Monolithic passively mode-locked colliding pulse semiconductor lasers generating pico- to sub-picosecond terahertz optical pulse trains are promising sources for future applications in ultra-high speed data transmission systems and optical measurements. However, in the absence of external synchronization, these passively mode-locked lasers suffer from large amplitude and timing jitter instabilities resulting in broad comb linewidths, which precludes many applications in the field of coherent communications and signal processing where a much narrower frequency line set is needed. In this dissertation, a novel quantum dot based coupled cavity laser is presented, where for the first time, four-wave mixing (FWM) in the monolithically integrated saturable absorber is used to injection lock a monolithic colliding pulse mode-locked (CPM) laser with a mode-locked high-Q ring laser. Starting with a passively mode-locked master ring laser, a stable 30 GHz optical pulse train is generated with more than 10 dB reduction in the RF noise level at 20 MHz offset and close to 3-times reduction in the average optical linewidth of the injection locked CPM slave laser. The FWM process is subsequently verified experimentally and conclusively shown to be the primary mechanism responsible for the observed injection locking. Other linear scattering effects are found to be negligible, as predicted in the orthogonal waveguide configuration. The novel injection locking technique is further exploited by employing optical hybrid mode-locking and increasing the Q of the master ring cavity, to realize an improved stabilization architecture. Dramatic reduction is shown with more than 14-times reduction in the photodetected beat linewidth and almost 5-times reduction in the optical linewidth of the injection locked slave laser with generation of close to transform limited pulses at ~ 30 GHz. These results demonstrate the effectiveness of the novel injection locking technique for an all-on-chip stability transfer and provides a new way of stabilizing monolithic optical pulse sources for applications in future high speed optical networks.

Les oscillateurs sont présents dans tous les systèmes de communications que nous utilisons. Ils nous permettent de faire la synchronisation entre l’émetteur et le récepteur d’un message. La qualité de cette synchronisation dépend de la stabilité de l’oscillateur. Afin de caractériser cette stabilité dans le domaine fréquentiel, le bruit de phase est utilisé comme paramètre de référence. Un oscillateur qui délivre un signal avec une faible valeur de bruit de phase est un oscillateur de grande pureté spectrale. Les oscillateurs électroniques ont une bonne performance à basse fréquence. En mesure de la demande des systèmes de très haut débit, les oscillateurs électroniques ne sont pas capables de produire signaux qu’avec l’utilisation de multiplicateurs de fréquence qui ajoutent plusieurs éléments à la chaine de communication. Les systèmes hybrides permettent de prendre d’avantage la bonne performance de composants optiques en haute fréquence afin de les intégrer dans les systèmes électroniques et surmonter de cette façon-là les limitations fréquentielles des systèmes électroniques. Ce travail vise l’utilisation de la technique de verrouillage optique par injection du faisceau d’un laser maître vers la cavité d’un VCSEL sous modulation directe dans la boucle d’oscillation. La technique du verrouillage optique du VCSEL permets d’élargir la bande passante de modulation directe du VCSEL et réduire son bruit d’intensité (Relative Intensity Noise - RIN). La réduction du RIN a comme effet secondaire la réduction de la contribution du bruit additif dans l’oscillateur et, en conséquence, la réduction du bruit de phase de l’oscillateur. / Oscillators are present in all telecommunication systems. They synchronize the emitter and receiver of a message. The quality of the synchronization depends on the oscillator stability. To characterize the frequency domain oscillator stability, the phase noise of the carrier is used as figure of merit. An oscillator delivering a low phase noise carrier is a high spectral purity oscillator. Electronic oscillators are high performing at low frequencies. As communications systems require high data rate transmission, the electronic oscillators uses frequency multipliers that degrades the spectral purity of the carrier. The hybrid systems take advantage of the good performance of optical components at high frequency with the goal to be integrated in the electronic systems to overcome frequency limitation issues. This work use the optical injection locking technique by injecting the laser beam of a master laser inside the cavity of a VCSEL under direct modulation. The optical injection locking technique enlarges the direct modulation bandwidth of the VCSEL and reduces the Relative Intensity noise of the laser (RIN). The RIN reduction has as side effect the reduction of the additive noise inside the oscillator and, in consequence, reducing the oscillator phase noise.

