Thermal energy storage systems, precisely latent thermal energy storage (LTES), are systems capable of recovering and storing thermal energy from waste processes, including hot exhaust gases out of combustion engines, or even renewable sources of energy like solar energy. LTES rely on phase change materials (PCMs) to store a significant amount of thermal energy in a relatively small volume. With limited volume and at almost constant temperature, they are capable of storing a large amount of thermal energy, mainly latent energy. Studies of LTES systems have focused primarily on system and process optimization including transient behavior as well as field performance. A major drawback in the development of the use of PCM in LTES has been the low thermal conductivity characteristic of most PCMs. Thus, there is a need to enhance heat transfer using reliable techniques, with the goal of reducing the charging and discharging times of PCM in LTES systems. Some approaches that have been studied in the past include use of finned tubes, insertion of metal matrix into PCM, and microencapsulation of PCM. The performance of TES configurations in forced convection have been characterized using Reynolds numbers (Re), and Stefan numbers (Ste) of the heat transfer fluid (HTF) for different enhancement techniques. The goal of this study is to experimentally investigate the effectiveness of corrugated PCM panels with high surface-to-volume ratio in forced convection as a function of HTF mass flow rate, charging temperature, and flow direction through a corrugated TES unit. The PCM (octadecane) has been segmented using sealed corrugated panels containing several channels immersed in the HTF stream. With this approach, the author expects that the charging and discharging times will be substantially reduced due to the high surface-to-volume ratio of the PCM panel for heat transfer. Of the three conditions examined, the HTF direction influenced the charging and discharging times the most with significant reductions in these times observed when the HTF flow direction through the TES was upwards. Buoyancy effects, observed at high Stefan numbers, were important during the charging (melting) process and greatly influenced the temperature profiles along each channel. Results indicate that the devised TES is more effective than some other TES systems in the literature.

All energy, wind, water, biofuel and fossil fuel besides nuclear- and tide power originates from the sun. It’s very hard to take full advantage of the huge amount of energy hitting the earth each day from the sun. The suns highest radiation appears often when the energy need reaches its lowest. That’s why it’s very important to be able to store energy over time when the sun doesn’t shine. A large part of energy storage is thermal energy storage, which can either be done sensible, latent or chemical. Another possible thermal storage is a combination of sensible and latent. This exam was aiming to investigate different types of energy storage methods available on the market and a much more detailed analysis for different storage methods with phase change materials (PCM). A new method was designed for a new storage tank suitable for Absolicon Solar Collector AB and their energy park in the city of Härnösand. The methods for this exam were to create a theoretical storage tank suitable to Absolicons Energy Park with some simple calculations. The criteria for the storage tank was to create a storage tank that could provide the district heat in Härnösand with 160 degrees pressurized water and create 160 degrees steam to the industry. The dimensions of the storage tank where chosen by the conditions in Härnösand and from the specific data of Härnösands district heat and from Absolicons new solar collectors. The work temperature of the system were set to 160 degrees which meant that the storage tank would be able to work in those conditions with high temperature. A suitable phase change material and methods for encapsulation of the phase change material suitable for this system was to be found. Small tests were made with a new type of encapsulation for phase change materials in higher temperature. Simple calculations of two types of storage tanks were made. The first storage tank was made with a PCM from PCM products named A164. This PCM was encapsulated with special bags that could handle temperature up to 200 degrees with surrounding rapeseed oil and a copper loop that handled the heat transfer. The second thank was made with the same PCM and encapsulation but with water glycol surrounding the PCM and two types of heat exchangers for the heat transfer. The results from the first tank were that it didn’t work with the district heat. Because a wrong calculation with the schematic of the system made it impossible to connect into the district heat of Härnösand. The only good thing was that it didn’t need to be pressurized because of the rapeseed oil but the bad heat transfer between oil and water made a pressurized tank of water more profitable. The results from the second tank showed that it could produce 160 °C to the district heat for 2 h and 7 minutes. The schematic connection worked and the tank would in the near future be able to connect into the district heat. The result for the encapsulation showed that the bags were able to stand temperatures up to 190 degrees for a short period of time.

