大亚湾反应堆中微子振荡实验通过在不同基线位置测量核电反应堆产生的反中微子的比率及其能量谱，达到精确测量中微子混合角θ₁₃，使sin²2θ₁₃ 的精度在90%置信水平不低于0.01。 / 大亚湾实验一共有8 个反中微子探测器，放置在3 个实验大厅中。反中微子探测器的基本设计是3 层同心圆柱结构：最外层是高5 米直径5 米的不锈钢钢罐，中间有两个有机玻璃罐，直径分别为4 米、3 米，高度分别为4 米、3 米。最内的有机玻璃罐装有掺钆的液体闪烁体，作为探测中微子的靶物质。中间层处于4 米有机玻璃罐与3 米罐之间，装有普通液体闪烁体，用于收集掺钆液体闪烁体中产生的γ 光子能量沉积。最外层是透明的白油，主要用来屏蔽来自钢罐与192 只光电倍增管的天然放射。这些光电倍增管都是安装在钢罐上，浸没于白油中，由液体闪烁体放出的光子全都要经过白油才能被光电倍增管接收，所以，我们需要监测白油光学性质的变化，确保实验结果能够达到精度目标。 / 我们设计并完成一套自动监测光在白油中的衰减的系统。此系统利用一颗高功率发光二极管发出光脉冲，经过50 米的光纤进入反中微子探测器中。通过单光仪内置的步进马达，可以选择特定波长的光进行监测。在反中微子探测器的底部装有一个隅角棱镜，它能把光纤射出的光反射回探测器的顶部，使得光在白油中的传播长度倍增至8 米左右。反射回来的光被白油监测系统的2 英寸光电倍增管接收，信号再通过一个高速模数转换器处理。比较反射信号与参考信号的大小，就可以监测白油对光强的衰减随时间的变化。 / 在本篇论文中，我会详细介绍白油监测系统的设计过程与安装完成后实际运行，取数以及分析的情况。 / The Daya Bay reactor neutrino experiment aims at measuring the neutrino mixing angle θ₁₃ with a sensitivity of 0.01 or better in sin²2θ₁₃ at the 90% confidence level, through a measurement of the relative rates and energy spectra of reactor anti-neutrinos at different baselines. / There are eight anti-neutrino detectors (AD) deployed in three experimental sites. The AD has a three-zone cylindrical structure. Two acrylic vessels with diameter of 3 m and 4 m, and height of 3 m and 4 m respectively, are nested inside a 5m-diameter stainless steel vessel (SSV). The inner most volume, confined by the 3m-diameter inner acrylic vessel (IAV), is filled with Gadolinium doped liquid scintillator (GdLS), which acts as the neutrino target. The medium volume between the IAV and the 4m-outer acrylic vessel (OAV), is filled with normal liquid scintillator (LS) to capture gamma particles emitted from the target. The outer most volume is filled with transparent mineral oil (MO) which shields radiations from the steel or the 192 photo- multipliers (PMT) from entering the target. Since all the PMTs are mounted near the stainless steel wall of the SSV in the MO, the photons emitted by the liquid scintillator have to travel through MO before being detected by the PMT. It is crucial to monitor the optical properties of the MO for achieving the sensitivity of 0.01 in sin²2 θ₁₃. / We have designed and developed an automatic system for monitoring the light attenuation in the MO. The system utilizes a high power LED to send light pulses into the AD through a 50 m optical fiber. With the stepping motor driven monochromator, we can select several wavelengths in one monitoring run. There is a corner cube retro-reflector at the bottom of the AD, which reflects the light back to the top of the AD, thus doubling the light path in the mineral oil to around 8 m. The reflected light is received by the 2" PMT of the MO monitoring system and digitized by a flash ADC. By comparing the reflected and reference signals of the LED pulses, we can monitor the attenuation in the MO. / I will discuss the detailed design and performance of this MO monitoring system and data taken in the AD calibration runs. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Detailed summary in vernacular field only. / Chen, Xiaocong = 應用於大亞灣中微子實驗的一套白油監測系統 / 陳瀟聰. / Thesis (Ph.D.)