Global ETD Search

1	A comparative study of the seismic base shear force and story drift ratios using Time History and Modal Spectrum Analysis according to Peru Code E.030 and ASCE 7.16 on high-rise buildings Quezada Ramos, Eder Nel, Serrano Arone, Yaneth, Huaco, Guillermo 30 September 2020 (has links) El texto completo de este trabajo no está disponible en el Repositorio Académico UPC por restricciones de la casa editorial donde ha sido publicado. / Since the last decade there is an important increase of high-rise buildings in Peru, especially in urban areas. Therefore, it is necessary to assess if the Peruvian Seismic Code is applicable for this type of buildings which have long natural periods as their main characteristic. The main objective of this article is to compare the results of the base shear and story drift ratios of Peruvian seismic design code E.030 with those of the ASCE 7-16 standard to the case of high-rise buildings, this due to the fact that there is limited information for tall buildings in Peru or comparison between national or international code for this type of structures. These high rise buildings have square and rectangular plan floors. Half of them have moment frames and reinforce concrete slab around the rigid core and the others have post-tensioned slab as their vertical load resisting system and central core walls with peripheral columns as the lateral force resisting system. Hence, the response spectrum analysis (RSA) is carried out for every case of the four tall buildings with different configurations using both seismic codes. Then results are compared with the linear response history analysis (LRHA) considering five Peruvian ground motions records, which were scaled to 0.45g PGA. It was verified that generally both the base shear and the interstory drifts calculated using ASCE7-16 are less than that obtained with the seismic code E.030. High-Rise Buildings Long Natural Period Post-tensioned Slab Rigid Core Seismic Base Shear Force Story Drift Ratios
2	Simple Models For Drift Estimates In Framed Structures During Near-field Earthquakes Erdogan, Burcu 01 September 2007 (has links) (PDF) Maximum interstory drift and the distribution of this drift along the height of the structure are the main causes of structural and nonstructural damage in frame type buildings subjected to earthquake ground motions. Estimation of maximum interstory drift ratio is a good measure of the local response of buildings. Recent earthquakes have revealed the susceptibility of the existing building stock to near-fault ground motions characterized by a large, long-duration velocity pulse. In order to find rational solutions for the destructive effects of near fault ground motions, it is necessary to determine drift demands of buildings. Practical, applicable and accurate methods that define the system behavior by means of some key parameters are needed to assess the building performances quickly instead of detailed modeling and calculations. In this study, simple equations are proposed in order for the determination of the elastic interstory drift demand produced by near fault ground motions on regular and irregular steel frame structures. The proposed equations enable the prediction of maximum elastic ground story drift ratio of shear frames and the maximum elastic ground story drift ratio and maximum elastic interstory drift ratio of steel moment resisting frames. In addition, the effects of beam to column stiffness ratio, soft story factor, stiffness distribution coefficient, beam-to-column capacity ratio, seismic force reduction factor, ratio of pulse period to fundamental period, regular story height and number of stories on elastic and inelastic interstory drift demands are investigated in detail. An equation for the ratio of maximum inelastic interstory drift ratio to maximum elastic interstory drift ratio developed for a representative case is also presented.
3	Quantifying Seismic Design Criteria For Concrete Buildings Tuken, Ahmet 01 May 2003 (has links) (PDF) The amount of total and relative sway of a framed or a composite (frame-shear wall) building is of utmost importance in assessing the seismic resistance of the building. Therefore, the design engineer must calculate the sway profile of the building several times during the design process. However, it is not a simple task to calculate the sway of a three-dimensional structure. Of course, computer programs can do the job, but developing the three-dimensional model becomes necessary, which is obviously tedious and time consuming. An easy to apply analytical method is developed, which enables the determination of sway profiles of framed and composite buildings subject to seismic loading. Various framed and composite three-dimensional buildings subject to lateral seismic loads are solved by SAP2000 and the proposed analytical method. The sway profiles are compared and found to be in very good agreement. In most cases, the amount of error involved is less than 5 %. The analytical method is applied to determine sway magnitudes at any desired elevation of the building, the relative sway between two consecutive floors, the slope at any desired point along the height and the curvature distribution of the building from foundation to roof level. After sway and sway-related properties are known, the requirements of the Turkish Earthquake Code can be evaluated and / or checked. By using the analytical method, the amount of shear walls necessary to satisfy Turkish Earthquake Code requirements are determined. Thus, a vital design question has been answered, which up till present time, could only be met by rough empirical guidelines. A mathematical derivation is presented to satisfy the strength requirement of a three-dimensional composite building subject to seismic loading. Thus, the occurrence of shear failure before moment failure in the building is securely avoided. A design procedure is developed to satisfy the stiffness requirement of composite buildings subject to lateral seismic loading. Some useful tools, such as executable user-friendly programs written by using &ldquo / Borland Delphi&rdquo / , have been developed to make the analysis and design easy for the engineer. A method is also developed to satisfy the ductility requirement of composite buildings subject to lateral seismic loading based on a plastic analysis. The commonly accepted sway ductility of &amp / #956 / &amp / #916 / =5 has been used and successful seismic energy dissipation is thus obtained.
4	A Risk Based Approach to Module Tolerance Specification Shahtaheri, Yasaman 22 April 2014 (has links) This research investigates tolerance strategies for modular systems on a project specific basis. The objective of the proposed research is to form a guideline for optimizing the construction costs/risks with the aim of developing an optimal design of resilient modular systems. The procedures for achieving the research objective included: (a) development of 3D structural analysis models of the modules, (b) strength/stability investigation of the structure, (c) developing the fabrication cost function, (e) checking elastic and inelastic distortion, and (f) constructing the site-fit risk functions. The total site-fit risk function minimizes the cost/risk associated with fabrication, transportation; alignment, rework, and safety, while maximizing stiffness in terms of story drift values for site re-alignment and fitting alternatives. The fabrication cost function was developed by collecting 61 data points for the investigated module chassis using the SAP2000 software while reducing the initial section sizes, in addition to the fabrication costs at each step (61 steps). With the reduction of the structural reinforcement, story drift values increase, therefore there will be a larger distortion in the module. This generic module design procedure models a trade-off between the amount of reinforcement and expected need for significant field alterations. Structural design software packages such as SAP2000, AutoCAD, and Autodesk were used in order to model and test the module chassis. This research hypothesizes that the influential factors in the site-fit risk functions are respectively: fabrication, transportation, alignment, safety, and rework costs/risks. In addition, the site-fit risk function provides a theoretical range of possible solutions for the construction industry. The maximum allowable modular out-of-tolerance value, which requires the minimum amount of cost with respect to the defined function, can be configured using this methodology. This research concludes that over-reinforced or lightly-reinforced designs are not the best solution for mitigating risks, and reducing costs. For this reason the site-fit risk function will provide a range of pareto-optimal building solutions with respect to the fabrication, transportation, safety, alignment, and rework costs/risks. Risk Tolerance Tolerance Specification Risk Based Risk Based Approach Module Modular Module Tolerance Module Tolerance Specification Fabrication Cost Function Risk Function Module Fabrication Module Risk Function Module Fabrication Cost Module Risk Optimal Resilient Design Perato Optimal Boundary Optimal Module Resilient Design SAP2000 Module Transportation Risk Module Alignment Risk Module Safety Risk Module Rework Risk Story Drift Over Reinforcement Lightly Reinforced Lightly Reinforced Module Elastic Inelastic Distortion Stiffness Optimal Modular Resilient Design Over Reinforced Module

1

Page generated in 0.0786 seconds