The aqueous suspension prepregging technique was used to fabricate PEEK and PPS matrix composites with polyimide interphases of tailored properties. The structure-property relationships of Ultem-type polyimide and BisP-BTDA polyimide which were made from various water soluble polyamic acid salts were studied. The molecular weight of the polyimides was shown to be dependant upon the selection of the base used for making the polyamic acid salt. The development of an Ultem-type polyimide with controlled molecular weight and properties similar to commercial Ultem 1000 was accomplished with the Ultem-type TPA+ polyamic acid salt. Both the Ultem-type polyimides and the BisP-BTDA polyimides derived from the NH4+ salt and the TMA+ salt were shown to crosslink at elevated temperatures. Blends of Ultem-type polyimide with PEEK and BisP-BTDA polyimide with PEEK were prepared to study the structure-property relationships of model composite matrices. Since both polyimides are miscible with PEEK, interdiffusion of the polyimides with PEEK is expected, however, the interdiffusion behavior is complicated by the crosslinking mechanism of the polyimides. Ultem-type polyimide interphase, PEEK matrix composites and BisP-BTDA polyimide interphase, PEEK matrix composites were fabricated using the aqueous suspension prepregging technique and evaluated to determine the effects of the interphase properties on the bulk composite performance and durability. Three different Ultem-type polyimides from the NH4+, TMA+ and TPA+ polyamic acid salts were used and two different BisP-BTDA polyimides from the NH4+ and TMA+ polyamic acid salts were used. The transverse flexure strength was used to qualitatively rank the composites by level of interfacial shear strength. The longitudinal tensile strength of the composites was shown to vary with relative interfacial shear strength. The trend of these data qualitatively support the existence of a maximum longitudinal tensile strength at an optimum interfacial shear strength. Notched fatigue testing of the Ultem-type polyimide interphase, PEEK matrix composites showed that the initial split growth rate increased with decreasing relative interfacial shear strength. Ultem-type polyimide interphase, PPS matrix composites were fabricated using the aqueous suspension prepregging technique and evaluated to determine the effects of the interphase properties on the bulk composite performance. Three different Ultem-type polyimides from the NH4+, TMA+ and TPA+ polyamic acid salts were used. The transverse flexure strength was used to qualitatively rank the composites by level of interfacial shear strength. The longitudinal tensile strength of the composites was shown to vary with relative interfacial shear strength. The trend of these data qualitatively support the existence of a maximum longitudinal tensile strength at an optimum interfacial shear strength. / Ph. D.

>Magister Scientiae - MSc / Microfluidic paper based electrochemical sensing devices (μPEDs) provides a new way for point of care testing (POCT). μPEDs offer an inexpensive, portable, easy to use technology too monitor the environment and diagnose diseases, especially in developing countries in cases where there is not enough infrastructure and a limited trained medical and health professionals. The aim of this work is to develop a paper based electrode which can be further integrated into a microfluidic paper device to develop miniature point of care devices. Paper was used as a substrate for printing of the electrode because it is found everywhere, inexpensive and it is compatible with a number of chemical, biochemical and medical applications. Polyamic acid (PAA) was incorporated into commercial carbon ink and was used to print the working electrode. The first part of the study was conducted using the commercial screen printed carbon electrodes (SPCE) to study and understand the electrochemical behaviour of PAA. Cobalt nanoparticles and cobalt nanoparticles‐polyamic acid composites were electrochemically deposited onto SPCE. The modified electrodes were characterised using cyclic voltammetry. As synthesised polyamic acid were characterised using Scanning Electron Microscopy (SEM) to evaluate the morphology and chemical composition of polyamic acid. Transmission Electron Microscopy (TEM) was used to study the particle size and chemical composition of cobalt nanoparticles. Fourier Transform Infrared Spectroscopy (FTIR) was used to study the chemical nature of polyamic acid and cyclic voltammetry (CV) was used to study the electrochemical behaviour of polyamic acid and cobalt nanoparticle electrodes. The diffusion coefficients and formal potential of the electrodes were calculated. The modified and bare electrodes were also used to electrochemically detect Norfloxacin in an aqueous solution by CV and square wave voltammetry (SWV) and the analytical performance of the electrochemical systems are reported here. The obtained limit of detection for the bare SPCE was 3.7 x 10‐3 M and 14.7 x 10‐3 M for the PAA‐SPCE.

