The present diploma thesis concerns the research of plasmachemical reduction of copper corrosion layers. The process was based on using low pressure hydrogen RF plasma in which copper samples are treated for several hours. Four series of copper corrosion layers were prepared in four different corrosion atmospheres. The first two were prepared using saturated vapors of HCl and ammonium acetate that affected copper samples for one week. The second two sets were prepared by samples dipping in HNO3 and H2SO4. EDX analysis confirms visual composition of corrosion layers – chlorides, nitrides and sulphate, respectively. The ammonium acetate produced no corrosion layers and thus this set of samples was omitted. The optical emission spectroscopy was used to find out reactions in a hydrogen RF discharge. At the first, a character of plasma without samples was taken by measuring in continuous and pulsed regime. The integral spectrum intensity (300-700 nm) and intensities of hydrogen atomic lines were observed in the dependences on hydrogen flow, power and duty cycle. After that copper samples were treaded under various conditions in continual and pulse regime, typically at pressure of 170 Pa, 200 W power and hydrogen flow rate of 10.2 ml/min. The integral OH radical spectral intensity in the range of 305 – 330 nm was used as a monitor of plasma treatment process. The experimental results showed that intensities of OH radical depended strongly on the corrosion layer kind as well as on the RF discharge mode. Reduction of corrosion layers treated in the pulsed regime was not so satisfactory then in the continuous regime probably due to lower temperature of sample during the treatment. The total supplied energy into the system was also lower in this case. The sample sputtering was observed during the reduction in continuous regime. It means the corrosion was successfully removed but the process was not stopped at that moment, so it is necessary to propose another additional monitoring process besides observing OH radicals. Our experimental results are the first step in the spread research of plasmachemical treatment of copper made archaeological artifacts.

This diploma thesis is focused to the plasma chemical reduction of model corrosion layers prepared on bronze samples. Bronze was the main material for production of the subjects in Bronze Age. First, it was very rare, and therefore was used only for making jewellery and other decorative subjects. Later, the objects of daily use and weapons were produced of bronze. These objects are found and it is necessary to restore him and preserve the cultural heritage for future generations. The research and the optimalization of plasmochemical reduction of model corrosion layers on bronze samples contributes to this. A metallographic grinder was used to create a defined surface, first with the sandpaper P 280 and then after sample 90 degree rotation with the sandpaper P 600. This ensured uniform surface at all bronze samples that is necessary to provide the same corrosion conditions. The grinded samples were washed by ethanol and dried by hot air stream. To prevent contact with the surrounding atmosphere and successive initiation of corrosion, the samples were stored in lockable polyethylene bags. This step was followed by the preparation of model corrosion layers. Hydrochloric and sulfuric acids were chosen as corrosive environments. Petri dish containing 20 ml of the selected acid was placed at the bottom of the desiccator. Samples were placed to the ceramic grate, over the dish, and they were corroded (in vapours of hydrochloric acid for 34 days and in vapours of sulfuric acid for 27 days). The corroded samples were treated using low-pressure hydrogen plasma excited by RF generator. Treatment of samples was carried out in quartz cylindrical reactor (length of 90 cm, inner diameter 9.5 cm) with copper electrodes placed outside. The pressure in the reactor was ranged around 160 Pa at hydrogen flow rate of 50 sccm during the experiments. The continuous and pulse modes (duty cycle of 25%, 50% or 75%) at peak power of 50–300 watts were used for the treatment of 90 minutes duration. The plasma treatment was monitored by optical emission spectroscopy of OH radical using compact Ocean Optics HR4000 spectrometer. Its integral intensity is proportional to the corrosion layer removal. The rotational temperatures of plasma were calculated using selected OH rotational lines, too. The sample temperature during the treatment was measured by thermocouple installed inside the additional non-corroded samples. The reduction of corrosion layer is successful when the maximum of relative intensity of OH radicals is produced and follow gradual decline. The samples which corroded in vapours of sulphuric acid and were treated in pulse modes with duty cycle of 25 % or with delivered power of 50 W has produced no maximum. To the remain samples the maximum although were observed, but reduced corrosion products on the surface were very cohesive. The maximum of relative intensity of OH radicals was observed at all samples corroded in vapours of hydrochloric acid. But there is problem with temperature of sample during experiment. The samples which layer of corrosion product was after experiment incoherent produced the layer of deposit tin. This effect formation at a higher temperature of sample during experiment and therefore with greater deliver energy.

This master´s thesis dealing with study of influence of inert atmosphere on the wettability of soldered surfaces. The theoretical part is discussed the issue of the soldering, solder joint, oxidation, and inert atmosphere. The glass cover with internal inert gas preheating for the wetting balance testing was prepared in the practical part. With this adjustment were realised tests, in which was examined the effect of the inert gases on the wettability of different materials combination. Further experiments were focused on plasma surface cleaning as possible flux substitution. The evaluation of these experiments were discussed in the end of this master´s thesis. Some of topics were designed for further experiments.

