À l’horizon 2024, l’expérience ATLAS prévoit de fonctionner à des luminosités 10 fois supérieures à la configuration actuelle. Par conséquent, l’électronique actuelle de lecture ne correspondra pas aux conditions de ces luminosités. Dans ces conditions, une nouvelle électronique devra être conçue. Cette mise à niveau est rendue nécessaire aussi par les dommages causés par les radiations et le vieillissement. Une nouvelle carte frontale va être intégrée dans l’électronique de lecture du calorimètre LAr. Un élément essentiel de cette carte est le Convertisseur Analogique-Numérique (CAN) présentant une résolution de 12bits pour une fréquence d’échantillonnage de 40MS/s, ainsi qu’une résistance aux irradiations. Compte tenu du grand nombre des voies, ce CAN doit remplir des critères sévères sur la consommation et la surface. Le but de cette thèse est de concevoir un CAN innovant qui peut répondre à ces spécifications. Une architecture à approximations successives (SAR) a été choisie pour concevoir notre CAN. Cette architecture bénéficie d’une basse consommation de puissance et d’une grande compatibilité avec les nouvelles technologies CMOS. Cependant, le SAR souffre de certaines limitations liées principalement aux erreurs de décisions et aux erreurs d’appariement des capacités du CNA. Deux prototypes de CAN-SAR 12bits ont été modélisés en Matlab afin d’évaluer leur robustesse. Ensuite les conceptions ont été réalisées dans une technologie CMOS 130nm d’IBM validée par la collaboration ATLAS pour sa tenue aux irradiations. Les deux prototypes intègrent un algorithme d’approximations avec redondance en 14 étapes de conversion, qui permet de tolérer des marges d’erreurs de décisions et d’ajouter une calibration numérique des effets des erreurs d’appariement des capacités. La partie logique de nos CAN est très simplifiée pour minimiser les retards de génération des commandes et la consommation d’énergie. Cette logique exécute un algorithme monotone de commutation des capacités du CNA permettant une économie de 70% de la consommation dynamique par rapport à un algorithme de commutation classique. Grâce à cet algorithme, une réduction de capacité totale est aussi obtenue : 50% en comparant notre premier prototype à un seul segment avec une architecture classique. Pour accentuer encore plus le gain en termes de surface et de consommation, un second prototype a été réalisé en introduisant un CNA à deux segments. Cela a abouti à un gain supplémentaire d’un facteur 7,64 sur la surface occupée, un facteur de 12 en termes de capacité totale, et un facteur de 1,58 en termes de consommation. Les deux CAN consomment respectivement une puissance de ~10,3mW et ~6,5mW, et ils occupent respectivement une surface de ~2,63mm2 et ~0,344mm2.Afin d’améliorer leurs performances, un algorithme de correction numérique des erreurs d’appariement des capacités a été utilisé. Des buffers de tensions de référence ont étés conçus spécialement pour permettre la charge/décharge des capacités du convertisseur en hautes fréquences et avec une grande précision. En simulations électriques, les deux prototypes atteignent un ENOB supérieur à 11bits tout en fonctionnant à la vitesse de 40MS/s. Leurs erreurs d’INL simulés sont respectivement +1,14/-1,1LSB et +1,66/-1,72LSB.Les résultats de tests préliminaires du premier prototype présentent des performances similaires à celles d’un CAN commercial de référence sur notre carte de tests. Après la correction, ce prototype atteint un ENOB de 10,5bits et un INL de +1/-2,18LSB. Cependant suite à une panne de carte de tests, les résultats de mesures du deuxième prototype sont moins précis. Dans ces circonstances, ce dernier atteint un ENOB de 9,77bits et un INL de +7,61/-1,26LSB. En outre la carte de tests actuelle limite la vitesse de fonctionnement à ~9MS/s. Pour cela une autre carte améliorée a été conçue afin d’atteindre un meilleur ENOB, et la vitesse souhaitée. Les nouvelles mesures vont être publiées dans le futur. / By 2024, the ATLAS experiment plan to operate at luminosities 10 times the current configuration. Therefore, many readout electronics must be upgraded. This upgrade is rendered necessary also by the damage caused by years of total radiations’ effect and devices aging. A new Front-End Board (FEB) will be designed for the LAr calorimeter readout electronics. A key device of this board is a radiation hard Analog-to-Digital Converter (ADC) featuring a resolution of 12bits at 40MS/s sampling rate. Following the large number of readout channels, this ADC device must display low power consumption and also a low area to easy a multichannel design.The goal of this thesis is to design an innovative ADC that can deal with these specifications. A Successive Approximation architecture (SAR) has been selected to design our ADC. This architecture has a low power consumption and many recent works has shown his high compatibility with modern CMOS scaling technologies. However, the SAR has some limitations related to decision errors and mismatches in capacitors array.Using Matlab software, we have created the models for two prototypes of 12bits SAR-ADC which are then used to study carefully their limitations, to evaluate their robustness and how it could be improved in digital domain.Then the designs were made in an IBM 130nm CMOS technology that was validated by the ATLAS collaboration for its radiation hardness. The prototypes use a redundant search algorithm with 14 conversion steps allowing some margins with comparator’s decision errors and opening the way to a digital calibration to compensate the capacitors mismatching effects. The digital part of our ADCs is very simplified to reduce the commands generation delays and saving some dynamic power consumption. This logic follows a monotonic switching algorithm which saves about70% of dynamic power consumption compared to the conventional switching algorithm. Using this algorithm, 50% of the total capacitance reduction is achieved when one compare our first prototype using a one