Biogas production from organic materials can be used as a renewable vehicle fuel, provide heat and generate electricity and can thereby reduce the greenhouse gas emissions. This thesis focuses on the biogas production based on lignocelluloses. There is an abundant availability of lignocelluloses, constituting 50% of the total biomass worldwide. However, the biomass recalcitrance limits the microbial degradation as well as the biogas production from these types of materials. In the present work different pretreatment methods have been performed in order to decrease the biomass recalcitrance and improve the biogas production. Steam explosion pretreatment, together with the addition of sodium hydroxide and hydrogen peroxide, has been performed on lignocellulosic-rich paper tube residuals. The pretreatment has resulted in methane yields of up to 493 NmL/gVS, which is an increase by 107% compared with untreated material. Furthermore, the use of an organic solvent, N-methylmorpholine-N-oxide (NMMO), was evaluated as a pretreatment method for spruce (both chips and milled), rice straw, and triticale straw. The NMMO pretreatment resulted in 202, 395, 328, and 362 NmL CH4/g carbohydrates produced of these substrates, respectively, corresponding to an increase of between 400-1,200% compared with the untreated version of the same material. Moreover, the paper tube residuals have been co-digested with an unstable nitrogen-rich substrate mixture, mainly based on municipal solid waste. The addition of the lignocellulosic-rich paper tubes in a co-digestion process showed stabilizing effects and prevented the accumulation of volatile fatty acids with a subsequent reactor failure. Additionally, synergistic effects have been found leading to between 15-33% higher methane yields when paper tubes were added to the co-digestion process compared with the yields calculated from the methane potentials of the two substrates. Substrate characterization analysis can be used to study the changes on the lignocellulosic components after the pretreatment, relating the changes to the performance in the anaerobic digestion. Increased accessible surface area, measured by the Simons’ stain and the enzymatic adsorption methods, as well as decreased crystallinity, determined by using the Fourier Transform Infrared Spectroscopy, can all be linked to improved biogas production after pretreatment. Finally, the NMMO pretreatment on forest residues has been financially evaluated for an industrial scale process design. The base case that was evaluated simulated a case where pretreated forest residues were co-digested with the organic fraction of municipal solid waste to obtain optimal nutritional balance for the anaerobic digestion. This process has been found to be economically feasible with an internal rate of return of 20.7%. / <p>Akademisk avhandling som för avläggande av teknologie doktorsexamen vid Chalmers tekniska högskola försvaras vid offentlig disputation den 24 maj 2013, klockan 10.00 i KA,Kemigården 4, Göteborg</p>

La technologie MID (Molded Interconnect Device), fait de leur performance électrique, la flexibilitédans les circuits RF, le potentiel de réduire le nombre de composants, les étapes du processus et laminiaturisation du produit final, a conduit à de nouvelles contraintes à la RF (Radio Frequency) et ledomaine des micro-ondes. Composants moulés sont interconnectées avec des substratsthermoplastiques et les pistes conductrices sont injectés sur la surface. L'objectif de cette thèse estd'étudier la compatibilité de MID pour les applications RF. Les avantages de la technologie MID dansle domaine RF est exploitée pour les lignes de transmission, filtres passifs, coupleurs directionnels etantennes réalisation. La caractérisation RF de différents matériaux de substrat MID et l'étude de laperformance des composants RF ci-dessus sur la base de différentes technologies de fabrication MIDsont inclus dans la thèse. Enfin, le concept d'une étude d'amélioration de la permittivité de certainsthermoplastiques sont également étudiés. / MID (Molded Interconnect Devices) technology, owing to their electrical performance,flexibility in RF circuits, its potential to reduce the number of components, process steps andminiaturization of the final product, has led to some new constraints to the RF (RadioFrequency) and microwave domain. Molded components are interconnected withthermoplastic substrates and conductive traces are injected on the surface. The objective ofthis thesis is to study the compatibility of MIDs for RF applications. The advantages of MIDtechnology in the RF domain is exploited for transmission lines, passive filters, directionalcouplers and planar and 3D antennas realization. The RF characterization of various MIDsubstrate materials and the study of the performance of the above RF components based onvarious MID fabrication technologies are included in the thesis. Finally, an permittivityimprovement study of some thermoplastics are also studied.

La technologie MID (Molded Interconnect Device), fait de leur performance électrique, la flexibilitédans les circuits RF, le potentiel de réduire le nombre de composants, les étapes du processus et laminiaturisation du produit final, a conduit à de nouvelles contraintes à la RF (Radio Frequency) et ledomaine des micro-ondes. Composants moulés sont interconnectées avec des substratsthermoplastiques et les pistes conductrices sont injectés sur la surface. L'objectif de cette thèse estd'étudier la compatibilité de MID pour les applications RF. Les avantages de la technologie MID dansle domaine RF est exploitée pour les lignes de transmission, filtres passifs, coupleurs directionnels etantennes réalisation. La caractérisation RF de différents matériaux de substrat MID et l'étude de laperformance des composants RF ci-dessus sur la base de différentes technologies de fabrication MIDsont inclus dans la thèse. Enfin, le concept d'une étude d'amélioration de la permittivité de certainsthermoplastiques sont également étudiés. / MID (Molded Interconnect Devices) technology, owing to their electrical performance,flexibility in RF circuits, its potential to reduce the number of components, process steps andminiaturization of the final product, has led to some new constraints to the RF (RadioFrequency) and microwave domain. Molded components are interconnected withthermoplastic substrates and conductive traces are injected on the surface. The objective ofthis thesis is to study the compatibility of MIDs for RF applications. The advantages of MIDtechnology in the RF domain is exploited for transmission lines, passive filters, directionalcouplers and planar and 3D antennas realization. The RF characterization of various MIDsubstrate materials and the study of the performance of the above RF components based onvarious MID fabrication technologies are included in the thesis. Finally, an permittivityimprovement study of some thermoplastics are also studied.