Master of Science / Department of Industrial and Manufacturing Systems Engineering / Shing I. Chang / This research studies a few methodologies for real-time detection of wave profile changes. In regular profile monitoring, change detection takes place at the end of time period when a complete profile is available. In real-time change detection of profiles, a potential profile change takes place between the beginning and the end of the time period. The decision involves the identification whether a process is in control or out of control before the entire profile is generated. In this regard, five proposed methodologies were developed and tested in this thesis. Earthquake waves, manufacturing processes, and heart beat rate are a few examples of profiles with different natures that the proposed methodologies can be applied to. Water temperature profiles generated during a curing process are considered as an example in this study. Successful implementation of the proposed work on these profiles would cause saving great amounts of time and money. Five methods are studied for monitoring the water control process of a curing process. The first four proposed methodologies are based on an univariate approach where the statistic used for process monitoring is the enclosed area between the profiles and their fitted cutting lines. A multivariate approach is also proposed. A simulation study is also conducted when the best method is chosen based on it performance and simplicity of operations. Various types of acceptable and unacceptable profiles are simulated for the best proposed method identified in the preliminary study. The best method has a satisfactory performance in detecting the changes in the unacceptable profiles. In addition, the false alarm rate in identifying acceptable profiles as bad profiles is lower than 10%.

Introduction Measuring the beam profile on a medical cyclo-tron in real time can aid in improved tuning of the cyclotron and give important information for a smooth operation. Typically the beam profile is measured by an autoradiography technique or even by a scintillator that can be viewed in real time [1, 2]. Another method is to use collimators in front of the target to assess the beam center-ing [3]. All these methods have potential draw-backs including; an inability to monitor the beam in real time for the radiograph, exhibiting a non-linear correlation in signal response to the power deposited for a scintillator, and not providing a 2-dimensional profile of the complete beam for collimators. Our goal was to design a realtime, linear, 2-dimensional beam-profile monitor that is able to withstand the high power of a PET cyclotron. Material and Methods The beam-profile monitor (PM) is designed for the TR13, a 13MeV negative hydrogen-ion cyclotron at TRIUMF. The design follows the concept of a ‘harp’ monitor, widely used at TRIUMF for tuning proton and radioactive ion beams, and is installed on the extraction port without separation from the tank vacuum. The TR13 monitor is designed to withstand a 13 MeV proton beam with a beam current of up to 25 µA, has an active area of 10 by 10 mm and does not affect the 10-7 torr tank vacuum. The device consists of a water-cooled Faraday cup made out of aluminium for low activation and two orthogonal rows of eight tungsten electrodes each mounted on a water-cooled support frame. Electrodes are spaced 1 mm apart from each other, see FIG. 1. The electrodes are electrically isolated from each other and each has a current pickup soldered to it. The material and the shape of the electrodes are optimized to withstand the deposited power of the proton beam. A voltage of -90 V is applied to the electrodes to repel secondary electrons and prevent crosstalk between neighbouring electrodes. The electrode current is amplified using a custom current amplifier, and read by an ADC. From there, the current data is displayed on a PC. This allows one to observe changes of the beam profile in real time. The electronics are designed to read out all sixteen channels in parallel, or, if only a limited number of ADC channels are available, to cycle through the different channels. In our current setup all sixteen channels are read out simultaneously. Results and Conclusion The beam-profile monitor provides a real-time representation of the proton beam, see FIG. 2. The data can also be recorded and analyzed at a later time. The linearity of the monitor has been measured up to 30 µA of proton beam current [4]. With the use of the monitor, it was possible to increase the output of the ion source into the target by 50% in comparison to the standard tune.

A megawatt class electron linear accelerator (e-linac) will be constructed at TRIUMF as part of the new ARIEL facility which will produce rare ion beams for the study of nuclear structure and astrophysics, and material science. The 50MeV, 10mA, continuous wave e-linac will drive gamma ray induced fissioning of a Uranium target for the production of neutron rich beam species. View Screens located at a number of places along the e-linac beam-line will acquire two dimensional images of the transverse electron beam profiles, providing measurements of the size, position, and shape of the incident e-linac beam. The design of the View Screens will be presented, based on design studies and simulations performed to evaluate the performance of the View Screens under various operating conditions. These studies include GEANT simulations of the energy loss and scattering of the electron beam as it passes through the scintillation and Optical Transition Radiation beam targets, the subsequent thermal response of the targets, and a ray tracing optics simulation to optimize the configuration of the imaging optics. Bench test have been performed on the resulting optics design to evaluate the imaging characteristics, verifying fulfillment of the design requirements. Construction of a prototype View Screen device is currently underway, with beam tests scheduled for Fall 2011. A total of 14 View Screens will be constructed and installed along the e-linac beam-line. / Graduate

The TRIUMF view screen system encompases a set of devices which individually image, and produce measurements of, the transverse profile of an accelerated electron beam. A control system is an essential component of the overall diagnostic device. The system requirements were compiled from those produced by the TRIUMF laboratory and from those based on the needs of the individual diagnostic devices. Based on the requirements, a control system was designed and implemented with a combination of industrial electrical and mechanical hardware, and a variety of software components. One component of the image reconstruction algorithm was validated with experimental data; the accuracy and precision of beam profile measurements was evaluated through simulation studies. Although it was not possible to demonstrate the satisfaction of requirements relating to alignment, it was shown that all other requirements were satisfied. / Graduate / 0798 / 0752 / 0605