In this investigation an electric field was applied to a phase change thermal storage system while it was discharging energy. The phase change material used was octadecane. Octadecane is a high purity dielectric material that has a melting temperature close to room temperature. The material was forced to solidify using a heat exchanger mount below the phase change material, cold water flowed through the heat exchanger to ensure it maintained a constant temperature below the melting temperature of the phase change material. By applying -8kV to 9 electrodes – positioned in the phase change material – and by using the heat exchanger as an electrical ground – an electric field was generated in the phase change material. The electric field caused unbalanced body forces in the fluid which generated electro-convection in the fluid. The system was designed such that electro-convection is the only source of convection in the system to isolate the effects of electro-convection, allowing for the underlying physics of electro-convection to be studied easier. To understand the effects of applying electro-convection, a case where there is no applied voltage on the electrodes was compared to a case where there was -8 kV applied to the electrodes. Experiments showed that the effect of applying electro-convection depends on the initial temperature; however, it was found that the improvement after two hours was less than 10%. For a wall temperature of 8.5℃ and an initial temperature of 50℃ - the melting temperate of octadecane is 28℃- then the maximum enhancement of the energy extracted is 50%, but two hours after the start of the test the enhancement approached zero. For a wall temperature of 8.5℃ and an initial temperature of 30℃, the maximum enhancement is 10% and similarly fall to zero after a few hours of application. A simple analytical model was developed. The experimental and numerical results showed that at the early stages of energy discharge the electro-convection case had a large improvement compared to a pure conduction case, however as time progresses this improvement decreases. The explanation for the trend is that adding convection only increases the rate that energy is taken out of the liquid, thus the maximum improvement is bounded by the amount of sensible energy in the liquid phase change material, once this sensible energy is removed applying electrohydrodynamics is no longer beneficial. / Thesis / Master of Applied Science (MASc)

Phase change materials (PCMs) have the ability to store thermal energy as latent heat over a nearly isothermal temperature range. Compared to sensible heat storage, properly chosen PCMs can store an order of magnitude more energy when undergoing phase change. Organic PCMs present several advantages including their non-corrosive behavior and ability to melt congruently, which result in safe and reliable performance. Because of these qualities, organic PCMs have been proposed for use in latent heat thermal storage systems to increase the energy efficiency or performance of various systems such as cooling and heating in buildings, hot water heating, electronics cooling, and thermal comfort in vehicles. Current performance is hindered by the low thermal conductivity, which significantly limits the rate of charging and discharging. Solutions to this challenge include the insertion of high conductivity nanoparticles and foams to increase thermal transport. However, performance validation remains tied to thermal conductivity and latent heat measurements, instead of more practical metrics of thermal charging performance, stability of the composite, and energy storage cost. This thesis focuses on the use of graphite nanoplatelets and graphite foams to increase the thermal charging performance of organic PCMs. Stability of graphite nanoplatelets in liquid PCM is realized for the first time through the use of dispersants and control of the viscosity, particle distribution, and oxidation. Thermal charging response of stable graphite nanoplatelet composites is compared to graphite foam composites. This study includes a correlation of thermal conductivity and latent heat to material concentration, geometry, and energy storage cost. Additionally, a hybrid PCM storage system of metal foam combined with graphite nanoplatelet PCM is proposed and evaluated under cyclic thermal conditions.