Submitted by Maike Costa (maiksebas@gmail.com) on 2016-03-16T11:48:24Z No. of bitstreams: 1 arquivototal.pdf: 3030423 bytes, checksum: 121b1c06c249f60685f65714d1f26c0e (MD5) / Made available in DSpace on 2016-03-16T11:48:24Z (GMT). No. of bitstreams: 1 arquivototal.pdf: 3030423 bytes, checksum: 121b1c06c249f60685f65714d1f26c0e (MD5) Previous issue date: 2014-08-28 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES / Here we present a systematic analysis of the dynamics in the frequency of semiconductor lasers in systems under orthogonal optical feedback or external injection, with and without frequency discriminator. We measure the parameter of proportionality between the change of frequency and the power level of the orthogonally polarized light injected into the cavity. We perform an application of this injection technique for frequency sweep that allows varying the frequency in a range of tens of GHz and apply it in an experience of spectroscopy. This technique allows frequency sweep without changing the main laser power, which is fed by another, control laser, whose wavelength is di erent from the principal. We have analyzed the dynamics of the semiconductor laser frequency subject to orthogonal optical feedback and injection in a con guration where a di raction grating works as a spectral lter. Using a di raction grating as frequency discriminator in these systems, we observe a dynamical behavior in the laser emission frequency. / Apresentamos neste trabalho uma an alise sistem atica em rela c~ao a din^amica em frequ^encia de lasers semicondutores em sistemas sob realimenta c~ao e inje c~ao otica ortogonal com e sem discriminador de frequ^encia. Medimos o par^ametro de proporcionalidade entre o deslocamento em frequ^encia e a varia c~ao da pot^encia injetada ortogonalmente na cavidade. Montamos alguns sistemas com a nalidade de varrer a frequ^encia de emiss~ao de um laser semicondutor, explorando con gura c~oes sob inje c~ao otica ortogonal. Entre elas, zemos uma aplica c~ao de uma t ecnica que permite obter uma varia c~ao de dezenas GHz em uma experi^encia de espectroscopia, sem variar a pot^encia de sa da do laser principal o qual e alimentado por outro laser de controle com comprimento de onda diferente do principal. Analisamos a dinamica em frequencia do laser semicondutor sujeito a realimenta cao e inje cao otica ortogonal com uma grade de difra cao empregada como ltro espectral. Usando uma grade de difra cao como discriminador de frequencia nesses sistemas, observamos um comportamento semelhante a uma oscila cao na frequencia.

A disponibilização de fontes ópticas multi-comprimento de onda de baixo custo certamente é um dos aspectos fundamentais para viabilizar a implantação de redes WDMPON (Wavelength Division Multiplexing-Passive Optical Network). Na literatura, são encontradas propostas de algumas tecnologias para a construção de tais dispositivos como a utilização de fontes ópticas sintonizáveis, uso de um vetor de lasers DFB (Distributed Feedback Laser) ou, até mesmo, o fatiamento espectral de uma fonte de banda larga. Contudo, essas propostas apresentam custo elevado, ou limitações de operação, tornando-se inapropriadas para a aplicação de interesse. Uma alternativa que vem sendo amplamente utilizada é o travamento óptico de diodos laser de Fabry-Pérot (FP-LD - Fabry-Pérot laser diode), realizado por meio da injeção de sinal óptico externo provindo do fatiamento espectral de uma fonte de banda larga. O travamento óptico possibilita o controle espectral do FP-LD, e o seu baixo custo torna essa fonte óptica atrativa na implantação de redes WDM. O entendimento do mecanismo de travamento torna-se, então, crucial na descrição da dinâmica de tais fontes ópticas. Desta forma, nesta dissertação, foi desenvolvido o estudo dos modelos matemáticos que descrevem a dinâmica de lasers travados, assim como foi investigado o desempenho de redes WDM-PON empregando estas fontes ópticas. / The availability of low cost multi-wavelength optical sources is certainly one of the fundamental aspects to allow the deployment of WDM-PON networks. Several technologies for the implementation of such optical sources are discussed in the literature, including tunable lasers, DFB arrays and spectral slicing of a broadband light source. However, those propositions suffer from high cost or operational limitations. One alternative is the optical injection locking of a Fabry Pérot laser diode (FPLD), in which the external optical injection signal is obtained from the spectral slicing of a broadband light source. This option has been widely investigated because the optical injection locking process allows for the FP-LD optical spectral control and wavelength selection. In addition, the low cost of such device makes this optical source an attractive solution for WDM-PON widespread deployment. In this context, the understanding of the locking mechanism becomes important in the optimization of such optical sources. Thus, in this dissertation, we conducted a study of mathematical models that describe the dynamics of locked lasers as well as investigated the performance of WDM-PON based on those optical sources.

