The primary aim of this research was to investigate the behaviour of a clay subjected to a loading regime similar to that experienced by a road subgrade under traffic loading in Great Britain. The material used was Keuper Marl. The samples were anisotropically consolidated in a triaxial apparatus from a slurry which allowed careful control over the stress history and produced uniform samples. The samples were fully instrumented and the apparatus was capable of applying repeated axial and radial stresses. The test programme was designed to investigate the resilient and permanent response of the samples to a variety of stress pulse magnitudes and time periods. The main conclusions were: i) The material exhibited a marked stress softening. ii) The mean normal effective stress remained constant under a variety of total stress paths over the range of frequencies tested. iii) The resilient response was found to depend on the magnitude of the applied stress pulse and the mean normal effective pressure, and to be independent of the preconsolidation pressure. iv) The material exhibited significant thixotropy. A smaller parallel series of tests was carried out on compacted triaxial samples of three clays (Keuper Marl, Gault clay and London clay) in a simple pneumatic repeated load triaxial rig. The test programme was designed to investigate the resilient response of the samples over a range of repeated deviator stresses. The suction moisture content relationship for each clay was established, and the resilient response of the clay was found to be controlled by the magnitude of the stress pulse and the suction. A series of California Bearing Ratio tests was carried out on compacted samples of the three clays, and on anisotropically consolidated samples of Keuper Marl, to allow a comparison to be made between the resilient modulus and CBR. A review of previous work is presented.

The demands on asphalt pavements, as a result of the growth in traffic volumes, traffic loads and tyre contact pressures, has resulted in an increased interest in the use of modified bitumens, particularly over the last ten years. Of the various types of modified and specialised binders that are available worldwide, polymer modified bitumens (PMB’s) have tended to be the most popular. Polymer modification significantly alters the rheological characteristics of the binder, thereby requiring the use of fundamental rheological testing methods rather than empirical methods, to provide an indication of the performance of the binder and subsequently the asphalt mixture. This thesis is concerned with the use of a Dynamic Shear Rheometer (DSR) to quantify the fundamental rheological characteristics of various unaged and aged PMB’s. The parallel plate testing methodology used with the Bohlin Model DSR50 Dynamic Shear Rheometer requires accurate temperature control by means of a circulating fluid bath, a combination of different plate diameters and sample geometries, and the use of small strains in order to measure the linear viscoelastic rheological characteristics of a bitumen specimen. Conventional and dynamic shear rheometry testing of various penetration grade bitumens, semi-crystalline ethylene vinyl acetate (EVA) PMB’s and thermoplastic rubber styrene butadiene styrene (SBS) PMB’s have indicated that the rheological characteristics differ considerably between the unmodified and polymer modified bitumens as well as between the plastomeric EVA and elastomeric SBS PMB’s. The DSR dynamic rheological parameters of complex modulus and phase angle indicate that the modification mechanism of EVA PMB’s consists of the crystallisation of rigid three dimensional networks within the bitumen. These rigid crystalline structures increase the stiffness and elastic component of the viscoelastic balance of the PMB up to the temperature associated with the melting of the copolymer. The modification mechanism of SBS PMB’s consists of the establishment of a highly elastic network within the bitumen that increases the elasticity and stiffness, particularly at high temperatures. The higher melting temperature of the SBS copolymer allows the rheological character of the SBS PMB to extend to temperatures greater than those found for EVA PMB’s. DSR measurements of the rheological changes associated with laboratory ageing of EVA PMB’s indicate that the ageing mechanism is linked to a chemical change of the copolymer due to fusion of the crystallites. This chemical change leads to a degradation of the polymer and, therefore, a transition of the rheological behaviour towards that of an unmodified bitumen. The rheological changes associated with the ageing of SBS PMB’s is linked to a breakdown of the molecular structure of the SBS copolymer to form a lower molecular weight polymer substructure. This results in an increased viscous behaviour after ageing compared to the increased elastic behaviour found for unmodified bitumens.

