Ever growing demands for higher data rate and bandwidth are pushing extremely high data rate wireless applications to millimeter-wave band (30-300GHz), where sufficient bandwidth is available and high data rate wireless can be achieved without using complex modulation schemes. In addition to the communication applications, millimeter-wave band has enabled novel short range and long range radar sensors for automotive as well as high resolution imaging systems for medical and security. Small size, high gain antennas, unlicensed and worldwide availability of released bands for communication and a number of other applications are other advantages of the millimeter-wave band. The major obstacle for the wide deployment of commercial wireless and radar systems in this frequency range is the high cost and bulky nature of existing GaAs- and InP-based solutions. In recent years, with the rapid scaling and development of the silicon-based integrated circuit technologies such as CMOS and SiGe, low cost technologies have shown acceptable millimeter-wave performance, which can enable highly integrated millimeter-wave radio devices and reduce the cost significantly. Furthermore, at this range of frequencies, on-chip antenna becomes feasible and can be considered as an attractive solution that can further reduce the cost and complexity of the radio package. The propagation channel challenges for the realization of low cost and reliable silicon-based communication devices at millimeter-wave band are severe path loss as well as shadowing loss of human body. Silicon technology challenges are low-Q passive components, low breakdown voltage of active devices, and low efficiency of on-chip antennas. The main objective of this thesis is to investigate and to develop antenna and front-end for cost-effective silicon based millimeter-wave phased array radio architectures that can address above challenges for short range, high data rate wireless communication as well as radar applications. Although the proposed concepts and the results obtained in this research are general, as an important example, the application focus in this research is placed on the radio aspects of emerging 60 GHz communication system. For this particular but extremely important case, various aspects of the technology including standard, architecture, antenna options and indoor propagation channel at presence of a human body are studied. On-chip dielectric resonator antenna as a radiation efficiency improvement technique for an on-chip antenna on low resistivity silicon is presented, developed and proved by measurement. Radiation efficiency of about 50% was measured which is a significant improvement in the radiation efficiency of on-chip antennas. Also as a further step, integration of the proposed high efficiency antenna with an amplifier in transmit and receive configurations at 30 GHz is successfully demonstrated. For the implementation of a low cost millimeter-wave array antenna, miniaturized, and efficient antenna structures in a new integrated passive device technology using high resistivity silicon are designed and developed. Front-end circuit blocks such as variable gain LNA, continuous passive and active phase shifters are investigated, designed and developed for a 60GHz phased array radio in CMOS technology. Finally, two-element CMOS phased array front-ends based on passive and active phase shifting architectures are proposed, developed and compared.

Wireless Mesh Networks are increasingly becoming popular as low cost alternatives to wired networks for providing broadband access to users (the last mile connectivity). A key challenge in deploying wireless mesh networks is designing networks with sufficient capacity to meet user demands. Accordingly, researchers have explored various schemes in an effort to build high throughput mesh networks. One of the key technologies that is often employed by researchers to build high throughput wireless mesh networks (WMN) is equipping nodes with smart antennas. By exploiting the advantages of reduced interference and longer transmission paths, smart antennas have been shown to significantly increase network throughput in WMN. However, there is a need to identify and establish an upper-bound on the maximum throughput that is achievable by using smart antennas equipped WMN. Such a bound on throughput is important for several reasons, the most important of which is identifying the services that can be supported by these technologies. This thesis begins with a focus on establishing this bound. Clearly, it is evident that smart-antennas cannot increase network throughput beyond a certain limit for various reasons including the limitations imposed by existing smart an- tenna technology itself. However with the spiralling demand for broadband access, schemes must be explored that can increase network throughput beyond the limit imposed by smart antennas. An interesting and robust method to achieve this increased throughput is by en- abling multiple gateways within the network. Since, the position of these gateways within the network bears a significant influence on network performance, techniques to “opti- mally” place these gateways within the network must be evolved. The study of multiple gateway placement in multi-hop mesh networks forms the next focus of this study. This thesis ends with a discussion on further work that is necessary in this domain.