Phase change devices in both optical and electrical formats have been subject of intense research since their discovery by Ovshinsky in the early 1960’s. They have revolutionized the technology of optical data storage and have very recently been adopted for non-volatile semiconductor memories. Their great success relies on their remarkable properties enabling high-speed, low power consumption and stable retention. Nevertheless, their full potential is still yet to be realized. Operations in electrical phase change devices rely on the large resistivity contrast between the crystalline (low resistance) and amorphous (high resistance) structures. The underlying mechanisms of phase transformations and the relation between structural and electrical properties in phase change materials are quite complex and need to be understood more deeply. For this purpose, we compare different approaches to mathematical modelling that have been suggested to realistically simulate the crystallization and amorphization of phase change materials. In this thesis the recently introduced Gillespie Cellular Automata (GCA) approach is used to obtain direct simulation of the structural phases and the electrical states of phase change materials and devices. The GCA approach is a powerful technique to understand the nanostructure evolution during the crystallization (SET) and amorphization (RESET) processes in phase change devices over very wide length scales. Using this approach, a detailed study of the electrical properties and nanostructure dynamics during SET and RESET processes in a PCRAM cell is presented. Besides the possibility of binary storage in phase change memory devices, there is a wider and far-reaching potential for using them as the basis for new forms of arithmetic and cognitive computing. The origin of such potential lies in a previously under-explored property, namely accumulation which has the potential to implement basic arithmetic computations. We exploit and explore this accumulative property in films and devices. Furthermore, we also show that the same accumulation property can be used to mimic a simple integrate and fire neuron. Thus by combining both a phase change cell operating in the accumulative regime for the neural body and a phase change cell in the multilevel regime for the synaptic weighting an artificial neuromorphic system can be obtained. This may open a new route for the realization of phase change based cognitive computers. This thesis also examines the relaxation oscillations observed under suitable bias conditions in phase change devices. The results presented are performed through a circuit analysis in addition with a generation and recombination mechanism driven by the electric field and carrier densities. To correctly model the oscillations we show that it is necessary to include a parasitic inductance. Related to the electrical states of phase change materials and devices is the threshold switching of the amorphous phase at high electric fields and recent work has suggested that such threshold switching is the result of field-induced nucleation. An electric field induced nucleation mechanism is incorporated into the GCA approach by adding electric field dependence to the free energy of the system. Using results for a continuous phase change thin films and PCRAM devices we show that a purely electronic explanation of threshold switching, rather than field-induced nucleation, provides threshold fields closer to experimentally measured values.

A prototype thermal storage system, using phase change materials, was developed for a novel electric vehicle climate conditioning application. The proposed system consists of a heat transfer fluid circulating between either an on-board hot or cold thermal storage unit, which we refer to as thermal battery, and a liquid-air heat exchanger that provides heat exchange with the incoming air to the vehicle cabin. The research presented herein focuses primarily on the development of the on-board system and hot battery. While the air conditioning system was developed strictly for laboratory use, it was designed to meet application realistic performance metrics, e.g., a heat dissipation rate of 2 kW. The prototype was tested with three phase change materials: paraffin wax, xylitol, and erythritol. Furthermore, a full system thermodynamic model was developed to predict thermal performance that features semi-analytic solution to the coupled forced convection and phase change conduction heat transfer. Modeling results are compared against a numerical benchmark as well as our own experimental data. / text

abstract: In recent years, 40% of the total world energy consumption and greenhouse gas emissions is because of buildings. Out of that 60% of building energy consumption is due to HVAC systems. Under current trends these values will increase in coming years. So, it is important to identify passive cooling or heating technologies to meet this need. The concept of thermal energy storage (TES), as noted by many authors, is a promising way to rectify indoor temperature fluctuations. Due to its high energy density and the use of latent energy, Phase Change Materials (PCMs) are an efficient choice to use as TES. A question that has not satisfactorily been addressed, however, is the optimum location of PCM. In other words, given a constant PCM mass, where is the best location for it in a building? This thesis addresses this question by positioning PCM to obtain maximum energy savings and peak time delay. This study is divided into three parts. The first part is to understand the thermal behavior of building surfaces, using EnergyPlus software. For analysis, a commercial prototype building model for a small office in Phoenix, provided by the U.S. Department of Energy, is applied and the weather location file for Phoenix, Arizona is also used. The second part is to justify the best location, which is obtained from EnergyPlus, using a transient grey box building model. For that we have developed a Resistance-Capacitance (RC) thermal network and studied the thermal profile of a building in Phoenix. The final part is to find the best location for PCMs in buildings using EnergyPlus software. In this part, the mass of PCM used in each location remains unchanged. This part also includes the impact of the PCM mass on the optimized location and how the peak shift varies. From the analysis, it is observed that the ceiling is the best location to install PCM for yielding the maximum reduction in HVAC energy consumption for a hot, arid climate like Phoenix. / Dissertation/Thesis / Masters Thesis Mechanical Engineering 2018

