none

The aim of master’s thesis was to develop a method for long-term measuring the influence of temperature on photovoltaic cells and lithium-polymer batteries and to design such measuring system. System was assembled on universal printed circuit board. It consisted of circuits for measuring temperature, illuminance and charging circuit, which charged battery with capacity 110 mAh. The PV cell BSK-SP9261 was used as source. Voltages was recorded by data acquisition device NI-USB 6009 and loged in program developed in LabVIEW 2012 enviroment. Afterwards, temperature, illuminance, voltage on PV cell and internal resistance of battery were computed.

The design processes for solar photovoltaic (PV) systems is improved to achieve higher reliability and reduced levelised cost of energy (LCOE) throughout this thesis. The design processes currently used in the development of PV systems are reviewed. This review process included embedding the author in a project to deliver four rooftop PV systems which totalled a megawatt of installed generating capacity, which at the time represented very significant system sizes. The processes used in this are analysed to identify improvement potential. Shortcomings are identified in three main areas: safety assurance, design process integration and financial optimisation. Better design process integration is required because data is not readily exchanged between the industry standard software tools. There is also a lack of clarity about how to optimise design decisions with respect to factors such as shading and cable size. Financial optimisation is identified as a challenge because current software tools facilitate optimising for maximum output or minimum cost, but do not readily optimise for minimum levelised cost of energy which is the primary objective in striving for grid parity. To achieve improved design process integration and financial optimisation, a new modelling framework with the working title SolaSIM is conceived to accurately model the performance of solar photovoltaic systems. This framework is developed for grid connected systems operating in the UK climate, but it could readily be adapted for other climates with appropriate weather data. This software development was conducted using an overarching systems engineering approach from design and architecture through to verification and validation. Within this SolaSIM framework, the impact of shading on array and inverter efficiency is identified as a significant area of uncertainty. A novel method for the calculation of shaded irradiance on each cell of an array with high computational efficiency is presented. The shading sub-model is validated against outdoor measurements with a modelling accuracy within one percent. Final verification of the over-arching SolaSIM framework found that it satisfied the requirements which were identified and actioned. The author installed the new CREST outdoor measurement system version 4 (COMS4). COMS4 is a calibrated system which measures 26 PV devices simultaneously. Validation of SolaSIM models against COMS4 found the modelling error to be within the 4% accuracy target except two sub-systems which had electronic faults. The model is validated against PV systems and found to be within the specified limits.

No description available.

As renewable energy plays an increasingly important role in the power system, the addition of PV systems to the distribution network has become a major trend in the current power system development. However, if a PV system with excessive capacity is added to the distribution network, voltage problems may occur in the system. Hence, it is important to determine the capacity of the PV system that can be added at the distribution system. The thesis aims to identify the major factors that affect the PV hosting capacity of distribution systems. The thesis studies various scenarios for the IEEE-123 test network PV system and evaluates the PV hosting capacity of the distribution system based on simulation tools including Matlab and Opendss software.

Distributed energy resources like solar power (PV Panels) are usually connected to the AC grid through a single phase voltage source inverter (VSI). The major drawback associated with single phase grid tie inverters is the double frequency component of the grid that appears on the DC bus link. Large electrolytic capacitors are generally employed in the inverters to eliminate the ripple component. However, their bulkiness and relatively short lifetime are motivational factors to replace them with small film capacitors. This paper presents a synchronous boost/buck based active power decoupling circuit in parallel with the dc-bus link capacitor and discusses the different types of control strategies implemented. Simulation results are presented for each control technique and it is shown that the ripple on the DC bus link is largely reduced due to inclusion of this circuit along with an expected extension of the lifetime due to the reduction in the amount of dc-bus capacitance used. / text

Due to the rapid growth of grid-tied solar photovoltaic (PV) systems in the generation mix, the distribution grid will face complex operational challenges. High PV penetration can create overvoltages and voltage fluctuations in the network, which are major concerns for the grid operator. Traditional voltage control devices like switched capacitor banks or line voltage regulators can alleviate slow-moving fluctuations, but these devices need to operate more frequently than usual when PV generation fluctuates due to fast cloud movements. Such frequent operations will impact the life expectancy of these voltage control devices. Advanced PV inverter functionalities enable solar PV systems to provide reliable grid support through controlled real injection and/or reactive power compensation. This dissertation proposes a voltage regulation technique to mitigate probable impacts of high PV penetrations on the distribution voltage profile using smart inverter functionalities. A droop-based reactive power compensation method with active power curtailment is proposed, which uses the local voltage regulation at the inverter end. This technique is further augmented with very short-term PV generation forecasts. A hybrid forecasting algorithm is proposed here which is based on measurement-dependent dynamic modeling of PV systems using the Kalman Filter theory. Physical modeling of the PV system is utilized by this forecasting algorithm. Because of the rise in distributed PV systems, modeling of geographic dispersion is also addressed under PV system modeling. The proposed voltage regulation method is coordinated with existing voltage regulator operations to reduce required number of tap-change operations. Control settings of the voltage regulators are adjusted to achieve minimal number of tap-change operations within a predefined time window. Finally, integration of energy storage is studied to highlight the value of the proposed voltage regulation technique vis-à-vis increased solar energy use. / Ph. D.

