The literature on isolated bursts and possible mechanisms of origin has been critically reviewed, and observations point to a mechanism involving omission of electromagnetc radiation from plasma oscillations in the solar corona excited by outward travelling disturbances. Solar noise observations on 125 Mc./s. recorded at Rhodes University during the period November 26 1957 - February 6 1958 have been analysed by the author for isolated bursts, and these observations show the same general features reported by previous investigators. In interpretation of these records particular attention has been devoted to two aspects of isolated bursts; namely the preponderance on single frequency records of double-humped bursts, and the shape of isolated burst profiles. The authors suggests that a probable explanation of double-humped bursts observed on any frequency f is that the first hump represents omission at or near the level of zero refractive index for f radiation, and that the second hump corresponds to harmonic omission at the f/2 level. Source velocities may be calculated from the time delay between the peaks and an average value of 2 x 10⁴ km./sec. was obtained from an analysis of 21 double-humped bursts. This value is in very good agreement with that deduced by Wild (1950b) from the rate of frequency drift of peak intensity of isolated bursts. Simple isolated bursts had decay profiles which are approximatley exponential in shape, and this is usually interpreted in terms of the natural decay of plasma oscillations in the medium of origin. The author has verified that the exponential function is a good fit to the observed decay profiles, but shows that a relation of the form I - ¹/n (superscript) ⋉ t (where I is intensity and t is time) fits just as well. An alternative model is suggested which would lead to an exponential-like decay profile which is not determined by the natural decay of plasma oscillations. The work concludes with some suggestions for further research.

No description available.

No description available.

With the rapid increase in energy demand and the rise of CO2 levels due to traditional energy production from fossil fuels, it is critical to the transition to a sustainable and renewable energy sources. Recently, photovoltaic technology has been raised as a promising alternative to fossil fuel energy production. Solar cells, predominately crystalline silicon technology, are currently 3.6% of electricity production. To maintain this progress, coupling the perovskite and silicon in tandem devices has enormous potential to increase the efficiency of solar energy production, where perovskite solar cells emerged as a promising technology. Textured silicon solar cells are a well-established technology; keeping the advantage of this technology, it is crucial to employ the perovskite to be a compatible top cell for silicon-based tandems. Here, we optimize the silicon bottom cell by understanding the influence of temperature, time, and etchant concentration on the optical properties and performance of the device. Then, we investigate the impact of the textured silicon on the optoelectronic properties of perovskite. Using hyperspectral imaging, we demonstrate that different texturing substrates influence the PL of perovskite, which is associated with the thickness of the perovskite. Lastly, we explored the delamination of the devices due to the weak adhesion between C60/SnO2 after the deposition of IZO and MgF2, which was found to be caused by the deposition conditions. The high temperature and power density caused a weak adhesion between C60/SnO2. Overall, these findings will help to alter the design of Perovskite/Silicon tandem devices to accelerate the commercialization of tandem technology.

Two types of solar collecting systems are frequently employed--flat plate collectors with spectrally selective windows which trap sunlight with the "greenhouse effect" and focusing systems with curved mirrors which concentrate the sun's rays on an absorbing surface. The flat plate collector is the simpler of the two designs, but cannot readily provide temperatures as high as the focusing collector. Both of the collectors are candidates for absorption cycle solar air conditioning systems. This role dictates higher temperature than are normally required of solar collectors, particularly the flat plate design. Focusing systems of interest here are those which are fixed in orientation and require no elaborate solar tracking mount. Such collectors might be economically competitive with flat plate configurations if the higher energy "quality" or delivery temperature they can provide permitted a smaller installation than would be possible with a flat plate collector. An analysis of the two collector candidates is undertaken here to assess the merits of a fixed orientation focusing collector and a more traditional flat plate system. This analysis indicates that the focusing design is superior to the flat plate for solar air conditioning. The study of the two designs includes selection of system configurations and the development of their mathematical descriptions. The analytical approach was to incorporate mathematical models of the collectors into a computer program which predicts the performance of both the flat plate and focusing systems. The program has been designed to permit convenient variation of important parameters so that their effect on collector performance may be determined. The results of the collector analysis and the computer program are presented with sufficient information to permit the reader to use the program for his own analyses.

