The automotive manufacturing industry is facing an interesting period of trial when a lot of improvement is expected of them in a short period of time to contribute to a cleaner planet by applying technologies that will reduce fossil fuel consumption. Electrification was good, but this must be accompanied by substantial curb weight reduction, which was provided by alloys such as A365, Aural 5 (AlSi8MnMg), Aural 2 (AlSi10MnMg), and Mercalloy 367 (AlSi9MgMnSr) for making structural parts. The use of these Al alloys is accompanied with extensive heat treatment which on its own involves fossil fuel consumption. In this research, test plates were made utilizing high vacuum high pressure die casting (HVHPDC) and a unique Al-Fe based eutectic alloy with Zn and Mg as precipitation strengtheners. Experimental results demonstrated that they age naturally, with their mechanical properties rising to the industry requirement within three days. DSC experiments carried out at various ages gave further experimental evidence to this natural ageing phenomenon. A portion of the samples was then given an experimental "paint bake" treatment at different ages. This is typical on an assembly line where the coated parts are baked at a temperature range of 120 - 200oC for thirty minutes. It was evidently defensible that samples of various ages respond to the treatment in different ways. The mechanical characteristics of the samples decreased after treatment to same value and progressively increased to match the values of the control samples. During the duration of the experiment, some samples rose quickly while others remained "nearly dead" in the state of low mechanical characteristics or climbed sluggishly to catch up with the natural ageing curve. The poorest results were seen in samples handled at the early stage when the initial clusters are forming indicating that it might not be a good idea to interfere with the NA process at those times. / Thesis / Master of Applied Science (MASc) / Fueled by the desire to produce an Al alloy with good mechanical properties arising from natural ageing, high vacuum high pressure die casting (HVHPDC) was used in making castings of this alloy which contains Fe for improvement on its castability and recyclability, contains Zn and Mg which act as the precipitating strengtheners driving the natural ageing phenomenon. Tests and experiments like uniaxial tensile tests, differential scanning calorimetry and electrical conductivity tests were carried out to ascertain its suitability to be used for structural automotive parts without heat treatment. The results showed that the new Nemalloy HE700 met with the minimum industry requirements for mechanical properties of materials for structural automotive applications within 3 days of natural ageing. The alloy was then subjected to experimental paint bake treatment to observe its reaction to paint bake process and the results were able to show when to do paint bake for best outcome.

High pressure die casting (HPDC) is both a cost-efficient and high throughput method for making near-net shape castings. 7xxx series aluminum alloys are excellent candidates for manufacturing structural components for significant light-weighting opportunities in the automotive industry. This project explores the development of a new 7xxx series aluminum alloy with iron additions to improve castability. The main objective of this project is to develop an optimized heat treatment process for the new Al-Zn-Mg-Fe alloy to achieve solute homogenization in the primary Al grains. The rationale behind adding iron as an alloying element was presented, as well as an analysis of the Al-Fe intermetallic phases to show their mitigating effects on hot tearing. A detailed analysis of the casting quality was carried out, including detailed microstructural analyses of defects and defect-free castings, correlating process parameters, shot profiles, uniaxial tensile properties, and fractography. Improvements on casting conditions and parameters were suggested. Solution heat treatments were carried out between 0.25 and 24 hours and quenched with forced air. Bulk hardness measurements were obtained following solution heat treatment to determine the arrest times for the precipitation reactions during natural aging. The uniaxial tensile properties of the alloy in the F- and T4-tempers were presented. Microstructural analyses of the alloy were carried out by optical and electron microscopy (SEM), including phase identification, phase fraction, average grain size, and distribution. A predictive model for the homogenization of the solutes in the Al matrix was developed using a one-dimensional diffusion model with spherical geometry, and a MATLAB code was developed to time for complete homogenization. Electron-dispersive X-ray spectroscopy (EDX) line scans were carried out on the F and T4 samples (0.25-2h) and the concentration profiles of Zn and Mg (the diffusing solutes) were extracted and analyzed. The models were verified and validated with experiment data. / Thesis / Master of Applied Science (MASc)