No description available.

Application of Photovoltaic PV panels for electricity production has rapidly increased in recent years in Sweden after launching a capital subsidy for PV panel installations in 2009. Kungsbacka municipality’s housing company equipped two groups of buildings in Fjärås with PV systems to generate electricity. The newly built residential buildings are connected to a DC-microgrid, whereas the existing buildings have been equipped with a single PV system. This project conducts a cradle to gate life cycle assessment (LCA) for this DC-microgrid energy system. The main purpose of this project is to determine which parts and processes of the DC-microgrid contribute to highest environmental impact throughout their lifespan from cradle to gate stages. Moreover, this study explores the energy payback time (EPBT) and the cumulative energy demand (CED) for the DC-microgrid. Additionally, this study performs two comparative LCA. First the DC-microgrid is being compared with PV system to determine which system has higher environment impacts, and secondly, the DC-microgrid is being compared with the average electricity mix in Sweden in terms of contribution to environmental impacts. The LCA follows the ISO 14040 framework and the baseline method is applied in order to assess 11 environmental impact categories. Two different functional units are adopted in this study. One is based on installed kilowatt peak (kWp) capacity by which environmental impacts of the PV system are compared with the DC-microgrid system. The other functional unit for this study is 1 kWh of delivered electricity to residential buildings produced by the DC-microgrid system. This functional unit is used exclusively for a stand-alone analysis of the DC-microgrid system in order to make it comparable with other microgrid systems or other systems with different energy sources, such as hydro, wind or nuclear. The results of the stand-alone LCA analysis of the DC-microgrid show that the battery has high contribution in human toxicity and terrestrial ecotoxicity whereas the energy hub system (Ehub) is the main contributor to eutrophication, abiotic depletion, fresh water aquatic ecotoxicity and marineaquatic ecotoxicity. The monocrystalline PV panel has the highest impact on global warming and abiotic depletion (fossil fuel). In addition, the EPBT for the DC-microgrid system is approximately 3.7 years. This means that one can get energy free of cost for an estimated time of 26.5 years if the lifetime of the system is assumed to be 30 years. The CED results show that monocrystalline PV production is an intense energy process which requires more non-renewable energy than all remaining parts of the DC-microgrid. The comparison of the DC-microgrid with the PV system reveals that the DC-microgrid has a higher environmental impact almost in all impact categories. This is mainly due to batteries and inverters which have a clear effect on the result. The CED analysis results illustrate that the multicrystalline PV panel production from the PV system is the most energy demanding process in both categories of renewable and non-renewable energy source. Moreover, the analysis illustrates that the DC-microgrid has still higher environmental impacts in all impact categories compared to the average electricity mix in Sweden. This is due to the electricity production in Sweden relies on hydropower and nuclear power with around 83 % of the total electricity production in the year 2017 which causes a lower environmental burden. Although the DC microgrid system shows a higher environmental impact compared to PV system, it is still a proper option to generate electricity since DC-microgrid system allows to achieve some indirect advantages such as energy saving due to an increase in own usage rate and self-sufficiency rate compared to the PV system. It should be noted that the end-of-life procedures becomes very important especially when crediting back for the recycling of materials. The collection and recycling of the PV panels at their end-of-life should be considered for future work as soon as reliable data are available. / Användningen av solpaneler har de senaste åren kommit att öka markant i Sverige. Ökningen beror på det statliga bidraget för installation av solceller som lanserades 2009. Kungsbacka kommun installerade solcellssystem i två olika typer av byggnader, ny och äldre befintlig byggnad. Den nya byggnaden anslöts till direkt mikronät (DC-mikcrogrid) och den äldre byggnaden utrustades med solcellssystem. Detta projekt utför en ’från vaggan till porten’ livscykelanalys (LCA) för energisystemet direkt mikronät. Syftet är i huvudsak att fastställa vilka delar och processer av det direkta mikronätet som bidrar till störst miljöpåverkan genom dess livslängd, det vill säga från vaggan till porten. Vidare undersöker studien återbetalningstiden (Energy PayBack Time, EPBT) och den ackumulerade energianvändningen (Cumulative Energy Demand, CED) för det direkta mikronätet. Studien utför två komparativa LCA varpå det direkta mikronätet först jämförs med solcellssystemet i syfte att fastställa vilket av systemen har större miljöpåverkan. Studien ämnar också jämföra det direkta mikronätet med den genomsnittliga energimixen i Sverige, också avseende miljöpåverkan. LCA metoden följer ISO 14040-ramverket. Studien är baserad på två funktionella enheter vilka består av installerad kilowatt peak (kWp) kapacitet vilken används för att jämföra solcellssystemet och det direkta mikromåttet. Den andra funktionella enheten är 1 kWh levererad elektricitet till bostäder som producerats genom det direkta mikronätet. Denna funktionella enhet används för en ’stand-alone’ analys av det direkta mikronätet i syfte att göra det jämförbart med andra mikrosystem eller system med olika energikällor så som vatten-, vind- och kärnkraft. Resultaten från ‘stand-alone’ livscykelanalysen av det direkta mikronätet visar på att batteriet har en större effekt på mänsklig toxicitet terrestrisk ekotoxicitet, varpå systemet för energihubb bidrar främst till övergödning, abiotisk utarmning, vattenlevande ekotoxicitet och havslevande ekotoxicitet. Monokristallin solpanel har större påverkan på global uppvärmning och övergödning (fossilabränslen). I övrigt är EPBT för det direkta mikronätet cirka 3,7 år vilket innebär att energin beräknas kostnadsfri i cirka 26,5 år, givet att det kan antas att systemets livslängd är 30 år. CED-resultat visar på att microkristallin solpanel är en intensiv energiprocess som kräver mer icke-förnybar energi jämfört med resterande delar av det direkta mikronätet. Jämförelsen mellan det direkta mikronätet och solcellssystemet visar på att det direkta mikronätet har större miljöpåverkan i de flesta kategorier. Detta beror i huvudsak på batterier och växelriktare som har tydlig effekt på resultatet. Av resultatet från CED-analysen framgår att produktion av multikristallin solpanel av solcellssystemet är det mest energikrävande processen i båda kategorierna för förnybar och icke-förnybar energikälla. Vidare framgår av analysen att det direkta mikronätet har en större miljöpåverkan i alla kategorier, jämfört med påverkan från genomsnittet av energimixen i Sverige. Detta beror på att elproduktionen i Sverige mestadels består av vatten- och kärnkraft som tillsammans 2017 utgjorde 83 procent av den totala energiproduktionen. Denna produktion orsakaren mindre miljöbelastning. Trots att det direkta mikronätet påvisar en högre miljöpåverkan än solcellssystemet, är det fortfarande ett alternativ till att generera elektricitet eftersom det direkta mikronätet bidrar till indirekta fördelar såsom energibesparing. Energibesparingen i det direkta mikronnätet sker således genom ökad användning av den egenproducerade energin samt självförsörjning. Det ska vidare tilläggas att ’end-of-life’ procedurerna blir viktiga i synnerhet när de återvunna materialet återanvänds. Vidare bör solpaneler återanvändas vid ’end-of-life’ vilket bör finnas i åtanke för vidarestudier och i samband med att data tillgängliggörs.