--Chinese University of Hong Kong, 2013. / Includes bibliographical references (leaves 106-108). / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstracts also in Chinese. / Chen, Xiaocong = ying yong yu Daya Wan zhong wei zi shi yan de yi tao bai you jian ce xi tong / Chen Xiaocong. / Chapter 1 --- Introduction of the Daya Bay Reactor Neutrino Experiment --- p.1 / Chapter 1.1 --- Neutrino Oscillation --- p.1 / Chapter 1.1.1 --- The Discovery of Neutrino --- p.1 / Chapter 1.1.2 --- Oscillation Phenomenology --- p.3 / Chapter 1.1.3 --- Disappearance Probability --- p.4 / Chapter 1.2 --- the Daya Bay Reactor Neutrino Experiment --- p.6 / Chapter 1.2.1 --- Knowledge of the Oscillation Parameters Before Daya Bay --- p.6 / Chapter 1.2.2 --- Overview of the Daya Bay Experiment --- p.8 / Chapter 1.2.3 --- Layout of the Experimental Halls --- p.10 / Chapter 1.2.4 --- Antineutrino Detection --- p.12 / Chapter 1.2.5 --- Relative Measurements --- p.13 / Chapter 1.2.6 --- Significance of θ₁₃ --- p.14 / Chapter 1.2.7 --- The Antineutrino Detector --- p.15 / Chapter 1.2.8 --- Devices on the AD Lid --- p.17 / Chapter 1.3 --- Physics Result from the Daya Bay Experiment --- p.18 / Chapter 2 --- Design and Prototyping of the Mineral Oil Clarity Monitoring System --- p.20 / Chapter 2.1 --- Design --- p.20 / Chapter 2.1.1 --- Motivation of the Mineral Oil Clarity Monitoring System --- p.20 / Chapter 2.1.2 --- Attenuation of Mineral Oil --- p.24 / Chapter 2.1.3 --- MO Clarity Monitoring Scheme --- p.26 / Chapter 2.1.4 --- The Light Source for the MO Clarity Monitoring System --- p.28 / Chapter 2.1.5 --- Hardware inside the MO Clarity Box --- p.31 / Chapter 2.2 --- Prototyping of the Mineral Oil Clarity Monitoring System --- p.34 / Chapter 2.2.1 --- The Setup of the Prototype --- p.34 / Chapter 2.2.2 --- Stability Test of the Prototype --- p.36 / Chapter 2.2.3 --- Tolerance against the Deformation of the AD Lid --- p.39 / Chapter 2.2.4 --- Summary of the Tests on the Prototype --- p.40 / Chapter 3 --- Production and Installation of the Hong Kong Mineral Oil Clarity System --- p.42 / Chapter 3.1 --- Production and Component Tests --- p.42 / Chapter 3.1.1 --- Corner Cube Retroreflector --- p.42 / Chapter 3.1.2 --- Optical Fiber --- p.43 / Chapter 3.1.3 --- Calibration of the Monochromator --- p.45 / Chapter 3.1.4 --- Absolute Gain Measurement of the 2" PMT --- p.46 / Chapter 3.1.5 --- the Flash-ADC --- p.51 / Chapter 3.1.6 --- The Diffuser Ball --- p.53 / Chapter 3.2 --- Onsite Installation --- p.57 / Chapter 3.2.1 --- The Corner Cube --- p.57 / Chapter 3.2.2 --- Installation of the Acrylic Window and Leak Checking . --- p.58 / Chapter 3.2.3 --- Optical Alignment of the Collimator --- p.65 / Chapter 3.2.4 --- Cabling --- p.66 / Chapter 4 --- Operation of the MO Clarity Monitoring System --- p.68 / Chapter 4.1 --- Commissioning of the MO Clarity Monitoring System --- p.68 / Chapter 4.2 --- Data Processing --- p.70 / Chapter 4.2.1 --- Fitting of the PMT Waveforms --- p.71 / Chapter 4.2.2 --- Numerical Integration of the Peaks in the PMT Waveform --- p.75 / Chapter 4.3 --- EMI Pickup Problem --- p.79 / Chapter 4.4 --- MO Clarity Monitoring Results for the Eight ADs --- p.84 / Chapter 4.4.1 --- AD1 --- p.84 / Chapter 4.4.2 --- AD2 --- p.86 / Chapter 4.4.3 --- AD3 --- p.88 / Chapter 4.4.4 --- AD4 --- p.90 / Chapter 4.4.5 --- AD5 --- p.92 / Chapter 4.4.6 --- AD6 --- p.93 / Chapter 4.4.7 --- AD7 --- p.95 / Chapter 4.4.8 --- AD8 --- p.96 / Chapter 4.5 --- Comparison with Simulation Result --- p.98 / Chapter 4.5.1 --- Introduction of the NuWa Simulation --- p.98 / Chapter 4.5.2 --- Simulation Result with Displacement of the Optical Hole --- p.99 / Chapter 4.5.3 --- Possible Cause for the Large Uncertainty in the MO Monitoring Run for Some ADs --- p.100 / Chapter 4.6 --- Precision of the MO Monitoring System and Stability of the MO Attenuation Length --- p.102 / Chapter 5 --- Summary --- p.104 / Bibliography --- p.105