Phased arrays eliminate the problems of mechanical steering by using fast and reliable electronic components for steering the main beam. Modeling and simulation of beam steering for 1D and 2D arrays is the aspect that is considered in this thesis. A 1D array with 4 elements and a 2D array with 16 elements are studied in the X-band (8-12 GHz). The RF front-end of a phased array radar is modeled by means of ADS Momentum (Advanced design system).

Wireless Mesh Networks are increasingly becoming popular as low cost alternatives to wired networks for providing broadband access to users (the last mile connectivity). A key challenge in deploying wireless mesh networks is designing networks with sufficient capacity to meet user demands. Accordingly, researchers have explored various schemes in an effort to build high throughput mesh networks. One of the key technologies that is often employed by researchers to build high throughput wireless mesh networks (WMN) is equipping nodes with smart antennas. By exploiting the advantages of reduced interference and longer transmission paths, smart antennas have been shown to significantly increase network throughput in WMN. However, there is a need to identify and establish an upper-bound on the maximum throughput that is achievable by using smart antennas equipped WMN. Such a bound on throughput is important for several reasons, the most important of which is identifying the services that can be supported by these technologies. This thesis begins with a focus on establishing this bound. Clearly, it is evident that smart-antennas cannot increase network throughput beyond a certain limit for various reasons including the limitations imposed by existing smart an- tenna technology itself. However with the spiralling demand for broadband access, schemes must be explored that can increase network throughput beyond the limit imposed by smart antennas. An interesting and robust method to achieve this increased throughput is by en- abling multiple gateways within the network. Since, the position of these gateways within the network bears a significant influence on network performance, techniques to “opti- mally” place these gateways within the network must be evolved. The study of multiple gateway placement in multi-hop mesh networks forms the next focus of this study. This thesis ends with a discussion on further work that is necessary in this domain.

Experimental aeroacoustic research was conducted on a wind turbine specific airfoil at low Reynolds numbers. The goal of this thesis was to study trailing edge noise generation from the airfoil and investigate correlations between the noise and the flow field. Before experiments were performed the current wind tunnel had to be modified in order to make it more suitable for aeroacoustic tests. Sound absorbing foam was added to the inside of the tunnel to lower the background noise levels and turbulence reduction screens were added which lowered the turbulence. An S822 airfoil was chosen because it is designed for low Reynolds flows attainable in the wind tunnel which are on the order of 104. Smoke wire flow visualization was used to gain insight into the airfoil wake development and oil film flow visualization was used to qualitatively assess the boundary layer development. Laser Doppler anemometry (LDA) was used to measure two components of velocity at high data rates in the airfoil wake. Wake profiles were measured in addition to single point measurements to determine the velocity spectrum. A microphone was mounted inside the test section in order to measure the trailing edge noise. Initial plans included measuring the trailing edge noise with a microphone array capable of quantifying and locating noise sources. Although an array was built and beamforming code was written it was only used in preliminary monopole source tests. Oil film results showed the behaviour of the boundary layer to be consistent with previous low Reynolds number experiments. LDA results revealed sharp peaks in the velocity spectra at 1100 Hz from U0 = 15–24 m/s, and 3100 and 3800 Hz, from U0 = 25–35 m/s, which were inconsistent with vortex shedding results of previous researchers. Also present were a series of broad peaks in the spectra that increase from 1200–1700 Hz in the U0 = 25–35 m/s range. The shedding frequency from the smoke wire flow visualization was calculated to be 1250 Hz at U0 = 26 m/s. These sharp peaks were also present in the acoustic spectrum. It was reasoned that these peaks are due to wind tunnel resonance which is a common occurrence in hard wall wind tunnels. In particular the tone at 1100 Hz is due to a standing wave with a wavelength equal to half the tunnel width. The shedding frequency from the smoke wire flow visualization was calculated to be 1100 Hz at U0 = 20 m/s. These tones exhibited a “ladder-like” relationship with freestream velocity, another aspect indicative of wind tunnel resonance. It was reasoned that the wind tunnel resonance was forcing the shedding frequency of the airfoil in the U0 = 15–24 m/s range, and in the U0 = 25–35 m/s range, the shedding frequency corresponded to the broad peaks in the LDA spectra.

