The purpose of this thesis was to develop an economical, sustainable, and environmentally friendly straw Medium Density Fibreboard (MDF) process, capable of full-scale manufacturing and to produce MDF of requested quality. The investigated straw was based on wheat (Triticum aestivum L.) and rice (Oryzae sativa L.). In this thesis three different methods were taken for manufacture of straw MDF; (A) wheat-straw fibre was blowline blended with melamine-modified urea-formaldehyde (MUF), (B) rice-straw fibre was mixed with methylene diphenyl diisocyanate (MDI) in a resin drum-blender, and (C) wheat-straw fibre was activated in the blowline by the addition of Fenton’s reagent (H2O2/Fe2+) for production of non-resin MDF panels.  The MUF/wheat straw MDF panels were approved according to the requirements of the EN standard for MDF (EN 622-5, 2006). The MDI/rice-straw MDF panels were approved according to requirements of the standard for MDF of the American National Standard Institute (ANSI A208.2-2002). The non-resin wheat-straw panels showed mediocre MDF panel properties and were not approved according to the requirements in the MDF standard. The dry process for wood-based MDF was modified for production of straw MDF. The straw MDF process was divided into seven main process steps. 1.       Size-reduction (hammer-milling) and screening of straw 2.       Wetting and heating of straw 3.       Defibration 4.       Resination of straw fibre 5.       Mat forming 6.       Pre-pressing 7.       Hot-pressing       The primary results were that the straw MDF process was capable of providing satisfactory straw MDF panels based on different types of straw species and adhesives. Moreover, the straw MDF process was performed in pilot-plant scale and demonstrated as a suitable method for producing straw MDF from straw bales to finished straw MDF panels. In the environmental perspective the agricultural straw-waste is a suitable source for producing MDF to avoid open field burning and to capture carbon dioxide (CO2), the biological sink for extended time into MDF panels, instead of converting straw directly into bio energy or applying straw fibre a few times as recycled paper. Additionally, the straw MDF panels can be recycled or converted to energy after utilization. A relationship between water retention value (WRV) of resinated straw fibres, the thickness swelling of corresponding straw MDF panels, and the amount of applied adhesive was determined. WRV of the straw fibre increased and the TS of straw MDF declined as a function of the resin content. The empirical models developed were of acceptable significance and the R2 values were 0.69 (WRV) and 0.75 (TS), respectively. Reduced thickness swelling of MDF as the resin content is increased is well-known. The increase of WRV as a function of added polymers is not completely established within the science of fibre swelling. Fortunately, more fundamental research can be initiated and likely a simple method for prediction of thickness swelling of MDF by analysis of the dried and resinated MDF fibres is possible. / Syftet med denna avhandling var att lägga grunden för en ekonomisk, hållbar och miljövänlig MDF process för halmråvara, kapabel för fullskalig produktion av MDF och goda skivegenskaper. Framställningen av MDF skivor utgick från halm av vete (Triticum aestivum L.) och ris (Oryzae sativa L.). Tre olika metoder användes för att producera MDF av halm; (A) fibrer av vetehalm belimmades i blåsledning med ett melaminmodifierat urea-formaldehydlim (MUF), (B) fibrer av rishalm belimmades i en limblandare med metylen difenyl diisocyanate (MDI), (C) Limfria MDF skivor av vetehalm framställdes med aktivering av fibrer genom tillsats av Fenton´s reagens (H2O2/Fe2+) i blåsledning utan någon tillsats av syntetiskt lim. Sammanfattningsvis kan det understrykas att framställda MDF-skivor av MUF/vetehalm var godkända enligt standard för MDF (EN 622-5, 2006). Dessutom var framställda MDF skivor av MDI/rishalm också godkända enligt krav i standard för MDF ”American National Standard Institute” (ANSI A2008.2-2002). Limfria vetehalmskivor visade på måttliga skivegenskaper och klarade inte kraven i MDF standard.   Fiberframställningsprocessen för MDF modifierades till en produktion utgående från halm. MDF processen för halm delades upp i sju primära processoperationer.   (1)            Storleksreducering och sållning av halm (2)            Vätning och uppvärmning av halm (3)            Defibrering (4)            Belimning av halmfiber (5)            Mattformning (6)            Förpressning (7)            Pressning   De viktigaste resultaten från denna studie är att MDF av halm kunde produceras utgående från olika typer av halmsorter och lim. Dessutom utfördes MDF-processen i pilotskala och visade på en lämplig metod för framställning av MDF-skivor från halmbalar till färdiga halmfiberskivor. Det miljömässiga perspektivet på att använda jordbruksavfall till framställning av halmskivor är att undvika förbränning av halm ute på fältet, men det är även möjligt att binda koldioxid (CO2) i halmskivor under längre tid än att omsätta halmråvaran omedelbart som bioenergi eller använda halmfiber som returpapper några få gånger. Dessutom kan MDF återanvändas eller bli omsatt till energi efter användning.   Ett förhållande mellan ”water retention value” (WRV), av belimmade halmfiber, tjocklekssvällning för motsvarande MDF av halmskivor och mängden av tillsatt lim vid olika nivåer har undersökts. Med ökande limhalt tilltog WRV fibersvällning, vidare minskade tjocklekssvällning för motsvarande MDF skivor. De framtagna empiriska modellerna var godtagbara och beräknade R2 värden var 0.69 (WRV) och 0.75 (TS). Minskad tjocklekssvällning med ökad limhalt är dokumenterad sen tidigare. Ökad fibersvällning WRV vid tillsats av polymerer (limmer) är inte fullständigt etablerad inom vetenskapen för fibersvällning. Lyckligtvis kan grundläggande forskning initieras och sannolikt föreligger en enkel metod för att prediktera tjocklekssvällning av MDF genom analyser av torkade och belimmad MDF fiber.