Cette thèse porte sur l'étude de structures lasers à semi-conducteurs à base d'îlots et de bâtonnets quantiques, connues pour avoir quelques propriétés remarquables telles leur fort gain, leur effet non-linéaire renforcé, leur faible courant de seuil, leur haute température caractéristique ... Les caractérisations en termes de bruit d'intensité et d'injection optique de ces structures montrent un comportement atypique comparativement aux structures classiques (massives ou à base de puits quantiques). Nous avons pu ainsi comparer le bruit d'un laser DFB à bâtonnets quantiques avec celui d'un laser DFB massif ou à puits quantiques. Des études comparatives de bruit ont aussi été effectuées sur des lasers de type Fabry-Perot. Une modélisation du bruit a été confrontée aux résultats expérimentaux et montre l'importance de la prise en compte de la couche de mouillage. L'injection optique, contrairement aux propriétés d'un laser classique, présente un grand nombre de régimes dynamiques fortement non linéaires près du seuil laser (r~1,1) et peu de régimes à seuil modéré (r~3). Ces résultats nous indiquent finalement que le couplage des modes longitudinaux est à la fois fort et fortement amorti par l'interaction avec la couche de mouillage, ce qui nous donne des pistes très intéressantes pour la modélisation du blocage de modes observé dans ces structures. / This thesis focuses on laser diodes made of Quantum Dot/Quantum Dash (QD) structures. These devices have attracted considerable attention due to their remarkable properties, such as high gain, high non-linear effects, low laser-threshold, high thermal stability, etc. Our studies based on RIN (Relative Intensity Noise) and optical injection show unusual behaviour of QD lasers. We have compared the RIN of a QDash DFB laser with a ''classical'' (massif or quantum well) DFB laser as well as for Fabry-Perot type QDot/QDash lasers. Analytical simulations have been faced to experimental results and show the role of the wetting layer. Contrary to what is observed with ''classical lasers'', optical injection exhibits many regimes with strong non-linear dynamics when the laser is biased near the threshold, while there is only a very few regimes at moderate pump. All these results demonstrate a strong coupling with strong dumping between the longitudinal modes through the wetting layer, which is a very interesting point for the understanding of mode-locking in these QDot/QDash structures.

Ce travail de thèse porte sur les systèmes de communication radio-sur-fibre (RoF) aux fréquences millimétriques dans la gamme de fréquences 57-66 GHz et leur génération par voie optique. La technique utilisée repose sur l’emploi de diodes laser à verrouillage de modes à boites quantiques. Au cours de cette thèse, plusieurs études ont été effectuées : la première porte sur la capacité d’intégrer ces types des lasers dans des systèmes de communication RoF avec leurs performances sous modulation directe ou externe. La deuxième étude a été consacrée aux effets de la propagation de ces signaux dans des systèmes basés sur les lasers à blocage de modes. Une technique originale a été mise en place afin de réduire la sensibilité à la dispersion chromatique dans la fibre optique. Une étude de la réduction du bruit de phase des lasers à verrouillage de modes basée sur l’observation de l’effet de la contre réaction et l’injection optique externe a été également présentée. / This thesis focuses on the radio-over-fiber (RoF) communication systems at millimeter frequencies in the frequency range 57-66 GHz and optical generation of a signal at millimeter-wave frequency band. The technique used is based on mode-locked laser diodes. The diodes employed in this work are in quantum dots (or quantum dashes) technology. In this thesis, several studies were conducted: the first relates the ability of integration these types of lasers in the RoF communication systems under direct or external modulation. The second study was devoted to propagation effects. An original technique was implemented to reduce the sensitivity to chromatic dispersion in an optical fiber. A study of the reduction of phase noise mode-locked lasers based on the observation of the reaction effect and against the external optical injection was presented.