Gas, electricity, heating and cooling buildings - comfort — our lives revolve around fossil fuels. Technology and the demands of living in today's society add to our gigantic fossil fuel appetite. With gas prices topping three dollars per gallon, changes must be made. This thesis project presents an analysis of passive solar landscape design (PSLD) principles used to create microclimates within the landscape, and thereby increasing human comfort both indoors and outdoors. The analysis includes case study results of fossil fuel consumption and PSLD implementation. Microclimatic comfort is revealed in the design of a solar park in historic Smithfield, Virginia. Smithfield Solar Park is designed with PSLD principles to be self-sustaining - the Farmer's Market pavilions and educational center generating their own electricity through a solar voltaic system. This system is enhanced by careful siting and selection of trees, shrubs and built structures and use of local materials to reduce transportation distances. Smithfield Solar Park features a Farmer's Market, outdoor movies and Friday Cheers, and will host regional and local festivals and events, enhancing tourism and the economy of Smithfield's Historic District. Landscape architecture stands in prime position to improve landscapes and lessen both our dependency on and consumption of fossil fuels through implementation of PSLD principles. Public education about the benefits of implementing PSLD principles can have local, regional, national and global effects on our fuel consumption. / Master of Landscape Architecture

[ES] El objetivo principal de esta tesis es contribuir al avance de nuevas técnicas de elaboración con bajo coste, utilizando materiales tipo de cobre, indio, galio y selenio CIGS y Perovskita para aplicaciones en energía solar fotovoltaica. CIGS parecen ser adecuadas ya que son de bajo costo de producción y se han reportado eficiencias de conversión del 23,35%. Por otro lado, las perovskitas híbridas de haluros de plomo orgánicos-inorgánicos han aparecido como nuevos materiales excepcionales para celdas solares, especialmente porque la eficiencia de las celdas solares basadas en perovskita ha aumentado del 3.8% al 22.7% en menos de un lustro. Este trabajo se ha dedicado a experimentar sobre la elaboración y caracterización de CIGS y los perovskitas de metilamonio de yoduro de plomo de (MAPbI3) y formamidinio de yoduro de plomo (FAPbI3), que se utilizo tanto en la aplicación a las células solares de perovskitas y en las células Tándem CIGS-perovskita. Las películas se caracterizaron por difracción de rayos X, espectroscopía Raman, microscopía electrónica de barrido, análisis de espectroscopía de energía dispersiva, microscopía de fuerza atómica, transmisión electrónica microscopía, fotoluminiscencia y espectroscopia UV-Vis. En las capas de CIGS depositadas por electrodeposición se investigó el efecto de diferentes parámetros, También investigamos en detalle el efecto del contacto posterior en las propiedades estructurales y ópticas de CIGS. Constatamos que el tipo de contacto posterior tiene un efecto significativo en el rendimiento posterior de las películas delgadas CIGS. Además, estudiamos la técnica de espray pirólisis para producir películas CIGS. Se estudió el proceso de recocido, que es el factor clave para mejorar el rendimiento de las células solares. Se elaboraron diferentes películas delgadas constituidas de nuestro dispositivo CdZnS/CdS/CIGS/Mo eso utilizó una capa conductora transparente de CdZnS para minimizar la alineación de la interfaz. Por otro lado, se analizó el proceso de cristalización y la estabilidad de las capas MAPbI3. Las capas de MAPbI3 se trataron añadiendo antisolvente a diferentes velocidades. Durante el tratamiento se producen intercambios complejos que influencian muchas propiedades fisicoquímicas. Se investigaron las propiedades ópticas y eléctricas de las películas de MAPbI3. Para mejorar la estabilidad de MAPbI3, se incorporó tetrabutilamonio (TBA), observando una mejora en la formación de la estructura perovskita que crece en la dirección preferente (110). La fase cristalina de MAPbI3 dopada con TBA presenta mejor cristalinidad, gran tamaño de grano, morfología superficial sin poros lo que es adecuado para la fabricación de dispositivos optoelectrónicas con mayor rendimiento. Además, hemos identificado el impacto de TBA en las propiedades foto físicas de MAPbI3. En las muestras de TBA:MAPbI3 aumenta la intensidad de la fotoluminiscencia al reducir la densidad de los estados de trampa y la absorción óptica muestra un cambio significativo hacia longitudes de onda más largas y la banda prohibida óptica varió de 1.8 a 1.52 eV. Finalmente, las muestras dopadas con 5% TBA mejoraron su estabilidad y se encontró que después de 15 días la estabilidad permanecía excelente en una humedad de ~ 60%. Por otra parte, investigamos el efecto de guanidinio (GA) sobre las propiedades estructurales y ópticas de FAPbI3. La relación entre la fase a de perovskita deseable y la fase indeseable y se ha estudiado en función del contenido de GA. Se comprobó que el dopaje con GA es eficaz en el control de la relación de fases a/y y luego en la estabilización de la fase a. Los resultados muestran que añadiendo una cantidad adecuada del 10% GA conduce a una mejora de película de perovskita que se evidencia en la homogeneidad de la fase a estable, granos de mayor tamaño y capas libres de poros. Además, 10% GA:FaPbI3 demostraron una excelente estabilidad después de ser envejecidas durante 15 días en un ambiente con humedad relativa del 60%. / [EN] The thesis work presented is part of the work in the Laboratory of New Materials for Photovoltaic Energy in the main target to use low cost techniques for elaboration of Perovskite and Copper, indium, gallium, and selenium CIGS materials for photovoltaic application. Organic-inorganic lead halides perovskites have currently and exceptionally appeared as new materials for low cost thin film solar cells specially that the efficiency of perovskite based solar cell have jumped from 3.8% to 22.7% in short time.in other hand, CIGS solar cells record 23.35% efficiency and still can be boosted. Here, we report the elaboration and characterization of CIGS as well as methylammonium lead iodide perovskites MAPbI3 and formamidinuim iodide lead iodide perovskites FAPbI3 absorbers for perovskite-based solar cells and Tandem Perovskites/ CIGS. The thin films prepared were characterized by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis, atomic force microscopy (AFM), transmission electron microscopy (TEM), Photoluminescence analysis (PL) and UV-Vis spectroscopy. The first stage was devoted for the effect of different parameters on the growth of CIGS by electrodeposition and we investigate the impact of different back contact in