Philosophiae Doctor - PhD / Polyamic acid (PAA) nanostructured materials were successfully produced by electrochemical deposition and electrospinning using polyvinlypyrrolidone (PVP) as supporting polymer. Polyamic acid thin film and nanofibers were deposited directly at the surface of a screen-printed carbon electrode (SPCE) as electro-catalysts for reliable analytical reporting of sulphonamide as contaminants of emerging concern by electrochemical techniques. Fourier transform infrared (FTIR) spectroscopy was used to confirm the structural integrity of the PAA electrospun nanofibers compared to the chemical synthesized PAA. Brunauer-Emmett-Teller (BET) was used to determine the surface area of the nanofibers. The surface morphology and surface thickness of the polyamic acid (PAA) nanofibers on the screen-printed electrodes was studied using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Cyclic voltammetry (CV) was used to study redox behavior of the nanostructured PAA modified screen-printed carbon electrodes. Electrochemical parameters surface concentration, diffusion coefficient, formal potential and peak separation were determined. Three sulphonamides were selected based on the United States of protection agency (US EPA) and World Health Organization (WHO) list of emerging contaminants and detected sulphonamides in environmental waters in South Africa and other African regions. The selected sulfonamides were evaluated at the unmodified and modified screen-printed carbon electrodes. The sulphonamides were evaluated in three different supporting electrolytes at pH < 7 and >7 to enhance electrochemical signal reporting. Sulfadiazine (SDZ), sulfamethoxazole (SMX) and sulfamethazine (SMZ) displayed peaks at 0.80 V vs Ag/AgCl in 0.1 M tris-HCl using square wave voltammetry at the unmodified transducer. At the PAA thin film transducer, SDZ, SMX and SMZ displayed well-defined analytical oxidative peaks at 0.77 V 0.82 V and 0.83 V vs Ag/AgCl respectively. The LOD (n=3) for SDZ was found to be 12.14 ųM with a correlation coefficient of 0.9950. The LOD (n=3) for SMX and SMZ was found to 14.59 ųM (R2 =0.9928) and 10.41 ųM (R2 =0.9963). These sulphonamides were also electro-analytical evaluated at the screen-printed carbon PAA nanofiber modified transducer. SDZ, SMX and SMZ produced well-defined analytical signals at 0.79 V, 0.81 V and 0.78 V vs Ag/AgCl respectively. The determined LOD (n=3) for the individual sulphonamides was 8.26 ųM, 16.59 ųM and 8.81 ųM SDZ, SMX and SMZ respectively. The linearity correlation coefficient (R2) was determined to be 0.9977, 0.9956 and 0.9974 respectively. The efficacy of the proposed nanostructured PAA thin film modified screen-printed carbon sensor was evaluated by performing recovery studies for the selected sulphonamides using square wave voltammetry. Tap water was used to simulate environmental matrix. The recoveries of SDZ with respect to each concentration were 98.84% (RSD 4.98%) to 40.58% (RSD 6.74%). For SMX the recoveries were 154.17% (RSD 11.00%) to 111.03% (RSD 16.80%). The recoveries for SMZ with respect to each concentration were 184% (RSD 8.19%) to 90.26 (RSD 18.26%) indicating the reliability of the analytical results. / 2021-09-01

When the inorganic domain sizes in a composite are reduced to a level such that a "molecular composite" is formed, the hybrid materials are commonly referred to as "ceramers". Hybrid materials span from inorganically modified organic polymers to inorganic g1asses slightly modified by organic polymers. The incorporation of an inorganic phase into an organic polymer is done almost exclusively by the "sol-gel" process.

