Flax shives are a source of abundant biomass from renewable sources. They are considered to be environmentally benign and have a high-energy content for heating and generation of electricity, but only after being processed into pellets. Pelleting of the shives was done by using the single-pelleter and pilot-scale mill. The effect of grinding with screens of 2.4, 3.2, and 6.4 mm on unit density and durability was conducted with a completely randomized design using shives from Biofibre Industries Inc., Canora, SK. The central composite face-centered design with 3 levels of lower grade canola meal used as a binder (18, 21, and 24%), moisture content (8, 11, and 14% (w.b)), and hammer mill screen size (3.2, 4.8, and 6.4 mm) was used to determine the effects of these three factors on the properties of fuel pellets made from shives obtained from Biolin Research Inc., Saskatoon, SK. The initial moisture content of coarse flax shives from both sources was about 10.5% wet basis (w.b.). The moisture content of flax shive grinds ranged from 9.6 to 10.5% (w.b.) after grinding, using the smaller screens for the Biofibre material, while the moisture content ranged from 7.9 to 8.6% (w.b.) for shives from Biolin. Also, smaller screen size reduced the geometric mean particle size for shives from both sources. The use of the smaller hammer mill screen resulted in an increase in both bulk and particle density of shives. There was a decrease in coefficient of the internal friction of shives from 0.20 to 0.14 and an increase in a cohesion of shives from 2.18 to 3.83 kPa when the screen size decreased from 6.4 to 3.2 mm. The flax shives contained cellulose (53.27%), hemicelluloses (13.62%), and lignin (20.53%) at a moisture content of 7.9% (w.b). Specific heat capacity of flax shives changed from 1.5 to 2.7 kJ/ (kg °C) when the moisture content was increased from 8 to14% (w.b.) and temperature from 15 to 80°C. The shives had the combustion energy of 17.67 MJ/kg at a moisture content of 8.1% (w.b.).<p> The smallest screen size (2.4 mm) resulted in the highest unit density (1010 kg/m3) and the highest durability (88%) in the pellets produced by the single-pelleting equipment. The change in length of pellets produced by the pilot-scale mill increased as canola meal increased from 18 to 24% at the highest moisture content (%). The pellets were more stable at the highest moisture content when the lowest canola meal used. The addition of 18% canola meal and grinds from a screen size of 6.4 mm produced the highest unit density in the pellets at all moisture levels. The highest bulk density (682 kg/m3) was obtained from shive mixtures with 18% canola meal and a moisture content of 8%. The highest hardness and durability were found for the shive pellets that were produced with 18% canola meal at a moisture content of 14% (w.b). Pellets that were produced at a moisture content of 14% (w.b) resulted in the lowest percentage of moisture absorption. The inclusion of the canola meal in the shive mixture resulted in an increase in the combustion energy of the pellets because of the fat content in the binder. The two levels of canola meal for shive pellets had essentially the same level of emissions. However, there were significant differences between shive pellets and commercial wood pellets in the level of the emissions. Lower amounts of methane (1.29 ppm) and oxygen (164.3 ppt) were found for flax shive pellets than of methane (1.63 ppm) and oxygen (176.6 ppt) in commercial wood pellets.<p> In short, pelleting of flax shives into fuel pellets improved the handling characteristics, increased bulk density and energy content. Fuel pellets made from flax shives had less emission of methane and oxygen from combustion when compared to commercial wood pellets.

Flax shives are a source of abundant biomass from renewable sources. They are considered to be environmentally benign and have a high-energy content for heating and generation of electricity, but only after being processed into pellets. Pelleting of the shives was done by using the single-pelleter and pilot-scale mill. The effect of grinding with screens of 2.4, 3.2, and 6.4 mm on unit density and durability was conducted with a completely randomized design using shives from Biofibre Industries Inc., Canora, SK. The central composite face-centered design with 3 levels of lower grade canola meal used as a binder (18, 21, and 24%), moisture content (8, 11, and 14% (w.b)), and hammer mill screen size (3.2, 4.8, and 6.4 mm) was used to determine the effects of these three factors on the properties of fuel pellets made from shives obtained from Biolin Research Inc., Saskatoon, SK. The initial moisture content of coarse flax shives from both sources was about 10.5% wet basis (w.b.). The moisture content of flax shive grinds ranged from 9.6 to 10.5% (w.b.) after grinding, using the smaller screens for the Biofibre material, while the moisture content ranged from 7.9 to 8.6% (w.b.) for shives from Biolin. Also, smaller screen size reduced the geometric mean particle size for shives from both sources. The use of the smaller hammer mill screen resulted in an increase in both bulk and particle density of shives. There was a decrease in coefficient of the internal friction of shives from 0.20 to 0.14 and an increase in a cohesion of shives from 2.18 to 3.83 kPa when the screen size decreased from 6.4 to 3.2 mm. The flax shives contained cellulose (53.27%), hemicelluloses (13.62%), and lignin (20.53%) at a moisture content of 7.9% (w.b). Specific heat capacity of flax shives changed from 1.5 to 2.7 kJ/ (kg °C) when the moisture content was increased from 8 to14% (w.b.) and temperature from 15 to 80°C. The shives had the combustion energy of 17.67 MJ/kg at a moisture content of 8.1% (w.b.).<p> The smallest screen size (2.4 mm) resulted in the highest unit density (1010 kg/m3) and the highest durability (88%) in the pellets produced by the single-pelleting equipment. The change in length of pellets produced by the pilot-scale mill increased as canola meal increased from 18 to 24% at the highest moisture content (%). The pellets were more stable at the highest moisture content when the lowest canola meal used. The addition of 18% canola meal and grinds from a screen size of 6.4 mm produced the highest unit density in the pellets at all moisture levels. The highest bulk density (682 kg/m3) was obtained from shive mixtures with 18% canola meal and a moisture content of 8%. The highest hardness and durability were found for the shive pellets that were produced with 18% canola meal at a moisture content of 14% (w.b). Pellets that were produced at a moisture content of 14% (w.b) resulted in the lowest percentage of moisture absorption. The inclusion of the canola meal in the shive mixture resulted in an increase in the combustion energy of the pellets because of the fat content in the binder. The two levels of canola meal for shive pellets had essentially the same level of emissions. However, there were significant differences between shive pellets and commercial wood pellets in the level of the emissions. Lower amounts of methane (1.29 ppm) and oxygen (164.3 ppt) were found for flax shive pellets than of methane (1.63 ppm) and oxygen (176.6 ppt) in commercial wood pellets.<p> In short, pelleting of flax shives into fuel pellets improved the handling characteristics, increased bulk density and energy content. Fuel pellets made from flax shives had less emission of methane and oxygen from combustion when compared to commercial wood pellets.