This thesis presents an investigation into a wide range of potential materials for organic photovoltaic (PV) devices. A variety of optical techniques are used to define physical parameters for each material such as the photoluminescence quantum yield (PLQY), absorption coefficient and exciton diffusion length. Electrical characterisation is used to determine the optimal structure for devices fabricated with these materials. A number of novel materials are presented in this thesis. These include new polymers, both soluble and precursor, and a relatively new class of material, the conjugated dendrimer. These are highly configurable branching molecular structures that enable fine tuning of material properties. Work on polymers presented in this thesis investigates how such materials can be improved by testing the effect of small changes to their molecular structure. One of these changes had significant effects upon the overall material characteristics. The introduction of a dipole across a polymer successfully created a charge separating material without the need for an extra species such as C60 to be present. The introduction of the conjugated dendrimer to PV applications allows significant scope for molecular engineering. Dendrimers enable tight control over certain aspects of the molecular properties. Small changes can be made such as colour tuning or solubility that enable optimisation to be performed on the molecular level, rather than on device structure. Such changes produced significantly higher internal quantum efficiencies (> 90%) than typical polymer devices and offer the prospect of power conversion efficiencies in excess of 10%. Time-resolved luminescence (TRL) spectroscopy was used to characterise the behaviour of photogenerated excitons within organic films. The investigation of exciton diffusion length was performed upon two polymers, each utilising two different time-resolved methods; diffusion to a quencher and exciton-exciton annihilation. It was found that diffusion in polythiophene films is anisotropic and the photoluminescence lifetime is dependent upon film thickness. This is explained by the formation of self-ordered microstructures during the spin coating process. Data modelling was performed which took into account both the thickness variation and the interaction of excitons with a quenching interface producing a much more realistic approach than previously published work.