A disponibilização de fontes ópticas multi-comprimento de onda de baixo custo certamente é um dos aspectos fundamentais para viabilizar a implantação de redes WDMPON (Wavelength Division Multiplexing-Passive Optical Network). Na literatura, são encontradas propostas de algumas tecnologias para a construção de tais dispositivos como a utilização de fontes ópticas sintonizáveis, uso de um vetor de lasers DFB (Distributed Feedback Laser) ou, até mesmo, o fatiamento espectral de uma fonte de banda larga. Contudo, essas propostas apresentam custo elevado, ou limitações de operação, tornando-se inapropriadas para a aplicação de interesse. Uma alternativa que vem sendo amplamente utilizada é o travamento óptico de diodos laser de Fabry-Pérot (FP-LD - Fabry-Pérot laser diode), realizado por meio da injeção de sinal óptico externo provindo do fatiamento espectral de uma fonte de banda larga. O travamento óptico possibilita o controle espectral do FP-LD, e o seu baixo custo torna essa fonte óptica atrativa na implantação de redes WDM. O entendimento do mecanismo de travamento torna-se, então, crucial na descrição da dinâmica de tais fontes ópticas. Desta forma, nesta dissertação, foi desenvolvido o estudo dos modelos matemáticos que descrevem a dinâmica de lasers travados, assim como foi investigado o desempenho de redes WDM-PON empregando estas fontes ópticas. / The availability of low cost multi-wavelength optical sources is certainly one of the fundamental aspects to allow the deployment of WDM-PON networks. Several technologies for the implementation of such optical sources are discussed in the literature, including tunable lasers, DFB arrays and spectral slicing of a broadband light source. However, those propositions suffer from high cost or operational limitations. One alternative is the optical injection locking of a Fabry Pérot laser diode (FPLD), in which the external optical injection signal is obtained from the spectral slicing of a broadband light source. This option has been widely investigated because the optical injection locking process allows for the FP-LD optical spectral control and wavelength selection. In addition, the low cost of such device makes this optical source an attractive solution for WDM-PON widespread deployment. In this context, the understanding of the locking mechanism becomes important in the optimization of such optical sources. Thus, in this dissertation, we conducted a study of mathematical models that describe the dynamics of locked lasers as well as investigated the performance of WDM-PON based on those optical sources.

Une impulsion laser intense se propageant dans un plasma sous-dense (ne<<nc) déplace les électrons sur son passage et crée une onde de sillage à même d'accélérer des électrons. Lorsque l'impulsion est très intense (I₀> 10¹⁸ W.cm⁻²) et de durée très courte (τ₀< 100 fs), , on atteint le régime de la bulle. Les champs électriques dans ces bulles, de l’ordre de 100 GV/m, peuvent accélérer un faisceau d’électrons jusqu’au GeV sur des distances de l’ordre du centimètre. Dans ce régime, les électrons expulsés par la force pondéromotrice du laser forment une fine et dense couche à la surface d'une cavité d'ions restés immobiles. Les propriétés de ce régime sont examinées par l’intermédiaire d’un modèle analytique, que nous avons développé en nous inspirant du travail de W. Lu et S. Yi. En nous plaçant dans ce régime prometteur, nous avons étudié les mécanismes d’injection et de piégeage dans l'onde de sillage. Dans l’injection optique, les polarisations parallèles ou circulaires positives conduisent respectivement à une injection mettant en jeu du chauffage stochastique, ou à l’injection froide. Un paramètre de similarité est introduit, celui-ci permet de déterminer la méthode d’injection la plus appropriée pour maximiser la charge injectée. Enfin, le modèle analytique présenté en première partie est étendu afin d’étudier l’onde de sillage dans le régime de la bulle lorsqu’un champ magnétique longitudinal initial est appliqué au plasma. Lorsque le plasma est magnétisé deux phénomènes remarquables se manifestent, d'une part une ouverture apparaît à l'arrière de la bulle et d'autre part un mécanisme d'amplification du champ magnétique longitudinale est induit par la variation du flux magnétique. Les prédictions de notre modèle analytique sont confrontées aux résultats de simulations PIC 3D issues du code CALDER-Circ. La conséquence immédiate de la déformation de l'onde de sillage est la réduction, voire la suppression de l'auto-injection. L’application d’un champ magnétique longitudinal, combinée à un choix judicieux des paramètres laser-plasma, permet de réduire la dispersion en énergie des faisceaux d’électrons produits après injection optique. / An intense laser pulse propagating in an under dense plasma (ne<<nc) expels electrons and a wakefield is created which can accelerate efficiently electrons. When the laser pulse is very intense (I₀> 10¹⁸ W.cm⁻²) and short(τ₀< 100 fs), the bubble regime is reached. Within the bubble the electric field can exceed 100 GV/m and a trapped electron beam is accelerated to GeV energy with few centimetres of plasma.In this regime, the electrons expelled by the laser ponderomotive force are brought back and form a dense sheath layer. First, an analytic model was derived using W. Lu and S. Yi formalisms in order to investigate the properties of the wakefield in the blowout regime. In a second part, the trapping and injection mechanisms into the wakefield were studied. When the optical injection scheme is used, electrons may undergo stochastic heating or cold injection depending on the lasers’ polarisations. A similarity parameter was introduced to find out the most appropriate method to maximise the trapped charge. In a third part, our analytic model is extended to investigate the influence of an initially applied longitudinal magnetic field on the laser wakefield in the bubble regime. When the plasma is magnetized two remarkable phenomena occur. Firstly the bubble is opened at its rear, and secondly the longitudinal magnetic field is amplified - at the rear of the bubble - due to the azimuthal current induced by the variation of the magnetic flux. The predictions of our analytic model were shown to be in agreement with 3D PIC simulation results obtained with Calder-Circ. In most situations the wake shape is altered and self-injection can be reduced or even cancelled by the applied magnetic field. However, the application of a longitudinal magnetic field, combined with a careful choice of laser-plasma parameters, reduces the energy spread of the electron beam produced after optical injection.

