<p>There are significant problems during construction to establish an adequate foundation for fills and/or subgrade for pavements when the natural ground has low-bearing soils. Geosynthetics such as geogrids, geotextiles and/or geocells could provide an alternative, less costly in time and money, to establish an adequate foundation for the fill and/or subgrade. There is extensive evidence in the literature and on DOTs practices about the suitability of using geotextiles in pavements as separators. Previous studies have also shown that the use of geogrids in flexible pavements as a reinforcing mechanism could decrease the thickness of the base layer and/or increase the life of the pavement. In this study, analyses of selected pavement designs using Pavement ME, while considering geogrid-enhanced base or subgrade resilient modulus values, showed that geogrid-reinforcement, when placed at the interface between subgrade and base, did not produce significant benefits, as only a modest increase in pavement life was predicted. In addition, parametric finite element analyses were carried out to investigate the potential benefits of placing a geogrid at the base of a fill over a localized weak foundation zone. The analyses showed that the use of geogrids is beneficial only when: (a) the stiffness of the weak foundation soil is about an order of magnitude smaller than the rest of the foundation soil; and (b) the horizontal extent of the weak foundation soil is at least 30% of the base of the embankment foundation. The largest decrease in differential settlements at the surface of the fill, resulting from geogrid-reinforcement, was less than 20% and, therefore, it is unlikely that the sole use of geogrids would be sufficient to mitigate differential settlements. Based on previous studies, a geocell mattress, which is a three-dimensional geosynthetic filled with different types of materials, could act as a stiff platform at the base of an embankment and bridge over weak zones in the foundation. However, given the limited experience on the use of geocells, further research is required to demonstrate that geocells can be effectively used instead of other reinforcement methods.</p>

Railways are one of the largest transportation networks in the world that play an important role in the mass transportation of both the passengers and freight. The speed of trains and as well as the axial load carrying capacity have been increasing significantly during the past few decades to keep in pace with the population and economy growth and to compete with other modes of transportation such as the road, air and water transportation system. Billions of dollars are spent annually for maintenance of rail tracks in the world. The efficient and optimum use of these funds is a challenging task that demands innovative and cutting edge technologies in railway engineering. The railway subgrade is an important part of railway foundation and should be capable of providing a suitable base supporting the ballast and subballast to accommodate the stresses due to traffic loads without failure or excessive deformation. The progressive shear failure is a well-known and age old challenging problem for railways over the world for centuries. The subgrade of railway track which typically constitutes of fine-grained material tends to fail through the accumulation of soil movements up- and sideward developing a path for the least resistance along which progressive shear failure occurs under repeated train-induced loads and due to the effects of climate factors. To-date, limited number of studies have addressed failure mechanism associated with the progressive shear failure, especially using the mechanics of unsaturated soils. In this thesis, a novel and first of its kind, Visual Basic program developed in AutoCAD environment based on Mohr-Coulomb failure criteria and unsaturated soil mechanics theory. This program is capable of taking account of the influence of matric suction and simulate progressive shear failure in the subgrade under moving train. Simulation results suggest several parameters that include stress distribution, matric suction, cohesion, coefficient of lateral earth pressure at rest, and coefficient of residual friction as well as the angle of internal friction have a significant effect on the progressive shear failure and the shape of failure planes in the subgrade. The progressive shear failure in subgrade can be reduced by increasing matric suction, cohesion, coefficient of lateral earth pressure at rest, and coefficient of residual friction as well as the angle of internal friction, and optimizing combination of these parameters. The simulation results suggest the progressive shear failure can be well simulated with the Mohr-Coulomb failure criteria. Several suggestions are made for railway subgrade construction and maintenance based on the results of this study.

<p> The central theme of the study is to identify strength-stiffness correlations for chemically treated subgrade soils in Indiana. This was done by conducting Unconfined Compression (UC) tests and resilient modulus tests for soils collected at three different sites, namely : US 31, SR 37 and I-65. At each site, soil samples were obtained from 11 locations at 30 ft spacing. The soils were treated in the laboratory with cement, using the same proportions used for construction, and cured for 7 and 28 days before testing. Results from the UC tests were compared with the resilient modulus results that were available. No direct correlation was found between resilient modulus and UCS parameters for the soils investigated in this study. A brief statistical analysis of the results was conducted, and a simple linear regression model involving the soil characteristics (plasticity index, optimum moisture content and maximum dry density) along with UCS and resilient modulus parameters was proposed.  </p>

No description available.

No description available.

No description available.

No description available.