The strong modification to the production of final state hadrons in heavy ion collisions is a key signature of the hot dense medium produced at energies achieved at the Relativistic Heavy Ion Collider (RHIC). Understanding the mechanisms for the parton energy loss responsible for these modifications is challenging and difficult to constrain with straightforward hadronic measurements, making it necessary to turn to more discriminating probes. One example of such a probe is photons produced by partons as they fragment, fragmentation photons, because the production mechanisms for such photons are similar to those for hadrons, but once produced, fragmentation photons will not interact directly with the medium. The challenge of distinguishing the signal for such jet-associate photons out of the large decay background motivates first making such measurements in the simple p + p environment. Combining data collected by the PHENIX detector during 2005 and 2006, the yield for fragmentation photons was measured to be on the order of several percent of all photons measured in association with a hadron with transverse momentum between 2 and 5 GeV/c. The use of two-particle correlations coupled with a sophisticated method for identifying and removing decay photons has made it possible to further study the jet properties of these fragmentation photons, in the form of pout and root mean square jT. These results will help to constrain both the underlying theoretical description of direct photon production in p + p, and modifications expected in heavy ion collisions.

Jet production in relativistic heavy ion collisions is studied using Pb+Pb collisions at a center of mass energy of 2.76 TeV per nucleon. The measurements reported here utilize data collected with the ATLAS detector at the LHC from the 2010 Pb ion run corresponding to a total integrated luminosity of 7 µ b^(-1). The results are obtained using fully reconstructed jets using the anti-k t algorithm with a per-event background subtraction procedure. A centrality-dependent modification of the dijet asymmetry distribution is observed, which indicates a higher rate of asymmetric dijet pairs in central collisions relative to periphal and pp collisions. Simultaneously the dijet angular correlations show almost no centrality dependence. These results provide the first direct observation of jet quenching. Measurements of the single inclusive jet spectrum, measured with jet radius parameters R=0.2, 0.3, 0.4 and 0.5, are also presented. The spectra are unfolded to correct for the finite energy resolution introduced by both detector effects and underlying event fluctuations. Single jet production, through the central-to-peripheral ratio R CP, is found to be suppressed in central collisions by approximately a factor of two, nearly independent of the jet p T. The R CP is found to have a small but significant increase with increasing R, which may relate directly to aspects of radiative energy loss.

Measurements at the Relativistic Heavy Ion Collider (RHIC) have provided indirect measurements of jets in a heavy ion environment using the two- particle correlation method in the presence of a high-pT particle. These measurements have offered insight into the formation of a new state of dense nuclear matter called the Quark-Gluon Plasma (QGP) through the observation of jet quenching. However, the two-particle methodology has also shown to be biased towards di-jet production near the surface of the medium being created. Here, a detailed study using the PHENIX detector is provided, in an attempt to measure a more accurate jet-induced two-particle correlation measurement than previously published and to reduce the bias observed in two-particle correlation measurements. The reduction in surface bias emission is performed via the requirement of two antipodal high-pT particles (a.k.a. "2+1" correlation) in an attempt to control the production point of the di-jet. The measurements made in Au+Au collisions when compared to p+p collisions show that the method provides additional sensitivity to the jet quenching previously observed in two-particle correlation method.

High-pT processes in proton- and deuteron-nucleus collisions at TeV energies are the best presently available way to study the partonic structure of the nucleus in a high-density regime. Jet production over a wide range of phase space can significantly constrain the current knowledge of nuclear parton distribution functions (nPDFs), which are substantially less well understood than the corresponding PDFs in protons and which have only recently begun to be treated in a spatially-dependent way. An accurate knowledge of nPDFs is crucial for a definitive control of perturbative processes in a cold nuclear environment, since high-pT probes are used to quantitatively investigate the hot QCD matter created in ultrarelativistic nucleus-nucleus collisions. Furthermore, jets from low Bjorken-x partons can probe the transition from the dilute to saturated nuclear regimes.

