<p>Godkänd; 1997; 20070418 (ysko)</p>

Godkänd; 1995; 20080330 (ysko)

No description available.

No description available.

Plans to shut down nuclear power plants in some European countries as well as increased electricity production by wind and solar power will increase the work load on hydroelectric power plants in the future. Also, due to the power grid regulations, hydroelectric power plants undergo more frequent start-ups and shut-downs. During such transient periods, a large amplitude shaft motion can occur, especially in the power plants with vertical shafts. Large shaft motion is not desirable because it can lead to a machine failure. Furthermore, performance limitations of conventional white metal or babbitted bearings call for the development of new bearing designs. An outstanding tribological performance can be achieved by introducing compliant polymer liners. At the same time, bearings with compliant liners may alter rotor-bearing system dynamic behaviour compared to the systems with conventional white metal bearings. The research approach of this thesis is to employ nonlinear analysis to provide further understanding of the compliant bearing dynamic response to synchronous shaft excitation. Plain cylindrical journal bearings with different compliant liner thicknesses were analysed using a nonlinear approach. The numerical model was verified with an in-house developed code at steady state conditions. Results obtained by the numerical models showed good agreement. After verification of the numerical model for fixed geometry journal bearings, models for tilting pad journal bearings were developed. Results for the tilting pad journal bearing with three pads with line pivot geometry were compared with published data in dynamic conditions. A good agreement was obtained between the two numerical models. The effect of pad pivot geometry on bearing dynamic response was investigated. Vertical and horizontal shaft configurations were compared in terms of the effect of preload factor, pivot offset, tapers and pad inclination angles. Influence of the viscoelastic properties of compliant liners was also studied. All these factors significantly affect bearing dynamic response. It is shown how these factors should be selected to control the journal orbit sizes. It was also shown that the compliant liner provides lower maximum oil film pressure and thicker minimum oil film thickness in the bearing mid-plane in both static and dynamic operating conditions. / <p>QC 20120319</p> / Swedish Hydropower Centre

The gears in a transmission are lubricated to prevent their premature failure as a result of pitting and wear on the tooth surfaces. Furthermore, the lubricant also limits the rise in surface temperature of the gears, which could otherwise lead to failure as a result of scuffing. The purpose of this thesis was to construct a fairly realistic theoretical lubrication model for spur and helical gears, the primary output parameters of this model being film thickness and flash temperatures, which would help in the identification of areas on the gear tooth surface prone to the aforementioned modes of failure. This thesis was carried out at the Gear Technology group in Scania CV AB in collaboration with the department of machine design at KTH. Gear lubrication is tricky as it entails the determination of parameters such as loads, curvatures, and velocities; which are different along the entire surface of the gear tooth. Primarily the loads are hard to obtain as they are dynamic in nature; the load is shared between different pairs of teeth during motion. The calculation of velocities and curvatures in an area of the gear surface called the tip relief can also not be done in a straightforward manner. These issues were simplified to a large extent with the assistance of a program called Helical 3D; owing to its powerful contact analysis algorithm, values of the film thickness and flash temperatures could be determined in almost every region where contact occurred between the gear teeth. The results of the lubrication model showed a reduction in film thickness in the tip relief area of the gear tooth surface; which meant that there were higher chances for the incidence of pitting and wear in this region. This was later confirmed when photographs from experimental tests illustrated a pitting line in the tip relief region of the helical gear. It was also inferred from the model that the occurrence of pitting could be greatly reduced if a quadratic tip relief modification were applied when compared to the existing linear modification used at Scania. Another important conclusion drawn was that thermal effects contributed to a significant decrease in the film thickness. Furthermore, the model showed higher flash temperatures close to the tip of the gear tooth surface, and photographs from experiments conducted showed the prescence of scuffing marks there.

No description available.