This thesis deals with industrial hemp and its use in vertical and horizontal structures. The work is mainly focused on the fillers of industrial hemp and inorganic binder. In the practical part of the feasibility study for future use of industrial hemp in the construction industry as a filling materiál in vertical and horizontal structures. This area has been targeted by all test samples. They are presented here and evaluated and compared the results of tests on unconfined compressive strength, compressive strength, depending on the deformation density of fresh and hardened mixture and the termal conductivity of different types of inorganic binders and fillers such as hemp.

Le travail développé dans cette thèse a pour but d’étudier le comportement hygrothermique de matériaux isolants bio-sourcés, et plus particulièrement les fibres de bois, le béton de chanvre, la laine de lin, la laine de mouton, le métisse® et les anas de lin. Ces matériaux, par essence naturels, présentent des spécificités liées à leur origine (animale ou végétale) et à leur structure (fibres, paille, matrice solide…). Leur porosité, très élevée, les rend réactifs aux variations d’humidité relative ambiante, ce qui peut impacter leurs performances thermiques et leur durabilité (comme pour tous les matériaux), mais également leur conférer des capacités de régulation. Dans un souci d’améliorer la connaissance de ces matériaux particuliers, nous proposons tout d’abord d’étudier l’impact causé par l’humidité sur leurs caractéristiques thermiques, principalement la conductivité thermique et la chaleur spécifique. Ensuite les caractéristiques hygrothermiques sont étudiées, ce qui permet de mieux comprendre les phénomènes dépendant des capacités d’adsorption, de désorption, de perméabilité ou de résistance à la vapeur d’eau. On se rend compte également de l’importance du gradient de température sur l’évolution des transferts hygriques au sein des matériaux. En plaçant les isolants bio-sourcés sous sollicitations aléatoires ou en conditions réelles d’utilisation, nous pouvons suivre leur comportement d’un point de vue expérimental. Le couplage à une approche numérique permet d’identifier les paramètres d’influence prépondérants, dans l’optique de la prédiction des transferts couplés chaleur/masse par une simulation dans des conditions particulières d’utilisation, comme la rénovation d’un habitat existant. On constate à partir de mesures in situ que ces matériaux ont une grande capacité d’adaptation à des environnements dont l’humidité relative est évolutive. / The work developed in this thesis aims to study the hygrothermal behavior of bio-sourced insulating materials, and more particularly wood fibers, hemp concrete, linen wool, sheep wool, material made of textile recycling (metisse®) and flax shives. These materials, which are essentially natural, have specific characteristics linked to their origin (animal or vegetable) and their structure (fibers, straw, solid matrix, etc.). Their very high porosity makes them reactive to the relative humidity variations, which can affect their thermal performances and their durability (as for all materials), but also give them a regulation capacities. In order to improve the knowledge of these particular materials, first, we propose to study the impact caused by moisture on their thermal characteristics, mainly thermal conductivity and specific heat. Then the hygrothermal characteristics are studied, which makes it possible to better understand the phenomena depending on the capacities of adsorption, desorption, permeability or water vapor resistance. Also, we realize the importance of the temperature gradient impact on the evolution of the hygroscopic transfers within the materials. By placing the studied bio-sourced insulation materials under random loading or under real conditions, it will be possible to follow their hygrothermal behavior from an experimental point of view. The numerical approach makes it possible to identify the preponderant influence parameters, in the context of the prediction of coupled heat and mass transfers by simulation under particular conditions of use, such as the renovation of an existing habitat. On the basis of in situ measurements, it can be seen that these materials have a high adaptability to environments whose relative humidity is evolutionary.