<p>This dissertation examines the use of artificial structured materials -- known as metamaterials -- in two antenna applications in which conventional dielectric materials are otherwise used. In the first application, the use of metamaterials to improve the impedance matching of planar phased array antennas over a broad range of scan angles is explored. A phased array antenna is composed of an array of antenna elements and enables long-distance signal propagation by directional radiation. The direction of signal propagation is defined as the scan angle. The power transmission ratio of a phased array is the ratio of the radiated power to the input power, and depends on the scan angle. The variation in the power transmission ratio is due to the different mutual coupling contributions between antenna elements at different scan angles. An optimized stack of dielectric layers, known as a wide-angle impedance matching layer (WAIM), is used to optimize the power transmission ratio profile over a broad range of scan angles. In this work, the use of metamaterials to design anisotropic WAIMs with access to a larger range of constitutive parameters -- including magnetic permeability -- to offer an improved power transmission ratio at a broad range of scan angles is investigated. </p> <p>In the second antenna application, a strategy to create maximally transmissive and minimally reflective electromagnetic radome materials using embedded metamaterial inclusions is introduced. A radome is a covering used to protect an antenna from weather elements or provide structural function such as the prevention of aerodynamic drag. A radome should be made from a fully transparent and non-refractive material so that radiated fields from and to the enclosed antenna are not disrupted. The aim of this research was to demonstrate that embedded metamaterial inclusions can be used to isotropically adjust the dielectric properties of a composite material to a desired value. This strategy may lead to the creation of a structural material with electromagnetic properties close to air, thus reducing the detrimental scattering effects often associated with conventional radome materials.</p> <p>Chapter 1 introduces the concept of metamaterials and discusses the use of subwavelength metallic structures to artificially engineer constitutive parameters such as permeability of permittivity. In Chapter 2, the analytical formulations that enable the characterization of the transmission performance of a planar phased array covered with anisotropic impedance matching layers are developed. Chapter 3 discusses the design rules that must govern the design parameters of anisotropic WAIMs realizable using metamaterials, and also presents examples of anisotropic impedance matching layers that provide a maximum power transmission ratio for most scan angles. In addition, numerical and experimental results on a metamaterial placed over a phased array are presented. In Chapter 4, the feasibility of using metamaterials to realize a minimally transparent and fully transmissive radome material is numerically investigated. In Chapter 5, experimental results that corroborate earlier numerical simulation results are analyzed.</p> / Dissertation

This thesis presents a novel monolithic phased array implemented using the RF MEMS technology. The structure, which is designed at 15 GHz, consists of four linearly placed microstrip patch antennas, 3-bit distributed RF MEMS low-loss phase shifters, and a corporate feed network. The RF MEMS phase shifter employed in the system consists of three sections with a total of 28 unit cells, and it occupies an area of 22.4 mm &amp / #61620 / 2.1 mm. The performance of the phase shifters is improved using high-Q metal-air-metal capacitors in addition to MEMS switches as loading elements on a high-impedance coplanar waveguide transmission line. The phased array is fabricated monolithically using an in-house surface micromachining process, where a 1.2-&amp / #61549 / m thick gold structural layer is placed on a 500-&micro / m thick glass substrate with a capacitive gap of 2 &amp / #61549 / m. The fabrication process is simple, requires only 6 masks, and allows the implementation of various RF MEMS components on the same substrate, such as RF MEMS switches and phase shifters. The fabricated monolithic phased array occupies an area of only 6 cm &amp / #61620 / 5 cm. The measurement results show that the phase shifter can provide nearly 20&amp / #61616 / /50&amp / #61616 / /95&amp / #61616 / phase shifts and their eight combinations at the expense of 1.5 dB average insertion loss at 15 GHz. The phase shifters can be actuated with 16 V, while dissipating negligible power due to its capacitive operation. It is also shown by measurements that the main beam can be steered to 4&amp / #61616 / and 14&amp / #61616 / by suitable settings of the RF MEMS phase shifters.