VACULA Jakub: Optimization of plasma cutting parameters Diploma thesis of the attendance engineer´s study – Mechanical Engineering, specialization Machinery Technology. Academic year 2008/2009. Faculty of Mechanical Engineering of University of Technology in Brno, Institute of the Manufacturing Technology. The Diploma thesis is concerned with the thermal division of a material, concretely by the plasma cutting. It monitors the operational parameters influence of this process to the result quality of cut and the purpose is to optimize these parameters from the qualitative standpoint. The experiment was executed at the plasma cutting equipment Fine Focus 800 of the company KJELLBERG with the utilization of the material S 690 QL. On the base of the literary study of the thermal division of the materials problems it was also described the comparison of the plasma cutting with the method of the division of materials by the oxygen, both from the point of view of the quality, and from the economical point of view.

FŇUKALOVÁ VERONIKA: Comparison of MAG and plasma welding. My master´s thesis describes questions of welding of high-firmed and high-abrasion resistant steels with welding processes MAG (Metal Active Gas) and plasma. The weldability of CREUSABRO 8000 steel was passed judgement on, based on literary study of high-abrasion resistant steel question. The technology, characteristics of welding, kind of additional material were proposed. Tensile tests, brittleness tests for determination of strength characteristics and hardness tests of welding joints were implemented and analyzed experimentally. Further were analyzed macrostructure and microstructure. Other alternatives of high-firmed and abrasion resistant steels are part of my master’s thesis.

Master's thesis, elaborated within Master's degree, submits a proposal of suitable technology for manufacturing “column foot“ part, which attaches filtration unit to the ground. Material is 6 mm thick sheet steel in accordance with ČSN 41 1375 norm. Run (/production batch) of the part is 4 000 pieces per year. On the basis of literary study about unconventional technologies for flat sheet metal production 3 technologies were suggested: plasma cutting, water jet cutting and laser cutting. These technologies were technologically and economically analyzed. At the end thesis evaluates whether purchase of respective machine would pay out for the firm or they should continue to buy parts from cooperation company.

The substance of present work is to provide standard thermodynamic functions (STF) of small size molecules for the calculation of the composition and thermodynamic properties of low-temperature plasma, and also method for such a calculation applying obtained STF under non-ideal plasma conditions. With a view to further application in modelling the phenomena in thermal plasma the range of pressures is limited to the region from 0.01 bar to 100 bar, and that of temperature to 298.15–50 kK. To obtain STF the method of partition function resulting from statistical mechanics was proposed. State of art in the given scientific area and theoretical basis of the statistical mechanics required for establishing of the proposed method together with discussion of partition function divergence problem have been reviewed. For the calculation of STF of diatomic molecules the method of direct summation has been employed, whereas, as for the larger size molecules, the rigid rotor and harmonic oscillator model have been generally adopted. The spectral data required for the calculations have been taken from literature, or, in selected cases, these have been computed by quantum chemistry ab initio techniques. The resulting STF have been included into already existing database system of thermodynamic properties and those can serve as input data for subsequent thermodynamic calculations. A general method has been worked out for the purpose of the computation of thermodynamic properties and composition of non-ideal homogenous plasma system in thermodynamic equilibrium. The method is based on minimizing total Gibbs energy to compute at constant pressure or Helmholtz energy to compute at constant volume. The computation algorithm was implemented into computer program and subsequently applied to the computation of the composition and thermodynamic properties of SF6 dissociation and ionization products using obtained STF.

Thesis deals with the analysis of vitamin E in cereal samples, namely barley and wheat and malt produced from them. Selected samples were treated with low-temperature plasma, fungicide and biological treatment to elimination fungus and mycotoxins. The aim of the thesis was to find out the influence of the treatment, the combination of several types of treatment on vitamin E content in grain and malt. If the content of health-positive substances is not reduced and grain can be used for food, malt, or for feed purposes. The theoretical part focuses on the properties, occurrence, biochemistry and importance of vitamin E for living organisms. It also focuses on the properties of cereals that are a significant source of vitamin E. Malt production and sample treatment are also described. The experimental part describes the field experiment, individual types of treatment, extraction of vitamin E from the samples and determination of vitamin E content by high performance liquid chromatography with fluorescence detection. The results are compared with the current literature. It was found that the treatment did not have a significant negative effect on vitamin E content.

This diploma thesis deals with the synthesis of an organosilica polymer which could be used as a binder for titanium dioxide photocatalytic layers. The main reason for incorporating the binder into the photocatalytic layers is not only the improving of the mechanical properties, but above all, the binder could help with production of low-temperature photocatalytic layers, that could be applied to heat-sensitive materials such as plastic materials. This could create layers on flexible materials that could be easily made into any shape. The work focuses on the synthesis of organosilica polymer from the organosilica precursor and subsequent characterization of the binder. Surface tension, viscosity, density, XRD, thermal analysis of silica binder solutions was performed. Titanium dioxide compositions with this binder were prepared, then they were printed and the layers were treated with UV and plasma. Treated layers were examined by FT-IR and a voltamperometric characterization was performed.

This master thesis deals with determination of temperature field in a real circuit breaker. This issue is solved by analysis of measured emission spectra at selected points of the circuit breaker. Spectral line ratios and Boltzmann plot are used for calculation of temperature. These methods are based on elemental analysis of plasma. The main result is finding significant changing of chemical composition of plasma beyond determination of temperature field.