Searches are made for narrow diboson resonances, ZZ and ZW, in the final states llqq and ννqq at ATLAS, with (13.2±0.4) fb−1data collected from pp-collisions with center of mass energy √ s=13 TeV during 2015 and 2016, the first two years of Run 2 of the Large Hadron Collider. The hadronic decay products of the vector boson, V → qq, are reconstructed as jets in the electromagnetic and hadronic calorimeters. When the vector boson is sufficiently boosted the decay products are reconstructed as a single anti-kt R = 1.0 jet. Otherwise two anti-kt R = 0.4 jets are matched to identify the vector boson. The Z boson in its leptonic decay is identified by either reconstructing two electrons in the calorimeters, or opposite sign muons in the muon spectrometer. Limits on the production cross section for 3 benchmark signals, a heavy scalar, a spin-1 heavy vector triplet, and a spin-2 graviton are set in the mass range 300 GeV to 5000 GeV.

A search is presented for new resonances decaying to a pair of boosted Standard Model bosons, WV, where the W boson decays leptonically (W → lν, with l = e, µ) and the other weak boson, V (V=W,Z), decays hadronically (V → qq¯ 0/qq¯, with q, q0 = u, d, c, s, b). The data were collected with the ATLAS detector at the CERN Large Hadron Collider, during the 2015 and 2016 periods of pp collisions, at a center-of-mass energy √s = 13 TeV, and correspond to a total integrated luminosity of 36.1 fb^−1. The hadronic decay of the boosted $V$ boson is reconstructed as a single large-radius jet, and the leptonic decay of the W boson is reconstructed as a lepton and missing transverse energy. The search is sensitive to resonances produced with quark-antiquark fusion, gluon-gluon fusion, and vector-boson fusion. No significant excesses are observed above the Standard Model background prediction. Upper limits on production cross section times branching ratio to WV are set at a 95 % confidence level for selected benchmark signal models. Models of a neutral, narrow scalar boson (spin-0), charged and neutral vector bosons (spin-1) coupling to the Standard Model gauge bosons, and a neutral Randall-Sundrum bulk graviton (spin-2) are considered. The search significantly improves the limits produced in recent searches.

This thesis presents results on the study of electromagnetic (EM) activity in the MicroBooNE Liquid Argon Time Projection Chamber (LArTPC) neutrino detector. The LArTPC detector technology provides bubble-chamber like information on neutrino interaction final states, necessary to perform precision measurements of neutrino oscillation parameters. Accelerator-based oscillation experiments heavily rely on the appearance channel νµ → νe to make such measurements. Identifying and reconstructing the energy of the outgoing electrons from such interactions is therefore crucial for their success. This work focuses on two sources of EM activity: Michel electrons in the 10-50 MeV energy range, and photons from π^0 decay in the ~30-300 MeV range. Studies of biases in the energy reconstruction measurement, and energy resolution are performed. The impact of shower topology at different energies is discussed, and the importance of thresholding and other reconstruction effects on producing an asymmetric and biased energy measurement are highlighted. This work further presents a study of the calorimetric separation of electrons and photons with a focus on the shower energy dependence of the separation power.

Proton-proton collisions at the Large Hadron Collider provide insight into fundamental dynamics at unprecedented energy scales. After the discovery of the Higgs boson by the ATLAS and CMS experiments completed the Standard Model picture of particle physics in 2012, the focus turned to investigation of new phenomena beyond the Standard Model. Variations on Supersymmetry, which has strong theoretical underpinnings and a wide potential particle phenomenology, garnered attention in particular. Preliminary results, however, yielded no new particle discoveries and set limits on the possible physical properties of supersymmetric models. This thesis describes a search for supersymmetric particles that could not have been detected by earlier efforts. The study probes collisions with a center of mass energy of 13 TeV detected by ATLAS from 2015 to 2016 that result in events with a large number of jets. This search is sensitive to decays of heavy particles via cascades, which result in at least seven hadronic jets and some missing energy. Constraints on the properties of reclustered large-radius jets are used to improve the sensitivity. The main Standard Model backgrounds are removed using a template method that extrapolates background behavior from final states with fewer jets. No excess is observed over prediction, so limits are set on supersymmetric particle masses in the context of two different theoretical models. Gluino masses below 1500 and 1600 GeV, respectively, are excluded, a significant extension of the limits set by previous analyses.

No description available.