Propõe-se, com este trabalho, estudar numericamente se a redundância cinemática e a redundância de atuação podem ser boas alternativas para que manipuladores planares de cinemática paralela atinjam altas acelerações. Sabe-se que estes tipos de redundância promovem uma redução de singularidades do sistema robótico entre outros benefícios. No entanto, a avaliação comparativa do desempenho dinâmico de manipuladores redundantes ainda é pouco estudada. Este estudo não é trivial pois a redundância significa não somente o aumento do torque disponível, mas também que a inércia do sistema foi aumentada. A avaliação numérica deste trabalho se dará por meio do desenvolvimento de modelos cinemáticos e dinâmicos das possíveis configurações de manipuladores paralelos planares com redundância cinemática e redundância de atuação. Esta avaliação pode ser feita pela comparação entre os manipuladores redundantes e o não-redundante para desenvolver uma mesma trajetória do end-effector. Entretanto, esta avaliação é dependente da trajetória, logo esse trabalho também propõe uma avaliação através de um índice dinâmico em toda a área de trabalho dos manipuladores. / The aim of this work is to study numerically if the kinematic redundancy and the actuation redundancy can be good alternatives for parallel planar manipulators to achieve high accelerations. It is known that types of redundancy promote, among other benefits, a significant reduction in the singularities. However, the evaluation of the redundancy as a good solution to increase the dynamic performance was not studied. This study is not trivial because the redundancy means not only that there is more torque available, but also that the inertia of the system has been considerably increased. Different configurations of the redundant manipulator will be evaluated numerically through kinematic and dynamic models. This evaluation can be performed by the comparison among the non redundant manipulator and the redundant manipulators to execute the same task. This evaluation is task dependent, so this work proposes a dynamic index to desing dynamic maps over the workspace.

Propõe-se, com este trabalho, estudar numericamente se a redundância cinemática e a redundância de atuação podem ser boas alternativas para que manipuladores planares de cinemática paralela atinjam altas acelerações. Sabe-se que estes tipos de redundância promovem uma redução de singularidades do sistema robótico entre outros benefícios. No entanto, a avaliação comparativa do desempenho dinâmico de manipuladores redundantes ainda é pouco estudada. Este estudo não é trivial pois a redundância significa não somente o aumento do torque disponível, mas também que a inércia do sistema foi aumentada. A avaliação numérica deste trabalho se dará por meio do desenvolvimento de modelos cinemáticos e dinâmicos das possíveis configurações de manipuladores paralelos planares com redundância cinemática e redundância de atuação. Esta avaliação pode ser feita pela comparação entre os manipuladores redundantes e o não-redundante para desenvolver uma mesma trajetória do end-effector. Entretanto, esta avaliação é dependente da trajetória, logo esse trabalho também propõe uma avaliação através de um índice dinâmico em toda a área de trabalho dos manipuladores. / The aim of this work is to study numerically if the kinematic redundancy and the actuation redundancy can be good alternatives for parallel planar manipulators to achieve high accelerations. It is known that types of redundancy promote, among other benefits, a significant reduction in the singularities. However, the evaluation of the redundancy as a good solution to increase the dynamic performance was not studied. This study is not trivial because the redundancy means not only that there is more torque available, but also that the inertia of the system has been considerably increased. Different configurations of the redundant manipulator will be evaluated numerically through kinematic and dynamic models. This evaluation can be performed by the comparison among the non redundant manipulator and the redundant manipulators to execute the same task. This evaluation is task dependent, so this work proposes a dynamic index to desing dynamic maps over the workspace.