As part of a European Union funded research study (the "SCIENCE" project) performed between 1990 and 1993, granular road construction material and subgrade soil specimens were tested in the four participating laboratories of the project: Laboratório Nacional de Engenharia Civil Portugal University of Nottingham United Kingdom Laboratoire Central des Ponts et Chaussées France Delft University of Technology The Netherlands The author was based the first of these and visited the other participating laboratories, performing the majority of the work described. Inaccuracies in repeated load triaxial testing based on the use of different apparatus and instrumentation are identified. A detailed instrumentation comparison is undertaken, which results in the magnitude of potential errors being quantified. The author has derived material parameters and model coefficients for the materials tested using a number of previously published material models. In order to establish these parameters a method for removing outliers from test data based on the difference between the modelled and experimental material parameters for each stress path applied was developed. The consequences of repeatability and reproducibility, variability and inaccuracies in the output of repeated load triaxial testing, on the parameters and, hence, on computed pavement design thicknesses or life is investigated using a number of material models and the South African mechanistic pavement design method. Overall, it is concluded that: • Instrumentation differences are not as critical as variations in results obtained from different specimens tested in a single repeated load triaxial apparatus. It was found that specimen manufacture difference yielded greater variation that instrumentation differences. • Variation in results has some effect on the upper granular layers, where higher stress levels are experienced, but even quite considerable variation in the results from materials used in the lower layers has little effect on pavement life. • Analytical methods to determine the stresses and strains vary considerably as do the predicted pavement thicknesses consequent on using these methods. The inaccuracies in testing (large discrepancies are found when the same material is tested in the same laboratory) and the limitations of the available material models severely limit the usefulness of advanced testing and non-linear modelling in routine pavement design. On the basis of this study it is recommended that a more simplistic pavement design approach be taken keeping in line with future developments of testing and modelling and field validation.

Little effort has been made to apply the Critical State Soil Mechanics concept to the prediction of pavement response. The aim of this research is to apply soil mechanics principles, particularly the kinematic hardening concept, to the prediction of the response of lightly trafficked pavements to repeated loading. For this purpose, the finite element critical state program CRISP is used. A comparison is made between the predictions given by the three-surface kinematic hardening (3-SKH) model and a layered elastic analysis BISAR for the resilient deformation produced by repeated loading of a thinly surfaced pavement, and the models are found to be in good agreement. The ability of the 3-SKH model to predict soil behaviour under cyclic loading, and under one-dimensional loading, unloading and reloading is also evaluated. A comparison between model predictions and experimental data obtained by other researchers shows that the 3-SKH model over-predicts the value of K0,nc and hence shear strain during monotonic loading. This problem is magnified when the model is applied to cyclic loading behaviour where large numbers of cycles are involved. The model also predicts an accumulation of negative shear strain with increasing number of cycles under some stress conditions. This will lead to unrealistic predictions of rutting in pavements. However, the model is suitable for obtaining resilient parameters for input to a layered elastic analysis program. A new model, which is a modified version of the 3-SKH model, is therefore proposed by modifying the flow rule and the hardening moduli. This model can correctly predict the value of K0,nc and reduce the amount of shear strain predicted. The model also eliminates the problem of accumulation of negative shear strain with increasing number of cycles. The new model introduces two additional parameters, one of which can be determined by one-dimensional normal compression test, and the other by fitting a set of cyclic loading data. The new model is used to design the required thickness of granular material using the permissible resilient subgrade strain and permanent rut depth criteria during construction. It is found that the new model predicts a realistic granular layer thickness required to prevent excessive rutting, thus showing much promise for use in design of thinly surfaced pavements.

Research has been conducted into the fundamental mechanical properties of a granular material. This has involved the use of both a repeated load triaxial apparatus and a new hollow cylinder apparatus, which has required development and modification. Building on the foundation of earlier research at Nottingham, models have been developed which predict the stress-strain behaviour of a dry granular material under any combination of applied stresses. This includes repeatable elastic behaviour and the development of irrecoverable plastic strain. The accuracy of these models has been tested as far as possible using available test equipment. The effects of varying particle gradation, degree of compaction, maximum particle size and mineral type have been explored using a repeated load triaxial apparatus. The effect of moisture has also been investigated with respect to both full and partial saturation. A computer program (GRANMAT) has been written, which makes use of the stress-strain equations developed, to analyse a road pavement structure consisting of thin bituminous surfacing, granular base and subgrade. The reliability of the program has been assessed and areas of necessary improvement indicated. In-situ testing at a number of road sites is described and analysed with respect to both the effect of compaction on a granular road foundation and the use of a number of in-situ test devices. Finally, the information gained, in the laboratory and on site, is brought together in a series of design suggestions for granular road foundations, with particular reference to results from the GRANMAT computer program.

