No description available.

Metal-halide perovskites show great promise as solution-processable semiconductors for efficient solar cells and LEDs. In particular, the diffusion range of photogenerated carriers is unexpectedly long and the luminescence yield is remarkably high. While much effort has been made to improve device performance, the barriers to improving charge transport and recombination properties remain unidentified. I first explore charge transport by investigating a back-contact architecture for measurement. In collaboration with the Snaith group at Oxford, we develop a new architecture to isolate charge carriers. We prepare thin films of perovskite semiconductors over laterally-separated electron- and hole-selective materials of SnOₓ and NiOₓ, respectively. Upon illumination, electrons (holes) generated over SnOₓ (NiOₓ) rapidly transfer to the buried collection electrode, leaving holes (electrons) to diffuse laterally as majority carriers in the perovskite layer. We characterise charge transport parameters of electrons and holes, separately, and demonstrate that grain boundaries do not prevent charge transport. Our results show that the low mobilities found in applied-field techniques do not reflect charge diffusivity in perovskite solar cells at operating conditions. We then use the back-contact architecture to investigate recombination under large excess of one charge carrier type. Recombination velocities under these conditions are found to be below 2 cm s⁻¹, approaching values of high quality silicon and an order of magnitude lower than under common bipolar conditions. Similarly, diffusion lengths of electrons and holes exceed 12 μm, an order of magnitude higher than reported in perovskite devices to date. We report back-contact solar cells with short-circuit currents as high as 18.4 mA cm⁻², giving 70% external charge-collection efficiency. We then explore the behaviour of charge carriers in continuously illuminated metal-halide perovskite devices. We show that continuous illumination of perovskite devices gives rise to a segregated charge carrier population, and we find that the distance photo-induced charges travel increases significantly under these conditions. Finally, we examine intermittancy in the photoluminescence intensity of metal-halide perovskite films.

Yes / The application of photoelectrochemical methods presents the researcher with a powerful set of versatile tools by which photoactive materials, such as semiconductor quantum dots, at conductive interfaces may be interrogated. While the range of photoelectrochemical techniques available is quite large, it is surprising that very few have found their way into common usage within the nanoparticle community. Here a number of photoelectrochemical techniques and the principles upon which they are based are introduced. A short discussion on the criticality of ensuring the nanoparticles are reliably anchored to the substrate is followed by an introduction to the basic set of equipment required in order to enable the investigator to undertake such experiments. Subsequently the four techniques of transient photocurrent response to square wave illumination, photocurrent spectroscopy, intensity modulated photocurrent spectroscopy (IMPS) and intensity modulated photovoltage spectroscopy (IMVS) are introduced. Finally, the information that can be acquired using such techniques is provided with emphasis being placed on a number of case studies exemplifying the application of photoelectrochemical techniques to nanoparticles at interfaces, in particular optically transparent electrodes.

Ausgangspunkt dieser Arbeit war die Frage, inwieweit die zur Herstellung von Compositmaterialien aus leitfähigen Polymerfilmen (Polythiophen, Polypyrrol) und Metalloxidschichten (anodisch oxidiertes Titan, chemisch oxidiertes Silicium bzw. Aluminium) entwickelte Präparationsmethode auf die Herstellung hybrider Core - Shell - Partikel (Core: Metalloxidpartikel; Shell: leitfähiges Polymer) übertragbar ist. Die erfolgreiche Beschichtung dispergierter Oxidpartikel mit leitfähigen Poly- meren zeigte, dass nicht nur eine analoge Verfahrensweise (Adsorption des Monomers auf der Substratoberfläche und anschließende Zugabe des Oxidationsmittels) verwendet werden konnte, sondern dass bei der Pulverbeschichtung infolge der großen spezifischen Oberfläche der Materialien auch ohne Einsatz spezieller Haftvermittler, hervorragende Schichtqualitäten (hohe Haftfestigkeit, hoher Be- deckungsgrad) erreicht wurden, und die auf diesem Wege hergestellten Verbundmaterialien in Pulverform in beliebiger Menge, Partikelgröße und Zusam-mensetzung verfügbar waren. Der durch die Verkapselung der Oxidteilchen mit intrinsich leitfähigen Polymeren bewirkte enge Kontakt zwischen Polymer- und Oxidphase und die auf diesem Wege realisierte Oberflächenmodifizierung führte zu einem im Vergleich zu den reinen Komponenten wesentlich veränderten Eigenschaftsspektrum. Durch die Herstellung von Compositen waren die leitfähigen Polymere leichter dispergierbar, und konnten kathaphoretisch in guter Qualität, auch auf großen Substratflächen abgeschieden werden. / Starting with the question about the possibility of producing composites based on conducting polymer films (polythiophene, polypyrrole) and metal oxide layers (anodically oxidized titanium, chemical oxidized silicon or aluminium) it was the goal of this work to transfer and modify this method for the preparation of hybrid core - shell - particles (core: metal oxide particle; shell: conducting polymer). By the successfully covering of dispersed oxide particles it was shown, that not only an analogous procedure (adsorption of the monomer on the substrate surface and the following addition of an oxidant) can be used, but that in the case of powder covering because of the high specific surface area of the oxide powders, outstanding layer qualities without using adhesion promotors can be produced. Following this way, powder-like compound materials can be ordered and designed in any quantity, particle size and composition. Through the encapsulation of the oxide particles with intrinsic conducting polymers a narrow contact between the polymer and the oxide phase and a surface modification were made by a very simple way. By this surface modification a totally different behaviour of the composites, compared to their components was realized. The producing of composites allowes a better dispersibility of conducting polymers and their cathaphoretically deposition with a good quality, also on larger substrate surfaces.