Experimental measurements and numerical simulations have been performed on copper and aluminum microchannel heatsinks of 300, 420, 500, and 900 &amp / #956 / m channel widths. The heatsinks have been designed specifically for use with T/R (transmit/receive) module cooling applications of military phased array radars. An analytical calculation was also performed to aid in the design methodology. Distilled water was used as the coolant with flow rates ranging from 0.50 lpm (liters per minute) to 1.00 lpm. Local heat fluxes as high as 100 W/cm2 were tested. Upon completion of the experiments, the thermally best performing specimen, the 300 &amp / #956 / m copper specimen, yielded a maximum temperature rise of 26.1 &deg / C between the heat load and coolant inlet, at a coolant flow rate of 1.00 lpm and local heat flux of 100 W/cm2, leading to a thermal resistance of 0.63 &deg / C/W. The pressure drop measured across the heatsink under these conditions was 0.030 bar. Numerical simulations were carried out using the commercial Computational Fluid Dynamics (CFD) software FLUENT&reg / . Effects of thermal interface layers and heat spreading due to the localized heat load were investigated. Simulation results for temperature were seen to agree fairly well with experimental data as long as thermal interface layers were accounted for. The study showed that the T/R modules of military phased array radars, dissipating as high as 100 W/cm2 locally, could be cooled within the limits of the harsh environmental conditions required of military applications with moderate pressure drops.

Experimental measurements are conducted on uninterrupted and interrupted aluminum microchannel heat sinks of 300, 500, 600 and 900 &mu / m channel widths. Two different versions of interrupted channels are tested / with single interruption and with 7 interruptions. Distilled water is used as the working fluid and tests are conducted at volumetric flow rates in a range of 0.5-1.1 lpm. Thermoelectric foils are used to supply uniformly distributed heat load to the heat sinks such that for all the tests the heat removed by water is kept constant at 40 W. Pressure drop and temperature increase are measured along the channels of different configurations for a number of different flow rates. For the interrupted channels thermal boundary layers re-initialize at the leading edge of each interrupted fin, which decreases the overall boundary layer thickness. Also the flow has been kept as developing, which results in better heat transfer performance. Due to the separation of the flow into branches, secondary flows appear which improves the mixing of the stream. Advanced mixing of the flow also enhances the thermal performance. In the experiments, it is observed that interruption of channels improved the thermal performance over the uninterrupted counterparts up to 20% in average Nusselt number, for 600 micron-wide channels. The improvement of average Nusselt number between the single interrupted and multi interrupted channels reached a maximum value of 56% for 500 micron-wide channels. This improvement did not cause a high pressure drop deviation between the uninterrupted and interrupted microchannels even for the maximum volumetric flow rate of 1.1 lpm. Highest pressure drop through the channels was measured as 0.07 bar, which did not require to change the pump. In the tests, maximum temperature difference between the inlet of the fluid and the base of the channel is observed as 32.8&deg / C, which is an acceptable value for electronic cooling applications.

This dissertation introduces new technologies and techniques for low-cost phased arrays and scanning antennas. Special emphasis is placed on new approaches for low-cost millimeter-wave beam control. Several topics are covered. A novel reconfigurable grating antenna is presented for low-cost millimeter-wave beam steering. The versatility of the approach is proven by adapting the design to dual-beam and circular-polarized operation. In addition, a simple and accurate procedure is developed for analyzing these antennas. Designs are presented for low-cost microwave/millimeter-wave phased-array transceivers with extremely broad bandwidth. The target applications for these systems are mobile satellite communications and ultra-wideband radar. Monolithic PIN diodes are a useful technology, especially suited for building miniaturized control components in microwave and millimeter-wave phased arrays. This dissertation demonstrates a new strategy for extracting bias-dependent small-signal models for monolithic PIN diodes. The space solar-power satellite (SPS) is a visionary plan that involves beaming electrical power from outer space to the earth using a high-power microwave beam. Such a system must have retrodirective control so that the high-power beam always points on target. This dissertation presents a new phased-array architecture for the SPS system that could considerably reduce its overall cost and complexity. In short, this dissertation presents technologies and techniques that reduce the cost of beam steering at microwave and millimeter-wave frequencies. The results of this work should have a far-ranging impact on the future of wireless systems.