structural and optical proprieties. In a second stage, we report the growth of CIGS films by spray pyrolysis, we studied the effect of experimental parameter also the annealing process which is the key factor for improving the performance of solar cells,subsequently we elaborated different films constituted CdZnS/CdS/CIGS/Mo solar cells, the approach is to change the toxic ZnO by using a transparent, conductive CdZnS layer. In other hand, MAPbI3 film was investigated in order to optimize the chemical composition and to study the crystallization process also to get sight about the stability of perovskite materials to meet the requirement of their application as an active layer in perovskite solar cell. For this purpose. the MAPbI3 film surface was treated by adding diethyl ether antisolvent with different rates. during the treatment complex exchanges are appearing at the same time under the influence of quite a lot of physicochemical properties. A whole understanding of this topic is critically important for improving solar cell performance. MAPbI3 doped by the tetrabutylammonium TBA is boosting the formation of perovskite structure, leading to a higher orientation along the (110) and shows better crystallinity, large grain size, pinhole-free, which is suitable for the manufacturing of the optoelectronic devices with higher performance. Also, we have identified the impact of TBA in the photo-physical properties, we have noticed that the TBA improve the photoluminescence emission by reducing the density of trap states and the optical absorption indicates a significant shift to the lower wavelength and optical bandgap varied from 1.8 to 1.52 eV. Finally, the stability was explored for 5% TBA, it found that after 15 days the stability remained excellent in relative humidity of ~60%. These results would be helpful for realizing stable and high performance MAPbI3-based devices. Furthermore, we inspect the effect of monovalent cation substitution of Guanidinium (GA) on the structural and optical properties of FAPbI3 thin films perovskites. The ratio between the desirable a-phase and the undesirable y yellow phase is studied as a function of GA content. GA doping is shown to be efficient in the control of a/y phases ratio and then in the stabilization of the a-FaPbI3 phase. We qualitatively evaluate the impact of 10% of guanidinium on the phase composition and microstructure of films. The results show that an adequate amount of 10% GA:FaPbI3 leads to a homogeneous perovskite film with stable a phase, large grains, and free pinholes. 10% GA: FaPbI3 films demonstrate excellent stability after aging for 15 days in relative humidity of~60%. / [CA] L'objectiu principal d'aquesta tesi és contribuir a l'avanç de noves tècniques d'elaboració de baix cost, fent servir materials d'aliatges del tipus de coure, indi, gal·li i seleni (CIGS) i perovskites, per a aplicacions en energia solar fotovoltaica. El CIGS sembla ser adequat ja que són de baix cost de producció i s'han reportat eficiències de conversió del 23,35%. D'altra banda, les perovskites híbrides d'halurs de plom orgànics-inorgànics han aparegut com a nous materials excepcionals per cel·les solars, especialment perquè l'eficiència de les cel·les solars basades en perovskites ha augmentat del 3.8% al 22.7% en menys d'un lustre. En el present treball, reportem l'elaboració i caracterització de CIGS y de perovskitas de iodur de plom de metilamoni (MAPbI3) i de iodur de plom de formamidini (FaPbI3) per a les cèl·lules solars de CIGS i tàndem Perovskites/CIGS. En les capes de CIGS dipositades per electrodeposició es va investigar l'efecte dels diferents paràmetres sobre el procés d'electrodeposició, així com l'efecte del contacte posterior sobre les propietats estructurals i òptiques del CIGS. Ens trobem que el tipus de contacte posterior té un efecte significatiu en la posterior interpretació de pel·lícules primes CIGS. A més, vam estudiar la tècnica de polvorització de la piròlisi per produir pel·lícules de CIGS. Es va estudiar el procés de recuit, que és el factor clau per millorar el rendiment de les cèl·lules solars. Es van produir diferents pel·lícules fines formades pel nostre dispositiu CdZnS/CdS/CIGS/Mo que utilitzaven una capa conductiva CdZnS transparent per minimitzar l'alineació de la interfície. D'altra banda, es van investigar perovskites MAPbI3, amb la finalitat d'optimitzar la composició química i estudiar el procés de cristal·lització també per a conèixer l'estabilitat dels materials de perovskita. la cristal·lització s'aconsegueix alentint la solubilitat en una solució saturada mitjançant l'addició d'una quantitat diferent de l'antisolvent d'èter dietílic. Durant el tractament apareixen al mateix temps intercanvis complexos sota la influència de moltes propietats fisicoquímiques. Una comprensió completa d'aquest tema és de vital importància per a millorar el rendiment. Amb l'objectiu principal d'augmentar l'estabilitat de MAPbI3, el tetrabutilamoni (TBA) es pot incorporar a MAPbI3, impulsant la formació de l'estructura de perovskita, la qual cosa porta a una major orientació al llarg de (110). MAPbI3 dopades amb TBA presenten una millora de la cristalinitat, major grandària, la qual cosa és adequada per a la fabricació de dispositius optoelectròniques de major rendiment. A més, hem identificat l'impacte de TBA en les propietats foto físiques de MAPbI3. Hem notat que el dopatge amb TBA millora tant l'emissió de la fotoluminiscència en reduir la densitat dels estats de trampes com l'absorció òptica on apareix un canvi significatiu de la banda òptica prohibida cap a longituds d'ona més llargues que significa disminuir l'energia del gap, que va variar de 1.8 a 1.52 eV. Finalment, es va explorar l'estabilitat per les perovsquites dopades amb 5%TBA. Es va trobar que després de 15 dies l'estabilitat romania excel·lent en un humitat de 60%. A més, hem estudiat FAPbI3 com un dels materials de perovskita més atractius. Hem investigat l'efecte de la substitució de guanidini (GA) sobre les propietats estructurals i òptiques de FAPbI3. La relació entre la fase a de perovskita desitjable i la fase indesitjable y es va estudiar en funció del contingut de GA. Es mostra que el dopatge amb GA és eficaç en el control de la relació de fases a /y i després en l'estabilització de la fase a-FaPbI3. Els resultats mostren que una quantitat adequada de 10% GA condueix a una pel·lícula homogènia amb fase a estable, grans grans lliures de porus i forats. Les pel·lícules de 10% GA:FaPbI3 demostraren una excel·lent estabilitat després de l'envelliment durant 15 dies en un ambient humit (humitat relativa de 60%). / Bouich, A. (2020). Study and Characterization of Hybrid Perovskites and Copper-Indium-Gallium Selenide thin films for Tandem Solar Cells [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/160621