Conducting polymer nanocomposites composed of metal oxides and polythiophene was synthesized by chemical polymerization in colloidal suspensions. The electrochemical and photoelectrochemical properties of such nanocomposites have been studied. For these investigations films of nanocomposites were prepared by an electrophoretic deposition process. The deposition process was studied in greater detail and kinetic details were determined. The high voltage electrophoretic deposition process was combined with a quartz crystal microbalance (QCM). Then the films were characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and photocurrent spectroscopy.

This work concerns with today's challenges of photoelectrical characterization methods in the research and development of thin film silicon solar cells. Relevant results are obtained only when photocurrent spectroscopy and measurement of current-voltage characteristics, are applied on the real structures that can however be multi-layered, multi-junction devices with nanostructured interfaces. Analytical and numerical optical models comprising light scattering are used for analysis of light absorption and for evaluation of optical absorption coefficient of silicon layers in sub-gap region. The slope of absorption edge and residual absorption in mid-gap indicate material disorder and defect density. Based on the investigation of electrical interaction between sub-cells in the dual-junction solar cell we developed new methods of evaluation of photocurrent spectra and current-voltage characteristics individually for each sub-cell with no need to contact them directly. Usability of Fourier Transform Photocurrent Spectroscopy as a robust method for photocurrent spectroscopy of amorphous silicon is thoroughly analyzed here. The issues of frequency dependence are addressed in detail and comparison with photothermal deflection spectroscopy is made.

No description available.

No / The objective of this review is to provide an overview concerning what the authors believe to be the most important photoelectrochemical techniques for the study of semiconductor nanoparticles. After a short historical background and a brief introduction to the area of photoelectrochemistry, the working principles and experimental setups of the various static and dynamic techniques are presented. Experimental details which are of crucial importance for their correct execution are emphasized, and applications of the techniques as found in the recent research literature as applied to semiconductor nanoparticles are illustrated.

Ausgangspunkt dieser Arbeit war die Frage, inwieweit die zur Herstellung von Compositmaterialien aus leitfähigen Polymerfilmen (Polythiophen, Polypyrrol) und Metalloxidschichten (anodisch oxidiertes Titan, chemisch oxidiertes Silicium bzw. Aluminium) entwickelte Präparationsmethode auf die Herstellung hybrider Core - Shell - Partikel (Core: Metalloxidpartikel; Shell: leitfähiges Polymer) übertragbar ist. Die erfolgreiche Beschichtung dispergierter Oxidpartikel mit leitfähigen Poly- meren zeigte, dass nicht nur eine analoge Verfahrensweise (Adsorption des Monomers auf der Substratoberfläche und anschließende Zugabe des Oxidationsmittels) verwendet werden konnte, sondern dass bei der Pulverbeschichtung infolge der großen spezifischen Oberfläche der Materialien auch ohne Einsatz spezieller Haftvermittler, hervorragende Schichtqualitäten (hohe Haftfestigkeit, hoher Be- deckungsgrad) erreicht wurden, und die auf diesem Wege hergestellten Verbundmaterialien in Pulverform in beliebiger Menge, Partikelgröße und Zusam-mensetzung verfügbar waren. Der durch die Verkapselung der Oxidteilchen mit intrinsich leitfähigen Polymeren bewirkte enge Kontakt zwischen Polymer- und Oxidphase und die auf diesem Wege realisierte Oberflächenmodifizierung führte zu einem im Vergleich zu den reinen Komponenten wesentlich veränderten Eigenschaftsspektrum. Durch die Herstellung von Compositen waren die leitfähigen Polymere leichter dispergierbar, und konnten kathaphoretisch in guter Qualität, auch auf großen Substratflächen abgeschieden werden. / Starting with the question about the possibility of producing composites based on conducting polymer films (polythiophene, polypyrrole) and metal oxide layers (anodically oxidized titanium, chemical oxidized silicon or aluminium) it was the goal of this work to transfer and modify this method for the preparation of hybrid core - shell - particles (core: metal oxide particle; shell: conducting polymer). By the successfully covering of dispersed oxide particles it was shown, that not only an analogous procedure (adsorption of the monomer on the substrate surface and the following addition of an oxidant) can be used, but that in the case of powder covering because of the high specific surface area of the oxide powders, outstanding layer qualities without using adhesion promotors can be produced. Following this way, powder-like compound materials can be ordered and designed in any quantity, particle size and composition. Through the encapsulation of the oxide particles with intrinsic conducting polymers a narrow contact between the polymer and the oxide phase and a surface modification were made by a very simple way. By this surface modification a totally different behaviour of the composites, compared to their components was realized. The producing of composites allowes a better dispersibility of conducting polymers and their cathaphoretically deposition with a good quality, also on larger substrate surfaces.

Conducting polymer nanocomposites composed of metal oxides and polythiophene was synthesized by chemical polymerization in colloidal suspensions. The electrochemical and photoelectrochemical properties of such nanocomposites have been studied. For these investigations films of nanocomposites were prepared by an electrophoretic deposition process. The deposition process was studied in greater detail and kinetic details were determined. The high voltage electrophoretic deposition process was combined with a quartz crystal microbalance (QCM). Then the films were characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and photocurrent spectroscopy.