No description available.

No description available.

No description available.

No description available.

No description available.

No description available.

This thesis addresses the issue of a potential future microelectronics technology, namely the possibility of utilising the optical properties of nanocrystalline silicon for optoelectronic circuits. The subject is subdivided into three chapters. Chapter 1 is an introduction. It formulates the oncoming problem for microelectronic development, explains the basics of Integrated Optoelectronics, introduces porous silicon as a new light-emitting material and gives a brief review of other competing light-emitting material systems currently under investigation. Examples of existing porous silicon devices are given. Chapter 2 reviews the basic physics relevant to the subject of this thesis and informs on the present situation in this field of research, including both experimental and theoretical knowledge gained up-to-date. The chapter provides the necessary background for correct interpretation of the results reported in Chapter 3 and for a realistic decision on the direction for future work. Chapter 3 describes my own experimental and computational results within the framework of the subject, obtained at De Montfort University. These include: onestep preparation of laterally structured porous silicon with photoluminescence and microscopy characterisation, Raman spectroscopy of porous silicon, a polarisation study of the photoluminescence from porous silicon, computer simulations of the conductivity of two-component media and of laser focused atomic deposition for nanostructure fabrication. Thus, this thesis makes a dual contribution to the chosen field: it summarises the present knowledge on the possibility of utilising optical properties of nanocrystalline silicon in silicon-based electronics, and it reports new results within the framework of the subject. The main conclusion is that due to its promising optoelectronic properties nanocrystalline silicon remains a prospective competitor for the cheapest and fastest microelectronics of the next century.

No description available.

The key challenge for a nanomaterial based sensor is how to synthesize in bulk quantity and fabricate an actual device with insightful understanding of operational mechanisms during performance. I report here effective, controllable methods that exploit the concepts of the "green approach" to synthesize two different one-dimensional nanostructures, including tin oxide nanowires and carbon nanotubes. The syntheses are followed by product characterization and sensing device fabrications as well as sensor performance understanding at the molecular level. Sensor-analyte response and recovery kinetics are also presented. The first part of the thesis describes bulk-scale synthesis and characterization of tin oxide nanowires by the molten salt synthetic method and the nanowire doping with antimony (n-types) and lithium. The work builds on the success of using n-doped SnO2 nanoparticles to selectively detect chlorine gas at room temperature. Replacing n-doped nanoparticles with n-doped nanowires reduces the number of inter-particle electron hops between sensing electrodes. The nanowire based sensors show unprecedented 5 ppb detectability of corrosive Cl2 gas concentration in air. At the higher range, 10 ppm of Cl2 gas leads to a 250 fold increase in the device resistance. During sensor recovery, FT-IR studies show that dichlorine monoxide (Cl2O) and chlorine dioxide (ClO2) are the desorbing species. Long term stability of devices is affected by lattice oxygen vacancies replaced by chlorine atoms. Bulk-scale synthesis of multiwall carbon nanotube (MWCNTs) was achieved by a novel inexpensive synthetic method. The green chemistry method uses the non-toxic and easy to handle solid carbon source naphthalene. The synthesis is carried out by simply heating naphthalene and organometallic precursors as catalysts in a sealed glass tube. Synthesis at 610º C leads to MWCNTs of 50 nm diameter and lengths exceeding well over microns. MWCNT doping is attempted with nitrogen (n-type) and boron (p-type) precursors. Palladium nanoparticles decorated on as-synthesized MWCNTs are employed for specific detection of explosive hydrogen gas with concentrations far below the explosive concentration limits. During performance, the sensor exhibits abnormal response behaviors at hydrogen gas concentrations higher than 1%. A model of charge carrier inversion, brought about by reduction of MWCNT by hydrogen molecules dissociated by Pd nanoparticles is proposed.

This thesis reports the study of electronic structures for single-walled carbon nanotubes, single layer graphene and thin graphite. A brief introduction is given in Chapter 1 for the geometric and electronic structures of the materials studied while a review for the theory and experimental results relevant to this thesis is given in Chapter 2. The effects of hydrostatic pressure on surfactant-wrapped-single walled carbon nanotubes are studied in Chapter 3 by using photoluminscence and photoluminscence excitation mapping. It is found that the changes to the optical properties can be explained by the compression in carbon-carbon bonds, an effective uniaxial strain exerted on the nanotubes and changes in the surrounding environment leading to changes in the many-body interactions experienced by the nanotubes. Chapter 4 reports the study of cross-polarized photoluminescence of nanotubes isolated by conjugated polymers dispersed in solvents. The effects of Coulomb interactions on the optical bandgaps of the nanotubes are discussed here. Chapter 5 reports Cyclotron resonances studies of graphene monolayers. It is found that a significant asymmetry exists between the electron and hole band structures near the Dirac point, and the asymmetry is bigger than that is expected in a simple tight-binding model. Chapter 6 reports a magnetoabsorption study of the electronic structures near the K- and H- points. It is found that the transitions are not describe well by the conventional Slonczewski-Weiss-McClure model, but can be described instead with a simplified asymmetric effective bilayer model.