Kvantové kaskádové laserové frekvenční hřebeny jsou slibnými kandidáty pro nové miniaturizované spektrometry bez pohyblivých částí. Mohou být generovány v samočinném režimu pomocí různých nelinearit vyvolaných asymetrickým ziskem a vlnovodovou disperzí. K simulaci samočinných hřebenů byl použit dostupný vysoce optimalizovaný nástroj založený na modelu postupné vlny. Dále byl rozšířen o funkci zamykání optickým vstřikováním, koherentní techniky ovládání frekvenčních hřebenů. Následné simulace potvrdily uzamčení pomocí vstřikovaného signálu. Bylo zjištěno, že disperze grupové rychlosti (GVD) má významný dopad na rozsah zamykání. GVD byla vypočtena pro typické zařízení a frekvenční hřeben byl uzamčen pomocí optického vstřikování v rozsahu ladění od -2 do 47 MHz.

Integration and miniaturisation in electronics has undoubtedly revolutionised the modern world. In biotechnology, emerging lab-on-a-chip (LOC) methodologies promise all-integrated laboratory processes, to perform complete biochemical or medical synthesis and analysis encapsulated on small microchips. The integration of electrical, optical and physical sensors, and control devices, with fluid handling, is creating a new class of functional chip-based systems. Scaled down onto a chip, reagent and sample consumption is reduced, point-of-care or in-the-field usage is enabled through portability, costs are reduced, automation increases the ease of use, and favourable scaling laws can be exploited, such as improved fluid control. The capacity to manipulate single cells on-chip has applications across the life sciences, in biotechnology, pharmacology, medical diagnostics and drug discovery. This thesis explores multiple applications of optical manipulation within microfluidic chips. Used in combination with microfluidic systems, optics adds powerful functionalities to emerging LOC technologies. These include particle management such as immobilising, sorting, concentrating, and transportation of cell-sized objects, along with sensing, spectroscopic interrogation, and cell treatment. The work in this thesis brings several key applications of optical techniques for manipulating and porating cell-sized microscopic particles to within microfluidic chips. The fields of optical trapping, optical tweezers and optical sorting are reviewed in the context of lab-on-a-chip application, and the physics of the laminar fluid flow exhibited at this size scale is detailed. Microfluidic chip fabrication methods are presented, including a robust method for the introduction of optical fibres for laser beam delivery, which is demonstrated in a dual-beam optical trap chip and in optical chromatography using photonic crystal fibre. The use of a total internal reflection microscope objective lens is utilised in a novel demonstration of propelling particles within fluid flow. The size and refractive index dependency is modelled and experimentally characterised, before presenting continuous passive optical sorting of microparticles based on these intrinsic optical properties, in a microfluidic chip. Finally, a microfluidic system is utilised in the delivery of mammalian cells to a focused femtosecond laser beam for continuous, high throughput photoporation. The optical injection efficiency of inserting a fluorescent dye is determined and the cell viability is evaluated. This could form the basis for ultra-high throughput, efficient transfection of cells, with the advantages of single cell treatment and unrivalled viability using this optical technique.