segment capacitive DAC with a classic SAR architecture. To boost even more our results in terms of area and consumption, a second prototype was made by introducing a two segments DAC array. This resulted in many additional benefits: Compared to the first prototype, the area used is reduced in a ratio of 7,6, the total equivalent capacitance is divided by a factor 12, and finally the power consumption in improved by a factor 1,58. The ADCs respectively consume a power of ~10,3mW and ~6,5mW, and they respectively occupy an area of ~2,63mm2 and ~0,344mm2.A foreground digital calibration algorithm has been used to compensate the capacitors mismatching effects. A high frequency open loop reference voltages buffers have been designed to allow the high speed and high accuracy charge/discharge of the DAC capacitors array.Following electrical simulations, both prototypes reach an ENOB better than 11bits while operating at the speed of 40MS/s. The INL from the simulations were respectively +1.14/-1.1LSB and +1.66/-1.72LSB.The preliminary testing results of the first prototype are very close to that of a commercial 12bits ADC on our testing board. After calibration, we measured an ENOB of 10,5bits and an INL of +1/-2,18LSB. However, due to a testing board failure, the testing results of the second prototype are less accurate. In these circumstances, the latter reached an ENOB of 9,77bits and an INL of +7,61/-1,26LSB. Furthermore the current testing board limits the operating speed to ~9MS/s. Another improved board was designed to achieve a better ENOB at the targeted 40MS/s speed. The new testing results will be published in the future.

Conselho Nacional de Desenvolvimento Científico e Tecnológico / New trends and emerging technologies motivate the design of analog-to-digital converters (ADCs) which must fit in increasingly constrained environments. Within this context, one design metric which is constantly forced towards reduction is the power consumption, leading the designers to come up with improvements in both the architecture and circuit levels. This work aims to push forward the energy efficiency of the successive approximation charge sharing ADC, which is a relatively new and unexplored architecture. Therefore, three complete ADCs are designed throughout this work, each one bringing novelties that help decreasing the power consumption. The techniques devised here include novel manners of dealing with the tracking of the input signal and a circuit to reduce power drained in the pre-charge cycle. Also, three different architectures of digital controller for this ADC topology are designed. Moreover, a novel bootstrapping switch circuit is presented, which provides lower devices-count and a extremely high energy efficiency. / As novas tendências e tecnologias emergentes motivam o projeto de conversores analógico-digitais (ADCs) que precisam suprir especificações cada vez mais restritivas. Nesse contexto, uma métrica de projeto que é constantemente forçada em direção à redução é o consumo de potência, fato esse que leva à concepção de melhorias tanto em nível arquitetural como em nível de circuito elétrico. Este trabalho tem como objetivo elevar a eficiência energética dos ADCs por aproximações sucessivas e compartilhamento de carga, visto que essa é uma arquitetura relativamente nova e inexplorada. Portanto, três ADCs completos são projetados ao longo deste trabalho, e cada um traz inovações que ajudam a reduzir o consumo de potência. As técnicas concebidas aqui incluem maneiras novas de efetuar a captura do sinal de entrada e um circuito para reduzir a potência drenada no ciclo de pré-carga. Além disso, três arquiteturas diferentes de controlador digital para essa topologia de ADC são expostas. Mais, um novo circuito de chave com bootstrapping é apresentado, o qual apresenta um número de dispositivos menor e uma eficiência energética extremamente alta.

Silicon carbide (SiC) integrated circuits (ICs) can enable the emergence of robust and reliable systems, including data acquisition and on-site control for extreme environments with high temperature and high radiation such as deep earth drilling, space and aviation, electric and hybrid vehicles, and combustion engines. In particular, SiC ICs provide significant benefit by reducing power dissipation and leakage current at temperatures above 300 °C compared to the Si counterpart. In fact, Si-based ICs have a limited maximum operating temperature which is around 300 °C for silicon on insulator (SOI). Owing to its superior material properties such as wide bandgap, three times larger than Silicon, and low intrinsic carrier concentration, SiC is an excellent candidate for high-temperature applications. In this thesis, analog and mixed-signal circuits have been implemented using SiC bipolar technology, including bandgap references, amplifiers, a master-slave comparator, an 8-bit R-2R ladder-based digital-to-analog converter (DAC), a 4-bit flash analog-to-digital converter (ADC), and a 10-bit successive-approximation-register (SAR) ADC. Spice models were developed at binned temperature points from room temperature to 500 °C, to simulate and predict the circuits’ behavior with temperature variation. The high-temperature performance of the fabricated chips has been investigated and verified over a wide temperature range from 25 °C to 500 °C. A stable gain of 39 dB was measured in the temperature range from 25 °C up to 500 °C for the inverting operational amplifier with ideal closed-loop gain of 40 dB. Although the circuit design in an immature SiC bipolar technology is challenging due to the low current gain of the transistors and lack of complete AC models, various circuit techniques have been applied to mitigate these problems. This thesis details the challenges faced and methods employed for device modeling, integrated circuit design, layout implementation and finally performance verification using on-wafer characterization of the fabricated SiC ICs over a wide temperature range. / <p>QC 20170905</p>