The central idea of the 2005 Virginia Tech Solar House was to celebrate its solar aspects while integrating the engineering systems and the architecture into a single entity. Through the process of design and construction, the relationship between each detail and the overall architectural concept became evident. Highlighting four specific details to illustrate such intimate relationship, this study shows the importance of carefully working through each detail to remain faithful to the original design without any major compromise. / Master of Architecture

Digitized by Kansas Correctional Industries

An original low cost modular system which collects excess solar energy entering a conventional cold greenhouse during the day and uses the stored energy at night for heating has been devised and analysed. During the day, fluid absorbs heat as it is pumped through semi-transparent panels mounted immediately inside the greenhouse roof and then returned to an insulated tank forming the thermal store. At night the warm fluid is recirculated through the panels and/or emitters near the plants to provide greenhouse heating. Semi-transparent panels were designed and constructed and their thermal operation analysed in a test rig. Semi-transparent panels not only collect energy from the sun but also, unlike conventional solar collectors, gain up to 70% of heat from adjacent warm air. A semi-empirical mathematical model of the thermal. operation of the panels is presented which predicts panel energy gain with better than 20% accuracy. A prototype system of panels and store was constructed in a small greenhouse which had been partitioned into test and control compartments. Experiments were conducted into the operation of. the system and its effect on the vertical temperature profile and illumination inside the greenhouse both with and without plants. At night, the panels heated plants mainly by restricting radiative losses to the sky, so that leaf temperatures were elevated by up to 2.5 deg. C. Panels reduced light levels to about 65% of those in the control compartment. A detailed computer model was written to predict the illumination and temperatures inside a greenhouse fitted with a panel/store system. This model was validated and can therefore be used for the general analysis of semi-transparent solar panel systems and their effect in greenhouses. Panel/store systems were calculated to supply, for heating at night, about 6% of the annual solar energy incident on the greenhouse.