>Magister Scientiae - MSc / Pollution of water sources, aquifers and wetland systems caused by industry, agriculture, and municipally treated wastewater is a worldwide problem that contributes to the scarcity of clean and potable water. Rivers, channels, lakes, oceans, and ground water are often contaminated by a variety of organic substances that can affect aquatic life and threaten human health. Organic compounds such as antibiotics that are not effectively removed by modern day water treatment technology are a growing threat to water quality and health. The emergence of antibiotics in the environment particularly aquatics have become a matter of concern as they may result in induction and spread of bacterial resistance which may be harmful to humans or animals. After administration, antibiotics for human use or their metabolites are excreted into the effluent and reach the sewage treatment plant (STP). Not all Antibiotics in sewage treatment plants are eliminated. Consequently they can pass through the sewage system and may end up in environmental and even potable water systems. Antibiotic residues have been reportedly found in places such as hospital wastewaters, wastewater treatment plants and surface waters all over the world with concentrations ranging from approximately 60-120000 ng/, 2-580 ng/L and 5-1300 ng/L respectively. The current methods that are used to detect antibiotics can be quite expensive and time consuming due to sample preparation (necessary for detection of very low concentrations of antibiotics in water) and technology used in the instruments. Electrochemical sensors and biosensors are simple systems, with high selectivity and sensitivity for individual measurements and cost effectiveness. The development of composites based on conductive phases dispersed in polymeric matrices has led to important advances in analytical electrochemistry. Polyamic acid and graphene oxide are both materials with well-defined electrochemistry and are easily processable in the design of various sensor formats. In this study we present a novel polyamic acid - graphene oxide (PAA/GO) electrode which was prepared for electrochemical screening of antibiotic residues in aqueous systems. Polyamic acid (PAA) and graphene oxide (GO) were successfully synthesized independently and characterized using SEM which was used to study the morphology of the PAA, FTIR spectroscopy to confirm chemical structures and functional groups as well as CV and SWV which were used to identify the unique electrochemical behavior of PAA and GO respectively. Polyamic acid-graphene oxide nanocomposite was prepared and characterized by CV, SWV, FTIR and SEM. The novel electrode (PAA/GO/SPCE) was prepared by electrochemically depositing PAA/GO (0.03 mg/mL) onto SPCE electrodes using 5 cycles between −1000 mV and 1000 mV at 50 mVs. The analytical performance of the electrochemical sensor towards detection of neomyxin and norlfoxacin was compared to standard Uv-vis spectroscopy method. The Uv-vis spectroscopy showed LOD of 1.61x10-5 M and 1.41x10-5 M for norfloxacin and neomycin respectively. The PAA/GO electrochemical sensor had a LOD of 3.37x10-7 M for norfloxacin and 1.066x10-6 M for neomycin. Sensitivity of the UV/vis method was comparable to electrochemical sensor sensitivity for neomycin and norfloxacin.

Philosophiae Doctor - PhD / Polyamic acid-polypyrrole (PAA/PPy) composite films were prepared and characterised for the use as conducting platforms in the design of biosensor systems. The thin films were synthesised by electrochemical method from a solution containing controlled molar ratio of chemically synthesised polyamic acid (PAA) and pyrrole monomer. Homogenous films were obtained incorporating PAA into electropolymerised polypyrrole (PPy) thin film. The concentration of PAA (1.37 × 10-6 M) was kept fixed throughout the composite ratio analysis, whilst the concentration of PPy was varied from 1.9 × 10-3 M to 9.9 × 10-3 M. The PAA/PPy thin films were electrodeposited at a glassy carbon electrode (GCE) and characterised using Fourier Transform Infrared Spectroscopy (FTIR), Raman spectroscopy, Atomic Force microscopy (AFM), Scanning electron microscopy (SEM) and electrochemical (CV, SWV) techniques. The composition that best represented the homogenous incorporation of PAA into PPy matrix was observed at a PAA/PPy ratio of 1: 4.13 × 10-3. This composite was observed to have two sets of coupled peaks with formal potential 99 mV and 567 mV respectively. The De determined from cyclic voltammetry using the anodic peak currents were found to be twice as high (5.82 × 10-4 cm2/s) as the De calculated using the cathodic peak currents (2.60 × 10-4 cm2/s), indicating that the composite favours anodic electron mobility. Surface morphology and spectroscopy data support the formation of a homogenous polymer blend at the synthesis ratio represented by composite 3. For the construction of a biosensor the spectroscopic and electrochemical properties of the enzyme, luciferase and the analytes i.e naphthalene and fluoranthene were evaluated. Fluorescence spectroscopy studies were carried out to characterize the enzyme’s bioluminescence response in PBS at pH 7. Luciferase showed an absorption peak at 340 nm. The bioluminescence properties of the enzyme with the analytes were explored by fluorescence spectroscopy. The emmision peak at 340 nm gradually decreased as the concentration of each analyte was increased respectively.