Introduction Measuring the beam profile on a medical cyclo-tron in real time can aid in improved tuning of the cyclotron and give important information for a smooth operation. Typically the beam profile is measured by an autoradiography technique or even by a scintillator that can be viewed in real time [1, 2]. Another method is to use collimators in front of the target to assess the beam center-ing [3]. All these methods have potential draw-backs including; an inability to monitor the beam in real time for the radiograph, exhibiting a non-linear correlation in signal response to the power deposited for a scintillator, and not providing a 2-dimensional profile of the complete beam for collimators. Our goal was to design a realtime, linear, 2-dimensional beam-profile monitor that is able to withstand the high power of a PET cyclotron. Material and Methods The beam-profile monitor (PM) is designed for the TR13, a 13MeV negative hydrogen-ion cyclotron at TRIUMF. The design follows the concept of a ‘harp’ monitor, widely used at TRIUMF for tuning proton and radioactive ion beams, and is installed on the extraction port without separation from the tank vacuum. The TR13 monitor is designed to withstand a 13 MeV proton beam with a beam current of up to 25 µA, has an active area of 10 by 10 mm and does not affect the 10-7 torr tank vacuum. The device consists of a water-cooled Faraday cup made out of aluminium for low activation and two orthogonal rows of eight tungsten electrodes each mounted on a water-cooled support frame. Electrodes are spaced 1 mm apart from each other, see FIG. 1. The electrodes are electrically isolated from each other and each has a current pickup soldered to it. The material and the shape of the electrodes are optimized to withstand the deposited power of the proton beam. A voltage of -90 V is applied to the electrodes to repel secondary electrons and prevent crosstalk between neighbouring electrodes. The electrode current is amplified using a custom current amplifier, and read by an ADC. From there, the current data is displayed on a PC. This allows one to observe changes of the beam profile in real time. The electronics are designed to read out all sixteen channels in parallel, or, if only a limited number of ADC channels are available, to cycle through the different channels. In our current setup all sixteen channels are read out simultaneously. Results and Conclusion The beam-profile monitor provides a real-time representation of the proton beam, see FIG. 2. The data can also be recorded and analyzed at a later time. The linearity of the monitor has been measured up to 30 µA of proton beam current [4]. With the use of the monitor, it was possible to increase the output of the ion source into the target by 50% in comparison to the standard tune.

Beam profile monitors provide position and ux distribution information to facilitate the configuration of an experimental apparatus and are an important component of any accelerator facilities beam diagnostic system. Nuclear physics experiments typically involve the incidence of high energy particles or gamma-rays on some target material and the detection of the products of the ensuing interactions. Therefore, knowing the profile of the incident radiation beam is desirable. To address the need for a profile monitor for the High-Intensity Gamma-Ray Source, development of a CCD-based gamma-ray beam profiler was undertaken. The profiler consisted of plastic scintillator, a lens system and a Starlight Express MX5 CCD camera, all contained within a light tight box. The scintillation pattern, created by the interaction between the incident gamma-rays and the scintillator, could be focused onto the CCD. Simulations were used to determine the amount of power that would be absorbed for different beam energies and scintillator thicknesses. The use of a converter material, placed directly against the scintillator to improve power deposition, was also investigated. The system was tested in order to and the camera noise characteristics, the optical resolution and magnification and the systems responsivity to power absorption in the scintillator. Using a 137Cs source, preliminary beam proles were obtained. By combining the results of the testing and simulation, predictions of the required length of exposure were made. It was determined that a beam with a flux of 10^6/s and a diameter of 2.5 cm could be profiled, using 6.0 mm of plastic scintillator and 0.6 mm of iron converter, to within 5% error per 0.64 mm x 0.91 mm resolving unit, in less than 1 minute.

Beam profile monitors provide position and ux distribution information to facilitate the configuration of an experimental apparatus and are an important component of any accelerator facilities beam diagnostic system. Nuclear physics experiments typically involve the incidence of high energy particles or gamma-rays on some target material and the detection of the products of the ensuing interactions. Therefore, knowing the profile of the incident radiation beam is desirable. To address the need for a profile monitor for the High-Intensity Gamma-Ray Source, development of a CCD-based gamma-ray beam profiler was undertaken. The profiler consisted of plastic scintillator, a lens system and a Starlight Express MX5 CCD camera, all contained within a light tight box. The scintillation pattern, created by the interaction between the incident gamma-rays and the scintillator, could be focused onto the CCD. Simulations were used to determine the amount of power that would be absorbed for different beam energies and scintillator thicknesses. The use of a converter material, placed directly against the scintillator to improve power deposition, was also investigated. The system was tested in order to and the camera noise characteristics, the optical resolution and magnification and the systems responsivity to power absorption in the scintillator. Using a 137Cs source, preliminary beam proles were obtained. By combining the results of the testing and simulation, predictions of the required length of exposure were made. It was determined that a beam with a flux of 10^6/s and a diameter of 2.5 cm could be profiled, using 6.0 mm of plastic scintillator and 0.6 mm of iron converter, to within 5% error per 0.64 mm x 0.91 mm resolving unit, in less than 1 minute.