The Portland Cement Association commissioned a research project at Brigham Young University to compare selected laboratory durability tests available for assessing stabilized subgrade materials. Improved understanding of these tests is needed to enable more objective selection of durability tests by design engineers and to facilitate more meaningful comparisons of data obtained for different stabilizer treatments using different evaluation procedures. The laboratory research associated with this project involved two subgrade materials, four stabilizers at three concentrations each, and three durability tests in a full-factorial experimental design. The two subgrade soils used were a silty sand and a lean clay, while the four stabilizer types included Class C fly ash, lime-fly ash, lime, and Type I/II portland cement. The three tests used in this comparative study were the freeze-thaw test, the vacuum saturation test, and the tube suction test. On average, to achieve the same 7-day unconfined compressive strength (UCS) values, the sand required 4.4 times more Class C fly ash than cement, 3.6 times more lime-fly ash than cement, and 6.0 times more lime than cement. Likewise, the clay required 10 times more Class C fly ash than cement, 7.5 times more lime-fly ash than cement, and 1.8 times more lime than cement. Analyses of the test results indicated that the UCS and retained UCS were higher for specimens tested by vacuum saturation than the corresponding values associated with freeze-thaw cycling. This observation suggests that the freeze-thaw test is more severe than the vacuum saturation test for these particular fine-grained materials. Testing also suggested that specimens with 7-day UCS values below 200 psi will generally not survive freeze-thaw cycling. After both freeze-thaw and vacuum saturation testing, the sand specimens treated with lime-fly ash had significantly higher UCS and retained UCS than specimens treated with Class C fly ash, lime, or cement. Similarly, the clay specimens treated with Class C fly ash or lime-fly ash had significantly higher UCS values than specimens treated with cement or lime; however, clay specimens treated with Class C fly ash and lime-fly ash were not significantly different. None of the four stabilizer types were significantly different from each other with respect to retained UCS after vacuum saturation testing. Dielectric values measured in tube suction testing were lowest for specimens treated with lime-fly ash and cement with respect to the sand and for specimens treated with Class C fly ash and cement with respect to the clay. The lime-fly ash and cement successfully reduced the dielectric value of sand specimens to a "marginal" rating, while no stabilizer reduced the moisture susceptibility of the clay to a satisfactory level. A strong correlation was identified between UCS after the freeze-thaw test and UCS after the vacuum saturation test, while very weak correlations were observed between the final dielectric value after tube suction testing and all other response variables. Differences in variability between test results were determined to be statistically insignificant in an analysis of the CVs associated with data collected in this research. Although the freeze-thaw test utilized in this research was determined to be more severe than the vacuum saturation test for materials similar to those tested in this study, the vacuum saturation test is recommended over both the freeze-thaw and tube suction tests because of the shorter test duration, usability for specimens with 7-day UCS values even below 200 psi, and lack of a need for daily specimen monitoring.

No description available.