科学研究費補助金 研究種目:基盤研究(B)(2) 課題番号:10555255 研究代表者:藤澤 敏治 研究期間:1998-2000年度

The effect of microwave radiation on the prepared 0.5Fe/ZSM-5 catalysts as a post-synthesis modification step was studied in the methanol-to-hydrocarbons process using the temperature-programmed surface reaction (TPSR) technique. This was achieved by preparing a series of 0.5Fe/ZSM-5 based catalysts under varying microwave power levels (0–700 W) and over a 10 s period, after iron impregnating the HZSM-5 zeolite (Si/Al = 30 and 80). Physicochemical properties were determined by XRD, SEM, BET, FT-IR, C3H9N-TPSR, and TGA techniques. It was found that microwave radiation induced few changes in the bulk properties of the 0.5Fe/ZSM-5 catalysts, but their surface and catalytic behavior were distinctly changed. Microwave radiation enhanced crystallinity and mesoporous growth, decreased coke and methane formation, decreased the concentration of Brønsted acidic sites, and decreased surface area and micropore volume as the microwave power level was increased from 0 to 700 W. From the TPSR profiles, it was observed that microwave radiation affects the peak intensities of the produced hydrocarbons. Application of microwave radiation shifted the desorption temperatures of the MTH process products over the HZSM-5(30) and HZSM-5(80) based catalysts to lower and higher values respectively. The MeOH-TPSR profiles showed that methanol was converted to DME and subsequently converted to aliphatic and aromatic hydrocarbons. It is reasonable to suggest that microwave radiation would be an essential post-synthesis modification step to mitigate coke formation and methane formation and increase catalyst activity and selectivity. / Chemical Engineering / M. Tech. (Chemical Engineering)

Made available in DSpace on 2016-03-15T19:36:54Z (GMT). No. of bitstreams: 1 Maria Claudia Lopes Guerra.pdf: 9968717 bytes, checksum: 7d0e4986884ffa382a835b641ed76573 (MD5) Previous issue date: 2015-06-12 / Fundo Mackenzie de Pesquisa / The ECAP (Equal Channel Angular Pressing) is a mechanical process of Severe Plastic Deformation (SPD) where a sample is subjected to a shearing force when passing through the region of intersection of two channels. The main goal of this method is Severe Plastic Deformation achieve a microstructure with ultrafine grains, which have much higher than the equivalent coarse grain materials physical properties, such as an increase in strength and toughness simultaneously. What makes this increasingly interesting technique is that as there is no reduction cross section is possible to obtain plastic strain accumulation and therefore gain in grain order of nanometer scale. The great advantage of ECAP is to achieve a much higher degree of strain hardening than obtained by conventional methods of plastic deformation, and consequently a grain refining much higher as well. The importance of the study of severe plastic deformation process is on improving the mechanical performance of the materials and the possibility of a better understanding of the mechanisms of strain hardening, which may indicate a new path for producing high-strength materials, possibly scaled industrial. In this work are presented the microstructural, mechanical and electrical analysis of the aluminum alloy AA 1050 samples, commonly used for electrical purposes, with ultrafine grains (typical grain size below a micron) resulting from processing by ECAP, based on the method of SPD. / A PCE (Prensagem em Canais Equiangulares) consiste num processo mecânico de Deformação Plástica Intensa (DPI) onde um corpo de prova é sujeito a um esforço de cisalhamento ao passar pela região de intersecção de dois canais. Os principais objetivos desse método de Deformação Plástica Intensa é alcançar uma microestrutura com grãos ultrafinos, os quais possuem propriedades físicas muito superiores aos equivalentes materiais de grãos grosseiros, como um aumento em resistência mecânica e tenacidade simultâneas. O que torna esta técnica cada vez mais interessante é que como não há redução da seção transversal é possível obter acumulo de deformação plástica e com isso obter grãos na ordem de escala nanométrica. A grande vantagem do PCE é alcançar um grau de encruamento muito superior do que obtido por métodos convencionais de deformação plástica, e consequentemente, um refino de grão muito superior também. A importância do estudo do processo de deformação plástica intensa está na melhoria do desempenho mecânico dos materiais e na possibilidade de uma melhor compreensão dos mecanismos de encruamento, fato que pode indicar um novo caminho para a produção de materiais de alta resistência mecânica, possivelmente em escala industrial. Nesse trabalho são apresentadas as análises microestruturais, mecânicas e elétricas de amostras de ligas de alumínio AA 1050, comumente utilizadas para fins elétricos, com estrutura de grãos ultrafinos (tamanho de grão típico abaixo de um micrometro) resultantes do processamento por PCE, baseada no método de DPI.

A mixed integer programming model is developed to determine a logistical design for maximizing rates of return to harvest, storage, transportation, and bioreflning of herbaceous crop residue for production of biofuels and feed for ruminant animals. The primary objective of this research is to identify the optimal location, scale, and number of pretreatment and biorefinery plants in northeastern North Dakota. The pretreatment and biorefinery plants are modeled under the assumption that they utilize recent technological advancement in AFEX and Simultaneous Saccharification and Fermentation, respectively. Potential feedstocks include wheat straw, barley straw, Durum straw, and com stover. Results indicate that the minimum ethanol rack price that will effectively trigger the production of cellulosic ethanol is $1.75 per gallon.