abstract: Buildings consume a large portion of the world's energy, but with the integration of phase change materials (PCMs) in building elements this energy cost can be greatly reduced. The addition of PCMs into building elements, however, becomes a challenge to model and analyze how the material actually affects the energy flow and temperatures in the system. This research work presents a comprehensive computer program used to model and analyze PCM embedded wall systems. The use of the finite element method (FEM) provides the tool to analyze the energy flow of these systems. Finite element analysis (FEA) can model the transient analysis of a typical climate cycle along with nonlinear problems, which the addition of PCM causes. The use of phase change materials is also a costly material expense. The initial expense of using PCMs can be compensated by the reduction in energy costs it can provide. Optimization is the tool used to determine the optimal point between adding PCM into a wall and the amount of energy savings that layer will provide. The integration of these two tools into a computer program allows for models to be efficiently created, analyzed and optimized. The program was then used to understand the benefits between two different wall models, a wall with a single layer of PCM or a wall with two different PCM layers. The effect of the PCMs on the inside wall temperature along with the energy flow across the wall are computed. The numerical results show that a multi-layer PCM wall was more energy efficient and cost effective than the single PCM layer wall. A structural analysis was then performed on the optimized designs using ABAQUS v. 6.10 to ensure the structural integrity of the wall was not affected by adding PCM layer(s). / Dissertation/Thesis / M.S. Civil and Environmental Engineering 2013

abstract: Manufacture of building materials requires significant energy, and as demand for these materials continues to increase, the energy requirement will as well. Offsetting this energy use will require increased focus on sustainable building materials. Further, the energy used in building, particularly in heating and air conditioning, accounts for 40 percent of a buildings energy use. Increasing the efficiency of building materials will reduce energy usage over the life time of the building. Current methods for maintaining the interior environment can be highly inefficient depending on the building materials selected. Materials such as concrete have low thermal efficiency and have a low heat capacity meaning it provides little insulation. Use of phase change materials (PCM) provides the opportunity to increase environmental efficiency of buildings by using the inherent latent heat storage as well as the increased heat capacity. Incorporating PCM into concrete via lightweight aggregates (LWA) by direct addition is seen as a viable option for increasing the thermal storage capabilities of concrete, thereby increasing building energy efficiency. As PCM change phase from solid to liquid, heat is absorbed from the surroundings, decreasing the demand on the air conditioning systems on a hot day or vice versa on a cold day. Further these materials provide an additional insulating capacity above the value of plain concrete. When the temperature drops outside the PCM turns back into a solid and releases the energy stored from the day. PCM is a hydrophobic material and causes reductions in compressive strength when incorporated directly into concrete, as shown in previous studies. A proposed method for mitigating this detrimental effect, while still incorporating PCM into concrete is to encapsulate the PCM in aggregate. This technique would, in theory, allow for the use of phase change materials directly in concrete, increasing the thermal efficiency of buildings, while negating the negative effect on compressive strength of the material. / Dissertation/Thesis / M.S. Civil Engineering 2013

Phase Change Materials have been the subject of increased research in modern times. Phase Change Materials, abbreviated as PCMs, are being used in a variety of applications in the energy conservation world. In this study, the effect of PCMs on a residential building’s energy consumption was evaluated at different locations across the United States and compared to the standard building at the same locations. An average American residential building was designed and modeled in SketchUp software. The building was evaluated for energy consumption at different locations across the United States using weather data for each chosen location. After the baseline results were collected, the building was re-evaluated, under the same conditions, with a Heptadecane embedded in the exterior walls as the chosen PCM for this study. The results of this study show that Phase Change Materials have a wide-ranging effect on the energy consumption of the designed building. Addition of the PCM to the building walls decreased total energy usage, over the course of a year, by 3.02 – 6.72%, depending on the location.