Magister Scientiae - MSc (Chemistry) / Blending polymers together offers researchers the ability to create novel materials that have a combination of desired properties of the individual polymers for a variety of functions as well as improving specific properties. The behaviour of the resulting blended polymer or blend is determined by the interactions between the two polymers. The resultant synergy from blending an intrinsically conducting polymer like polyaniline (PANI), is that it possesses the electrical, electronic, magnetic and optical properties of a metal while retaining the poor mechanical properties, solubility and processibility commonly associated with a conventional polymer. Aromatic polyamic acid has outstanding thermal, mechanical, electrical, and solvent resistance properties that can overcome the poor mechanical properties and instability of the conventional conducting polymers, such as polyaniline.

Philosophiae Doctor - PhD (Chemistry) / Tuberculosis (TB) is an airborne disease caused by Mycobacterium tuberculosis (MTB) that usually affects the lungs leading to severe coughing, fever and chest pains. It was estimated that over 9.6 million people worldwide developed TB and 1.5 million died from the infectious disease of which 12 % were co-infected with human immunodeficiency virus (HIV) in the year 2015. In 2016 the statistics increased to a total of 1.7 million people reportedly died from TB with an estimated 10.4 million new cases of TB diagnosed worldwide. The development of the efficient point-of-care systems that are ultra-sensitive, cheap and readily available is essential in order to address and control the spread of the tuberculosis (TB) disease and multidrugresistant tuberculosis.

Magister Scientiae - MSc / The toxicity of microcystin is associated with the inhibition of serine/threonine protein phosphatases 1 and 2A, which can lead to hepatocyte necrosis and haemorrhage. Analysis of microcystin is most commonly carried out using reversed-phase high performance liquid chromatographic methods (HPLC) combined with ultra-violet (UV) detection .The ability of these techniques to identify unknown microcystin in environmental samples is also restricted by the lack of standard reference materials for the toxins. Highly specific recognition molecules such as antibodies and molecularly imprinted polymers (MIPs) have been employed in the pre-concentration of trace levels of microcystin from water and show great potential for the clean-up of complex samples for subsequent analysis. New biosensor technologies are also becoming available, with sufficient sensitivity and specificity to enable rapid ‗on-site‘ screening without the need for sample processing. In this work we constructed a Protein phosphatase biosensor for detection of microcystin-LR in aqueous medium, onto polyamic acid/graphene oxide (PAA: GO) composite electrochemically synthesised in our laboratory. The composites were synthesised at three different ratios i.e. 50:50, 80:20 and 20:80 to evaluate the effect of each component in the search to produce highly conductive mediator platforms. The electrochemistries of the three different composites were evaluated using CV and SWV to study interfacial kinetics of the materials as thin films at the glassy carbon electrode. The phosphatase biosensor parameters were evaluated using CV, SWV, EIS and Uv-vis spectroscopy. The affinity binding of the microcystin-LR to protein phosphatase 2A was investigated using electrochemical impedance spectroscopy which is a highly sensitive method for measuring interfacial kinetics of biosensor systems.