLI) and spectral-domain WLI (SD-WLI). The performance of a white-light interferometric sensing system depends not only on the design of the probes, but also, to a great extent, on the interrogation strategy to be used. In this Ph.D. research, a tunable optical filter based WLI (TOF-WLI) is proposed and validated as a low cost, yet high performance, solution to the interrogation of various types of interferometric sensors. In addition to the capability of linear/quadrature demodulation, TOF-WLI retains all the features of WLI, is compatible with the SD-WLI, and can be tailored for both static and wideband signals. It also has great potential in surface metrology and biomedical imaging as well as optical spectroscopy. The key, to the success of this new approach in competition with the other available WLI techniques, is that the tunable optical filter (TOF) must be specially designed for sensing and extremely low cost. Therefore, two novel TOFs, a diffraction grating tunable filter (DG-TOF) and an extrinsic Fabry-Perot tunable filter (EFP-TF), are proposed and demonstrated. Laboratory and field test results on using the DG-TOF WLI for partial discharge and thermal fault detection in high voltage power transformers, and the EFP-TF WLI in temperature sensor systems and a turbine engine monitoring system will also be presented to demonstrate the feasibility for efficient sensor interrogation. / Ph. D.

This thesis presents a detailed study of complementary metal-oxide-semiconductor (CMOS) compatible silicon waveguide and ring resonator technologies. The project specifically focuses on a range of slotted ring resonator configurations comprised of rib-style waveguides. Single ring resonators and Mach-Zehnder interferometers with double rings and central drop port channels have been successfully characterised. Thermal tuning techniques using on-chip heaters were used to determine their sensitivities. A stringent signal cleaning method was also developed to remove systematic background noise. Analysing the transmission signals produced by the Mach-Zehnder interferometers with double rings and a central drop port, it was revealed that coupled resonator induced transparency (CRIT) is created along with Fano-type resonances when the resonant peaks of the two ring resonators are tuned to overlap. The tuning of these features revealed a 2.7 and 2-fold improvement in device sensitivity. A 3x3 transfer matrix model has been developed to simulate the behaviour of light travelling through this configuration. Modelling suggests that effective refractive index and relative phase are the key factors in determining this behaviour. When tuned to close proximity, a resonant ‘superstate’ is achieved in which a modified model is required. Applying the single ring resonators to biosensing applications, basic refractive index testing and a glucose sensing calibration were conducted. A polydimethylsiloxane (PDMS) based microfluidics system was also developed to improve the reliability of sensing and enable automation. Using silicon nitride ring resonators with inkjet-printed upconverting nanoparticles, it was found that the evanescent field of the rings could stimulate the upconversion process revealing visible spectrum emission around the rings.

Thesis advisor: Michael J. Naughton / Nanoscale biosensing devices improve and enable detection mechanisms by taking advantage of properties inherent to nanoscale structures. This thesis primarily describes the development, characterization and application of two such nanoscale structures. Namely, these two biosensing devices discussed herein are (1) an extended-core coaxial nanogap electrode array, the ‘ECC’ and (2) a plasmonic resonance optical filter array, the ‘plasmonic halo’. For the former project, I discuss the materials and processing considerations that were involved in the making of the ECC device, including the nanoscale fabrication, experimental apparatuses, and the chemical and biological materials involved. I summarize the ECC sensitivity that was superior to those of conventional detection methods and proof-of-concept bio-functionalization of the sensing device. For the latter project, I discuss the path of designing a biosensing device based on the plasmonic properties observed in the plasmonic halo, including the plasmonic structures, materials, fabrication, experimental equipment, and the biological materials and protocols. / Thesis (PhD) — Boston College, 2019. / Submitted to: Boston College. Graduate School of Arts and Sciences. / Discipline: Physics.