Manipuladores paralelos apresentam inércia reduzida, o que lhes permite alcançar altas acelerações e melhor eficiência energética. Porém, frequentemente seu espaço de trabalho possui desempenho pouco uniforme. De fato, a presença de singularidades paralelas é um forte limitante para essa arquitetura robótica. A redundância de atuação já é conhecida como uma alternativa para essa questão. Enquanto que a redundância cinemática ainda não possui consequências claras. Um manipulador com esse tipo de redundância apresenta um número de graus de liberdade do end-effector menor que o número de graus de liberdade do mecanismo como um todo. Considerando essa lacuna, o objetivo desse mestrado é analisar a influência da redundância cinemática no desempenho de manipuladores paralelos através de simulações e testes experimentais. Tal estudo não é trivial, uma vez que com o maior número de atuadores e graus de liberdade, é adicionada também inércia ao sistema. Foram definidas métricas para avaliar o quão favorável é uma dada posição e, com elas, estratégias de resolução de redundância foram analisadas. A estratégia principal proposta se compõe por duas etapas. No primeiro passo, é definida uma movimentação na qual a posição a cada instante é ótima segundo uma dada métrica de desempenho multiobjetivo. Isso resulta em um movimento de referência que em geral possui altas acelerações. Na segunda etapa, aplica-se uma otimização global, procurando manter um compromisso de proximidade com o movimento de referência e com os níveis de aceleração. Além deste, foram aplicados diversos métodos de otimização local (onde a cinemática inversa é resolvida para cada instante isoladamente) e uma estratégia global truncada. Essas opções foram comparadas numericamente e experimentalmente, trazendo uma resposta objetiva da influência da redundância cinemática no manipulador paralelo. A campanha experimental foi realizada em uma protótipo construído no Laboratório de Dinâmica da Escola de Engenharia de São Carlos. Esse protótipo consiste em um manipulador paralelo planar com 6 graus de liberdade, tendo assim, até 3 graus de redundância para a movimentação no plano. Têm-se 6 motores rotativos para atuá-los, sendo 3 deles acoplados a guias lineares com fusos para obtenção de atuação linear. O acionamento ou não destas guias define o grau de redundância do sistema, garantindo a versatilidade do protótipo. / As a consequence of their reduced inertia, parallel manipulators present superior energetic efficiency and they are able to reach high accelerations. Nevertheless, their workspace has a poorly uniform performance. Indeed, the presence of parallel singularities is a strong limitant for this kind of robots. On the one hand, actuation redundancy is well-known as a good choice in an effort to solve this issue. On the other hand, kinematic redundancy still have unclear consequences on this matter. A kinematically redundant manipulator presents an end-effector with fewer degrees of freedom than the mechanism as a whole. Considering this gap, the objective of this research is to analyze the influence of kinematic redundancy on the performance of parallel manipulators through simulations and experimental tests. This issue turns out to be complex, once traveling actuators sum additional inertia to the system. Metrics are defined in order to evaluate how favourable is a given position, and redundancy resolution strategies are analyzed using them. The main proposed strategy is composed of two steps. In the first one, a movement is defined so that the position for each instant is optimum for a given multiobjective performance metric. This procedure delivers a refererence movement which generally presents high accelerations. On the second step, a global optimization is applied, seeking for a trade-off between the proximity to the reference and the acceleration levels. In addition, several local methods (which resolve the inverse kinematics for each instant independently) and one truncated global strategy were addressed. These configurations were compared numerically and experimentally, delivering a objective analysis of the influence of kinematic redundancy on the performance of the parallel manipulator. The experimental campaign was executed with a physical prototype built at the São Carlos School of Engineering. This is a planar manipulator with 6 degrees of freedom, consequently presenting up to 3 degrees of redundancy. The mechanism is actuated by 6 rotating motors, of which 3 are coupled to leadscrews, resulting in linear actuators. These leadscrews can be locked, defining different degrees of redundancy and granting the versatility of the prototype.

Fault tolerant motor drives are becoming more important in safety critical applications. Although a single motor module fault tolerant drive may be sufficient in some applications, this motor drive only offers limited redundancy. This thesis investigated the dual motor module fault tolerant drive system in which two motor modules were connected electrically in phase and on a common shaft provide redundancy and to increase the reliability of the entire drive system. A general phase current mathematical model to produce the desired output torque was developed to minimize copper loss and torque ripple in the motor drive, which is applicable to both sinusoidal and trapezoidal brushless permanent magnet motor types. A detailed fault effect investigation was performed in this thesis and it is concluded that switch short-circuit fault is the most serious fault since it reduces the electromagnetic torque output significantly and generates larger torque ripple in the motor drive due to the presence of large drag torque. Three fault remedial strategies were proposed to compensate the torque loss and to reduce the torque ripple under different faulty conditions. It is concluded from the analytical results that fault remedial strategy 3 is the tradeoff algorithm in which the zero torque ripple factor can be achieved with only a modest increase in copper loss comparing with the minimum possible value. Two practical dual motor module fault tolerant brushless permanent magnet drive test arrangements with different motor structures were developed in this thesis. The computer simulation studies using the MATLAB Simulink were performed to verify the effectiveness of the proposed fault remedial strategies. The efficiency of the motor drive was predicted based on torque loss measurements and the results were verified in the simulation study. The effect of faults on the drive efficiency was investigated as well. The entire fault tolerant motor drive control system was also developed to verify the analytical and simulation results. A fault detection and identification method to detect switch open-circuit faults, switch short-circuit faults, and the winding short-circuit faults was also proposed. Its advantages are the simplicity of the implementation and reduction of the cost of the drive system. The experimental results demonstrated that the proposed fault remedial strategies can be implemented in real time motor control and are effective to compensate the torque loss and reduce the torque ripple. / Thesis (Ph.D.) -- University of Adelaide, School of Electrical and Electronic Engineering, 2008