O comportamento mecânico do subleito tem influência determinante no desempenho das estruturas de pavimento. Porém, muitas vezes, os estudos realizados para elaboração de projetos são simplistas e não levam em conta as variações de comportamento mecânico que podem ocorrer, seja por fatores construtivos, seja ambientais, como umidade, durante o período de operação. Neste sentido, métodos de dimensionamento mecanicistas-empíricos de estruturas de pavimentos empregam modelos de comportamento das diversas camadas da estrutura e do subleito, sendo alvos de constantes revisões para recalibração destes modelos, de modo que se aproximem mais da realidade do comportamento em serviço. As calibrações dos modelos são necessárias para aumentar a confiabilidade do dimensionamento de modo a garantir pavimentos mais duráveis, e para otimizar custos de execução e de manutenção ao longo da vida útil das estruturas. Neste contexto o presente trabalho propõe uma metodologia para compreender as propriedades dos solos do subleito e de suas variações, estabelecendo um programa de ensaios de campo e de laboratório, cadastramento, processamento e combinação de resultados de propriedades físicas e mecânicas de solos de subleitos de pavimentos de rodovias existentes. O objetivo final é estabelecer parâmetros de deformabilidade elástica de solos do subleito e sua variabilidade para auxiliar no dimensionamento de novas estruturas de pavimentos e reabilitação das antigas. O trabalho utiliza estudos de casos de pavimentos rodoviários em operação. O primeiro caso foi base para o estabelecimento metodológico de estudo desejável do subleito de um pavimento existente, concebendo modelos de previsão de comportamento resiliente do subleito para uso em futuros projetos de restauração deste pavimento ou para novos projetos em locais com similaridade de ocorrência de solos. Empregando a metodologia estabelecida no primeiro caso, fez-se uma busca minuciosa de dados em vários documentos existentes sobre pavimentos rodoviários de concessionárias do Estado de São Paulo, concebendo-se um banco de dados para análise do subleito destes pavimentos, de modo a ampliar a gama de solos pesquisados. Com resultados de caracterização de solos em laboratório e de deflectometria em campo, além de dados de localização dos pontos estudados em mapas geológicos e pedológicos, dados de precipitação, de terraplenagem, entre outros, pôde-se analisar os dados e identificar a influência de cada elemento na variação do módulo de resiliência dos solos de fundação de pavimentos em serviço. O banco de dados de ensaios laboratoriais de solos de subleito contou com um total de 3.894 registros e de ensaios não destrutivos deflectométricos de campo com um total de 169.525 registros (dados históricos de nove rodovias estaduais diferentes). Dentre as principais conclusões, verificou-se que grande parte dos modelos de correlações existentes na literatura entre parâmetros de propriedades físicas e de resistência (como CBR) de solos com o módulo de resiliência possui aplicação muito restrita, inviabilizando sua aplicação de forma indiscriminada em locais distintos daqueles onde foram obtidas as correlações. Além disso, verificou-se que o módulo de resiliência do subleito em campo apresenta variações de grande magnitude e, portanto, é de difícil previsão, requerendo acumulação de dados históricos, bem como de um cadastro adicional de maior gama de informações. Recomenda-se que maiores quantidades de ensaios sejam realizadas e que permitam verificação, ou dupla checagem, para validação, bem como para futuramente ser possível o estabelecimento de modelos matemáticos mais confiáveis. Nos estudos, foi possível estabelecer parâmetros estatísticos que podem ser utilizados tanto em métodos de dimensionamento vigentes ou novos, como naquelas que consideram as variações do módulo de resiliência do subleito para determinação do risco de falha, ou da confiabilidade das estruturas. / Subgrade mechanical behavior has a determining influence on the performance of pavement structures. However, often, the studies carried out for project designs are simplistic and do not take into account the variations that can occur in the mechanical behavior, whether by constructive factors or environmental ones, such as the moisture content during the operation period. Thus, mechanical-empirical design methods of pavement structures employ performance models of the many layers of the structure and of the subgrade, being targets of constant revisions for adjustment of these models so that they come closer to reality in operation behavior. Model adjustments are necessary to increase design reliability to ensure more durable pavements and to optimize execution and maintenance costs during the structure life. In this context, the present work proposes a methodology to understand the subgrade soil properties and their variations, establishing a program of field and laboratory tests, registration, processing and combination of results of physical and mechanical properties of subgrade soils of existing highway pavements. The final objective is to establish parameters of the subgrade soil elastic deformability and their variability to assist in the design of new pavement structures and in the rehabilitation of old ones. This work uses case studies of road pavements in operation. The first case was the basis for the methodological establishment of a desirable study of the subgrade of an existing pavement, designing predictive models of the subgrade resilient behavior for use in future rehabilitation projects of this pavement or for new projects in places with a similar occurrence of soils. By using the methodology established in the first case, a thorough data search was carried out in several existing documents on road pavements of concessionaires in the State of São Paulo, and a database was prepared to analyze the subgrade of such pavements in order to expand the range of soils studied. With the results of soil characterization in the laboratory and by field deflections, in addition to location data of the points studied in geological and pedological maps, precipitation and earthwork data, among others, it was possible to analyze the data and identify the influences of each element on the variation of the subgrade resilient modulus of the pavements in operation. The database from laboratory tests of subgrade soils covered a total of 3,894 registers and of non-destructive deflectometric field tests - a total of 169,525 registers (historical data on nine different state highways). Among the main conclusions, it was verified that most of the correlation models existing in the literature between parameters of physical and mechanical strength properties (like the CBR) of soils with the resilient moduli have very restricted application, making it impossible to apply them indiscriminately in places other than those where the correlations were obtained. In addition, it was verified that the resilient modulus of the subbase in situ presents variations of great magnitude and, therefore, it is difficult to make predictions. Lots of historical data are required, as well as additional registers of a greater range of information. Therefore, it is recommended that a larger number of tests be performed in order to allow for checking and double-checking for validation as well as the possibility of a future establishment of more reliable mathematical models. In the studies, it was possible to establish statistical parameters that can be used both in current and in new design methods, like in those that consider variations of the subgrade resilient moduli to determine the risk of failure or of the reliability of structures.