abstract: With increased usage of green energy, the number of photovoltaic arrays used in power generation is increasing rapidly. Many of the arrays are located at remote locations where faults that occur within the array often go unnoticed and unattended for large periods of time. Technicians sent to rectify the faults have to spend a large amount of time determining the location of the fault manually. Automated monitoring systems are needed to obtain the information about the performance of the array and detect faults. Such systems must monitor the DC side of the array in addition to the AC side to identify non catastrophic faults. This thesis focuses on two of the requirements for DC side monitoring of an automated PV array monitoring system. The first part of the thesis quantifies the advantages of obtaining higher resolution data from a PV array on detection of faults. Data for the monitoring system can be gathered for the array as a whole or from additional places within the array such as individual modules and end of strings. The fault detection rate and the false positive rates are compared for array level, string level and module level PV data. Monte Carlo simulations are performed using PV array models developed in Simulink and MATLAB for fault and no fault cases. The second part describes a graphical user interface (GUI) that can be used to visualize the PV array for module level monitoring system information. A demonstration GUI is built in MATLAB using data obtained from a PV array test facility in Tempe, AZ. Visualizations are implemented to display information about the array as a whole or individual modules and locate faults in the array. / Dissertation/Thesis / M.S. Electrical Engineering 2012

M. Tech. (Department of Electronic Engineering, Faculty of Engineering and Technology) --Vaal University of Technology| / Global warming is of increasing concern due to several greenhouse gases. The combustion of fossil fuels is the major contributor to the greenhouse effect. To minimalise this effect, alternative energy sources have to be considered. Alternative energy sources should not only be environmentally friendly, but also renewable and/or sustainable. Two such alternative energy sources are hydrogen and solar energy. The regenerative fuel cell, commonly known as a hydrogen generator, is used to produce hydrogen. The current solar/hydrogen system at the Vaal University of Technology’s Telkom Centre of Excellence makes use of PV array to supply power to an inverter and the inverter is connected to the hydrogen generator. The inverter provides the hydrogen generator with 220VAC. The hydrogen generator has its own power supply unit to convert the AC power back to DC power. This reduces the efficiency of the system because there will be power loss when converting DC power to AC power and back to DC power. The hydrogen generator, however, could be powered directly from a PV array. However, the hydrogen generator needs specific input parameters in order to operate. Three different input voltages with their own current rating are required by the hydrogen generator to operate properly. Thus, a DC-DC power supply unit needs to be designed to be able to output these parameters to the hydrogen generator. It is also important to note that current PV panel efficiency is very low; therefore, the DC-DC power supply unit also needs to extract the maximum available power from the PV array. In order for the DC-DC power supply unit to be able to extract this maximum power, a maximum power point tracking algorithm needs to be implemented into the design. The DC-DC power supply is designed as a switch mode power supply unit. The reason for this is that the efficiency of a switch mode power supply is higher than that of a linear power supply. To reach the objective the following methodology was followed. The first part of the research provided an introduction to PV energy, charge controllers and hydrogen generators. The problem statement is included as well as the purpose of this research and how this research was to be carried out. The second part is the literature review. This includes the background study of algorithms implemented in MPPT’s; it also explains in detail how to design the MPPT DC-DC SMPS. The third part was divided into two sections. The first section is the design, programming and manufacturing of the MPPT DC-DC SMPS. The second section is the simulation of the system as a whole which is the simulation of the PV array connected to the MPPT DC-DC SMPS and the hydrogen generator. The fourth part in the research compared the results obtained in the simulation and practical setup. The last part of the research provided a conclusion along with recommendation made for further research. The simulation results showed that the system works with an efficiency of 40,84%. This is lower than expected but the design can be optimised to increase efficiency. The practical results showed the efficiency to be 38%. The reason for the lower efficiency is the simulation used ideal components and parameters, whereas the practical design has power losses due to the components not being ideal. The design of the DC-DC switch mode power supply, however, indicated that the hydrogen generator could be powered from a PV array without using an inverter, with great success.

Electrical energy is used at approximately the rate of 15 Terawatts world-wide. Generating this much energy has become a primary concern for all nations. There are many ways of generating energy among which the most commonly used are non-renewable and will extinct much sooner than expected. Very active research is going on both to increase the use of renewable energy sources and to use the available energy with more efficiency. Among these sources, solar energy is being considered as the most abundant and has received high attention. The mobile phone has become one of the basic needs of modern life, with almost every human being having one.Individually a mobile phone consumes little power but collectively this becomes very large. This consideration motivated the research undertaken in this masters thesis. The objective of this thesis is to design a model for solar power based charging circuits for mobile phone using Simulink(R). This thesis explains a design procedure of solar power based mobile charger circuit using Simulink(R) which includes the models for the photo-voltaic array, maximum power point tracker, pulse width modulator, DC-DC converter and a battery. The first part of the thesis concentrates on electron level behavior of a solar cell, its structure and its electrical model.The second part is to design an array of solar cells to generate the desired output. Finally, the third part is to design a DC-DC converter which can stabilize and provide the required input to the battery with the help of the maximum power point tracker and pulse width modulation. The obtained DC-DC converter is adjustable to meet the requirements of the battery. This design is aimed at charging a lithium ion battery with nominal voltage of 3.7 V, which can be taken as baseline to charge different types of batteries with different nominal voltages.

No description available.