Fault tolerant motor drives are becoming more important in safety critical applications. Although a single motor module fault tolerant drive may be sufficient in some applications, this motor drive only offers limited redundancy. This thesis investigated the dual motor module fault tolerant drive system in which two motor modules were connected electrically in phase and on a common shaft provide redundancy and to increase the reliability of the entire drive system. A general phase current mathematical model to produce the desired output torque was developed to minimize copper loss and torque ripple in the motor drive, which is applicable to both sinusoidal and trapezoidal brushless permanent magnet motor types. A detailed fault effect investigation was performed in this thesis and it is concluded that switch short-circuit fault is the most serious fault since it reduces the electromagnetic torque output significantly and generates larger torque ripple in the motor drive due to the presence of large drag torque. Three fault remedial strategies were proposed to compensate the torque loss and to reduce the torque ripple under different faulty conditions. It is concluded from the analytical results that fault remedial strategy 3 is the tradeoff algorithm in which the zero torque ripple factor can be achieved with only a modest increase in copper loss comparing with the minimum possible value. Two practical dual motor module fault tolerant brushless permanent magnet drive test arrangements with different motor structures were developed in this thesis. The computer simulation studies using the MATLAB Simulink were performed to verify the effectiveness of the proposed fault remedial strategies. The efficiency of the motor drive was predicted based on torque loss measurements and the results were verified in the simulation study. The effect of faults on the drive efficiency was investigated as well. The entire fault tolerant motor drive control system was also developed to verify the analytical and simulation results. A fault detection and identification method to detect switch open-circuit faults, switch short-circuit faults, and the winding short-circuit faults was also proposed. Its advantages are the simplicity of the implementation and reduction of the cost of the drive system. The experimental results demonstrated that the proposed fault remedial strategies can be implemented in real time motor control and are effective to compensate the torque loss and reduce the torque ripple. / Thesis (Ph.D.) -- University of Adelaide, School of Electrical and Electronic Engineering, 2008

Manipuladores paralelos apresentam inércia reduzida, o que lhes permite alcançar altas acelerações e melhor eficiência energética. Porém, frequentemente seu espaço de trabalho possui desempenho pouco uniforme. De fato, a presença de singularidades paralelas é um forte limitante para essa arquitetura robótica. A redundância de atuação já é conhecida como uma alternativa para essa questão. Enquanto que a redundância cinemática ainda não possui consequências claras. Um manipulador com esse tipo de redundância apresenta um número de graus de liberdade do end-effector menor que o número de graus de liberdade do mecanismo como um todo. Considerando essa lacuna, o objetivo desse mestrado é analisar a influência da redundância cinemática no desempenho de manipuladores paralelos através de simulações e testes experimentais. Tal estudo não é trivial, uma vez que com o maior número de atuadores e graus de liberdade, é adicionada também inércia ao sistema. Foram definidas métricas para avaliar o quão favorável é uma dada posição e, com elas, estratégias de resolução de redundância foram analisadas. A estratégia principal proposta se compõe por duas etapas. No primeiro passo, é definida uma movimentação na qual a posição a cada instante é ótima segundo uma dada métrica de desempenho multiobjetivo. Isso resulta em um movimento de referência que em geral possui altas acelerações. Na segunda etapa, aplica-se uma otimização global, procurando manter um compromisso de proximidade com o movimento de referência e com os níveis de aceleração. Além deste, foram aplicados diversos métodos de otimização local (onde a cinemática inversa é resolvida para cada instante isoladamente) e uma estratégia global truncada. Essas opções foram comparadas numericamente e experimentalmente, trazendo uma resposta objetiva da influência da redundância cinemática no manipulador paralelo. A campanha experimental foi realizada em uma protótipo construído no Laboratório de Dinâmica da Escola de Engenharia de São Carlos. Esse protótipo consiste em um manipulador paralelo planar com 6 graus de liberdade, tendo assim, até 3 graus de redundância para a movimentação no plano. Têm-se 6 motores rotativos para atuá-los, sendo 3 deles acoplados a guias lineares com fusos para obtenção de atuação linear. O acionamento ou não destas guias define o grau de redundância do sistema, garantindo a versatilidade do protótipo. / As a consequence of their reduced inertia, parallel manipulators present superior energetic efficiency and they are able to reach high accelerations. Nevertheless, their workspace has a poorly uniform performance. Indeed, the presence of parallel singularities is a strong limitant for this kind of robots. On the one hand, actuation redundancy is well-known as a good choice in an effort to solve this issue. On the other hand, kinematic redundancy still have unclear consequences on this matter. A kinematically redundant manipulator presents an end-effector with fewer degrees of freedom than the mechanism as a whole. Considering this gap, the objective of this research is to analyze the influence of kinematic redundancy on the performance of parallel manipulators through simulations and experimental tests. This issue turns out to be complex, once traveling actuators sum additional inertia to the system. Metrics are defined in order to evaluate how favourable is a given position, and redundancy resolution strategies are analyzed using them. The main proposed strategy is composed of two steps. In the first one, a movement is defined so that the position for each instant is optimum for a given multiobjective performance metric. This procedure delivers a refererence movement which generally presents high accelerations. On the second step, a global optimization is applied, seeking for a trade-off between the proximity to the reference and the acceleration levels. In addition, several local methods (which resolve the inverse kinematics for each instant independently) and one truncated global strategy were addressed. These configurations were compared numerically and experimentally, delivering a objective analysis of the influence of kinematic redundancy on the performance of the parallel manipulator. The experimental campaign was executed with a physical prototype built at the São Carlos School of Engineering. This is a planar manipulator with 6 degrees of freedom, consequently presenting up to 3 degrees of redundancy. The mechanism is actuated by 6 rotating motors, of which 3 are coupled to leadscrews, resulting in linear actuators. These leadscrews can be locked, defining different degrees of redundancy and granting the versatility of the prototype.

