No description available.

Trends in the construction of deep excavations include deeper excavations situated closer to buildings. This research provides insight into mechanisms of soil-structure interaction for piled buildings adjacent to deep excavations to be used in the design and monitoring of deep excavations in urban areas. Most methods to assess building response have originally been developed for tunnelling projects or buildings with shallow foundations. Monitoring data of the construction of three deep excavations for the North South metro Line in Amsterdam, The Netherlands have been used to validate these methods specifically for piled buildings. In all three of the Amsterdam deep excavations studied, the largest impact on the ground surface and buildings is attributed to preliminary activities instead of the commonly expected excavation stage. The in situ preliminary activities caused 55-75% of the surface settlement and 55-65% of the building settlements. Surface settlements measured behind the wall were much larger than the wall deflections and reached over a distance of 2-3 times the excavated depth away from the wall. The shape of the surface settlements found resembles the hogging shape as defined by Peck (1969). For the excavation stage only, the shape of the displacement fits the profile proposed by Hsieh and Ou (1998). Most prediction methods overestimate the soil displacement at depth. An analytical method has been established and tested for the behaviour of piled buildings near excavations. This method includes the reduction of pile capacity due to lower stress levels, settlement due to soil deformations below the base of the pile and development of negative (or positive) skin friction due to relative movements of the soil and the pile shaft. The response of piles in the case of soil displacements depends on the working load of the pile, the percentages of end bearing and shaft friction of the pile, the size and shape of the soil settlements with depth and the distribution of the maximum shaft friction with depth. A method is derived to determine the level for each pile at which the pile and soil settlement are equal. Buildings in Amsterdam built before 1900 and without basement are most sensitive to soil displacements. For all other buildings, the pile settlement depends mainly on the working load. The actual damage experienced in buildings depends also on the relative stiffness of the building compared to the soil. Cross sections in Amsterdam have been evaluated and it is concluded that the Goh and Mair (2011) method provides a realistic, although rather large range of possible modification factors for the deflection of buildings next to excavations, deforming in hogging shape. For the incidents that happened at Vijzelgracht some well known damage indicators have been evaluated.

<p>  </p> <p>Knowledge of the displacement and deformation fields beneath foundation elements obtained from carefully executed experiments is required to validate state-of-the-art numerical simulations, which in turn enable the development of better foundation design methods. This dissertation presents the results of an experimental program in which load tests were performed on model footings in a half-cylindrical calibration chamber with a transparent viewing window across its diameter. The digital image correlation (DIC) method was used to obtain the strain and displacement fields in the soil from digital images taken during the tests. Tests performed on both smooth and rough footings show a significant dependence of resistance on footing base roughness, with the DIC results providing insight into the reasons for that dependence. The experimental bearing capacity results are used to validate a previously proposed method in which an equivalent friction angle is used for calculation of the bearing capacity of footings in sand.</p> <p>Schmertmann's method is one of the traditional methods for estimating the settlement of axially loaded footings in sand using cone penetration test (CPT) data. The method was developed for footings placed on the surface of a single, uniform sand layer; it assumes a depth of influence below the footing base within which most of the soil deformations take place and an influence diagram to quantify the influence factor as a function of depth. However, the literature contains limited information on the strain influence diagrams for footings on layered sands, and, as a result, there is no way to accurately account for the effect of sand layering on footing settlement. In this study, Schmertmann's approach for calculating the strain influence factor is modified to account for the effect of two sand layers with varying thickness and relative density. Penetration experiments were performed using a half-square model footing (width <em>B</em> = 90 mm) placed on the surface of both single and two-layered (dense over medium-dense and medium-dense over dense), air-pluviated, silica sand samples prepared inside a half-cylindrical calibration chamber designed for digital image correlation (DIC) analysis. The test results indicate that both the thickness and relative density of the top sand layer (the layer in contact with the footing base) affect the parameters of the strain influence diagram. For dense sand over medium-dense sand, the depth to the peak strain influence factor varies with the thickness of the dense layer; however, when the thickness of the dense layer is 1.5<em>B</em> or greater, the strain influence diagram is similar to that obtained for a single, uniform sand layer. In contrast, for medium-dense sand over dense sand, the peak value of the strain influence factor varies with the thickness of the medium-dense layer up to a value of 1<em>B</em>. Based on the results obtained in this study, new strain influence diagrams are proposed for settlement calculation of square footings on two-layered sand profiles. The proposed method for estimation of footing settlement in layered sand is validated against measured data obtained from a full-scale, instrumented footing load test reported in the literature. </p> <p>The expressions for the shape and depth factors available in the literature for bearing capacity calculation are mostly empirical and are based on results obtained using limit analysis or the method of characteristics assuming a soil that is perfectly plastic following an associated flow rule. This study presents the results of an experimental program in which load tests were performed on model strip and square footings in silica sand prepared inside a half-cylindrical calibration chamber with a transparent visualization window. The results obtained from the model footing load tests show a significant dependence of footing penetration resistance on embedment depth. The load test results were subsequently used to determine experimentally the shape and depth factors for model strip and square footings in sand. To obtain the displacement and strain fields in the sand domain, the digital image correlation (DIC) technique was used to analyze the digital images collected at different stages during loading of the model footing. The DIC results provide insights into the magnitude and extent of the vertical and horizontal displacement and maximum shear strain contours below and around the footing base during penetration.</p> <p>The loading of a footing in sand generates substantial shear bands as a mechanism for failure develops with the formation of slip surfaces. The interaction of sand particles in the shear band governs its constitutive response to loading. This study provides the results of loading experiments performed under different conditions on half-square model footings (width <em>B</em> = 90 mm) in dense air-pluviated silica sand samples prepared in a half-cylindrical calibration chamber equipped with an observation window that allows collection of images of the sand domain during testing. Two sands (Ottawa sand and Ohio Gold Frac sand) with different roundness (angularity) were used to perform these experiments. The digital image correlation (DIC) technique was used to obtain the incremental strain fields in the sand domain. The zero-extension line (ZEL) concept was then used to study the shear strain localization process and to obtain the orientation of the shear bands from analysis of the incremental strain fields. The results show that sand particle morphology, footing surface roughness, load eccentricity, and depth of embedment of the model footing have an impact on the dominant shear band patterns that develop below the model footings, and, as a result, all of these factors affect the unit bearing capacity of footings. The estimated thickness <em>t</em>s of the shear band from the experiments is approximately 6<em>D</em>50 for Ottawa sand and approximately 8<em>D</em>50 for Ohio Gold Frac sand. </p>