Bearbetningsprocesser är en viktig del av tillverkningsindustrin. Dessa företag måste kontinuerligt förbättra sina processer och göra dem mer effektiva, minska de ekologiska fotavtrycken och driftskostnaderna. Syftet med denna rapport är att förbättra en rund brotschningsprocess för ett bilföretag. Brotschverktyget är tillverkat av solid HSS och belagt med TiN, som dras genom ett hål i arbetsstycket. På grund av att flera skärkanter fungerar samtidigt är skärkraften hög. Med skärverktygets lågavlastningsvinkel spelar smörjmedlet en kritisk roll i brotschningsprocessen. Arbetet studerar olika skärvätskor i ett laboratorium, genom att simulera påverkan av skärvätskor i en brotschningsprocess med tappningsoperationer under liknande förhållanden. Momentvärdena och beteendet av processen har studerats för de olika smörjmedlen. Studien visade att smörjmedlet har en stor påverkan på vridmoment och spånbildningen. Relationen mellan smörjviskositet och smörjningsförmåga studerades. Dessutom undersöktes sambandet mellan spånbildning och vridmomentbeteende, vilket visar vikten av spånens utrymningskapacitet. Processen har utförts genom att använda olika typer smörjmedel för att undersöka deras påverkan på skärkrafterna och hur de utvecklades under hela processen. Resultaten och den efterföljande analysen har visat att viskositeten har stort inflytande i processen. Viskositeten är omvänt proportionell mot vätskans kapacitet för att komma åt vissa kritiska områden, vilket ökar friktionskrafterna och genereringen av långa spån. Både spånstorleken och smörjmedlets förmåga att utrymma har starka influenser på processen. / Machining processes are an important part of the manufacturing industry. Companies within the manufacturing industry are required to continuously improve their processes and make them more efficient, to reduce the ecological impact and operational costs. The aim of this thesis is to be able to improve a circular broaching process for an automotive company. The broaching tool is made from solid High-Speed Steel and TiN coated, which is pulled through a hole in the workpiece. Due to multiple cutting edges acting simultaneously, the cutting force is high. With a low relief angle of the cutting tool and low cutting speed, the lubricant plays a critical role in the broaching process. The thesis studies different cutting fluids in a laboratory, by simulating the impact of cutting fluids in a broaching process with tapping operations under similar conditions. The torques values and the behaviour of it during the process have been recorded for different lubricants. The lubricants were found to have a strong influence in the torque required and the chip formation. The relation between lubricant viscosity and lubrication performance was studied. In addition, the relation between chip formation and torque behaviour was explored, showing the importance of chip evacuation capacity. The process has been carried out by using different lubricants to examine the required cutting forces and how they evolved throughout the process. The results and the consecutive analysis have shown an influence of the viscosity in the process. The viscosity is inversely proportional to the capacity of the fluid to access certain critical areas, increasing the friction forces and the generation of long chips. Both the chip size and the ability of the lubricant to evacuate have strong influences on the process.

No description available.

A common approach in numerical studies of elastohydrodynamic lubrication (EHL) is based on solving the Reynolds equation that governs pressure distribution in thin lubricant films. The Reynolds equation is derived from the Navier-Stokes equations by taking assumptions that are considered valid when the thickness of the lubricant film is much smaller than its length. A massive increase in the computing power over the last decades has enabled the use of CFD (computational fluid dynamics) approach, based on the Navier-Stokes equations, in solving the EHL problem. Comparisons between the CFD and Reynolds approach have generally shown very good agreement. Differences can occur when the thin film assumptions of the Reynolds equation are not applicable. In this study, a CFD approach has been chosen with the aim of investigating effects of asperities and rheology at high loads on the behavior of the thin EHL films. A high quality mesh was generated in ANSYS ICEM CFD, while ANSYS Fluent has been employed in solving the Navier-Stokes equation by finite volume method (FVM). For EHL modeling, a set of user-defined functions (UDFs) were used for computing density, viscosity, wall temperature, heat source and elastic deformation of one of the contacting surfaces. Two lubricants were used, a commonly used oil in CFD analyses of EHL and Squalane. Non-Newtonian fluid behavior and thermal effects were considered. For Squalane, the two rheology models, Ree-Eyring and Carreau were compared. Squalane has been chosen in this study since it is one of the rare fluids with known parameters for both rheology models. Finally, the influence of surface roughness was explored for the cases of a single asperity and a completely rough wall. A surface roughness profile is generated in MATLAB by using the Pearson distribution function. In the cases where the surfaces are assumed to be completely smooth, the obtained results at the pressure of about 0.5 GPa closely correspond to literature, both in the case of Newtonian and non-Newtonian fluid behavior. At the pressure of about 1 GPa, severe shearing of the lubricant film has been noticed, characterized by a pronounced shear-band and plug flow. It was found that the choice of viscosity and rheology models has a large influence on the obtained results, especially at the high pressure levels. Finally, it was discovered that the developed CFD model of EHL has a great potential in studying the effects of surface roughness on the lubricant film behavior.