In order to control stormwater runoff engineers and hydrologists have used various techniques to attempt to reduce or delay the volume of water which reaches the sewer system. Recently, international approaches have favoured the idea of "source control" or "on-site" retention. This technique stores water in areas close to the point at which precipitation lands. Permeable pavements and similar stormwater control devices have not been exploited in the United Kingdom. Their adoption has been hindered by a lack of knowledge of their hydrological performance. This research aims to produce information on the hydrological performance of a car park surface and to produce a model which can predict the hydrological response to varying rainfall inputs. The objective of this thesis is to examine the hydrological behaviour of a model car park surface under varying rainfall conditions. The study has involved the construction of full-scale permeable pavement model car park structures and a rainfall simulator for use in the laboratory. A monitoring procedure was developed in order to measure inputs and changes in drainage, storage and evaporation over short (less than 2 hours) and long (up to 3 months) time scales. A range of rainfall simulations were applied to the model car park surfaces which differed in intensity, duration and volume. Hydrological processes were monitored over an 18 month period. Results suggest that evaporation, discharge and retention in the structures were strongly influenced by the particle size of the bedding material and the surface blocks. In general an average of 55% of a 15 mm 11-1 rainfall event could be retained by an initially dry structure. Subsequent simulations suggest that approximately 30% of a 15 mm rainfall event could be stored by an initially wet structure (with a minimum time interval of 72 hours). Sediments were also applied to the car park structures in order to monitor the effects of clogging on hydrological performance and to quantify the ability of the structures to act as a primary screening site for sediments. The application of sediments to the structure showed that evaporation from the structure increased by as much as 25-30%. Laboratory simulation of clogging effects was also compared to data gathered from field sites and the results suggested that laboratory simulations provided a good approximation of the migration of sediments in the structure. A model of the hydrological performance of the structure has been developed to be used as a predictive tool. The model relates rainfall inputs to water retention and discharge output over consecutive rainfall events. It also allows evaporation and long-term retention by the structure to be estimated over differing lengths of dry periods. The model results indicate that discharge was predicted to an accuracy of 78% (based on a percentage difference between the observed and predicted values), and evaporation and retention were predicted to an accuracy of 80%.

No description available.

In this research, a new approach for arterial road travel time estimation and prediction has been proposed and developed for providing reliable dynamic travel time information for arterial road networks. The results of the research should benefit arterial road traffic management and some travel time related applications. / Thesis (PhD)--University of South Australia, 2008.

One of the important components of Intelligent Transport Systems (ITS) are the Advanced Traveller Information Systems (ATIS) that provide traffic information to manage traffic flow on existing road networks more efficiently. / Variable Messages Signs (VMS) are one of the key instruments of ATIS for providing en-route traveller information. These signs offer significant potential to resolve urban traffic management issues, such as reducing congestion and increasing network efficiency. The system also delivers considerable personal benefits by assisting drivers to make route choice decisions. / Much research has validated the effectiveness of VMS information on route choice decisions, however, the relationship between route choice behaviour and information content is still not clear. Also, the results show large variation when factors such as the influence of road type, toll roads and degree of congestion are considered. / The primary aims of this research are to investigate route choice behaviour in response to the message content of VMS and to develop route choice models targeted on an arterial road in the Adelaide Central Business District (CBD). The study investigates the influences of VMS message content on drivers taking into account their differing characteristics and experience, including socio-economic factors and trip characteristics. / Two major surveys, a stated preference (SP) survey and a revealed preference (RP) survey, were performed. An anonymous mail-back SP survey questionnaire was conducted with residents along a target route in Adelaide in order to collect drivers' route choice behaviour in response to hypothetical VMS messages. The RP survey was conducted to collect data in the real world situation. A VMS message was displayed to drivers and actual route choice behaviour was measured using anonymous mail-back questionnaires and by observation of traffic volumes. A total of 245 (of 1000 distributed) and 183 (of 500 distributed) replies were used for model development. / A binary logit approach was employed to develop route choice models using data obtained from the SP survey. Goodness-of-fit and hypothesis testing of the model showed that the developed models fitted the data well and estimated parameters were statistically significant at the 5% level. / Thesis (MEng(TransportSystemsEng))--University of South Australia, 2004.

Thesis (M.S.)--Oregon State University, 2008. / Printout. Includes bibliographical references (leaves 73-76). Also available on the World Wide Web.