Call number: LD2668 .T4 1978 K87 / Master of Science

Two well-known methods of improving the reliability of a system are (i) provision of redundant units, and (ii) repair maintenance. In a redundant system more units made available for performing the system function when fewer are required actually. There are two major types of redundancy - parallel and standby. In this dissertation we are concerned with both these types. Some of the typical assumptions made in the analysis of redundant systems are (i) the repair facility can take up a failed unit for repair at any time, if no other unit is undergoing repair (ii) the system under consideration is needed all the time However, we frequently come accross systems where one or more assumptions have to be relaxed. This is the motivation for the detailed study of the models presented in this dissertation. In this dissertation we present models of redundant systems relaxing one or more of these assumptions simultaneously. More specifically it is a study of stochastic models of redundant systems with 'vacation period' for the repair facility (both standby and parallel systems), and intermittently used systems. The dissertation contains five chapters. Chapter 1 is introductory in nature and contains a brief description of the mathematical techniques used in the analysis of redundant systems. In Chapter 2 assumption (i) is relaxed while studying a model of cold standby redundant system with 'vacation period' for the repair facility. In this model the repair facility is not available for a random time immediately after each repair completion. Integral equations for the reliability and availability functions of the system are derived under suitable assumptions. In Chapter 3, once again assumption (i) is relaxed while studying a model of parallel redundant systems with the same 'vacation period' for the repair facility, explained in the above paragraph. In Chapter 4, the detailed review of intermittently used systems have been studied. In Chapter 5, assumption (ii) is relaxed. This chapter is devoted to the study of an intermittently used 2-unit cold standby system with a single repair facility. This study was carried out using the 'correlated alternating renewal process' and the joint forward recurrence times. All the above models have been studied, when some of the underlying distributions have a non-Markovian nature. They have been analysed using a regeneration point technique. / Mathematical Sciences / M. Sc. (Statistics)

ITC/USA 2008 Conference Proceedings / The Forty-Fourth Annual International Telemetering Conference and Technical Exhibition / October 27-30, 2008 / Town and Country Resort & Convention Center, San Diego, California / ARINC 664 presents the designers of data acquisition systems challenges not previously seen on other aircraft avionic buses. Among the biggest challenges are providing the test instrumentation system with the capacity to process two redundant Ethernet segments that may be carrying packet traffic at near wire-line speed. To achieve this level of performance, the hardware and software must not only perform mundane operations, like time stamping and simple virtual link MAC filtering, but also need to implement core ARINC 664 functions like redundancy management and integrity checking. Furthermore, other TCP/IP operations, such as IP header checksum, must also be offloaded to the hardware in order to maintain real-time operation. This paper describes the implementation path followed by TTC during its development of an ARINC 664 network monitor used in a large commercial aircraft flight test program.

ITC/USA 2011 Conference Proceedings / The Forty-Seventh Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2011 / Bally's Las Vegas, Las Vegas, Nevada / The National Oceanic and Atmospheric Administration (NOAA) Jason Ground System (NJGS) is a consolidated next-generation ground system that will support the simultaneous operation of the OSTM/Jason-2 and Jason-3 ocean surface topography missions. The NJGS will consist of several independent subsystems for spacecraft command and control, telemetry processing, and data archiving and distribution. The existing NOAA Jason-2 Ground System (J2GS) was designed around the concept of subsystem "strings", in which two complete sets of subsystems acted in primary and standby roles. For the NJGS, this concept is replaced with subsystem-level redundancy, in which two or more instances of each subsystem independently provide redundant capabilities. This paper discusses the design elements involved in the provision of a ground system architecture providing redundancy at the subsystem level. The paper focuses on the interaction between primary and standby subsystems and the mechanism through which failover capabilities are provided across the ground system.