Polymer solar cells are promising in that they are inexpensive to produce, and due to their mechanical flexibility have the potential for use in applications not possible for more traditional types of solar cells. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor material in the active layer. Understanding the connection between morphology and performance as well as how to control the morphology, is therefore of great importance. Furthermore, improving the lifetime of polymer solar cells has become at least as important as improving the efficiency.   In this thesis, the relation between morphology and solar cell performance is studied, and the material stability for blend films of the thiophene-quinoxaline copolymer TQ1 and the fullerene derivatives PCBM and PC70BM. Atomic force microscopy (AFM) and scanning transmission X-ray microscopy (STXM) are used to investigate the lateral morphology, secondary ion mass spectrometry (SIMS) to measure the vertical morphology and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to determine the surface composition. Lateral phase-separated domains are observed whose size is correlated to the solar cell performance, while the observed TQ1 surface enrichment does not affect the performance. Changes to the unoccupied molecular orbitals as a result of illumination in ambient air are observed by NEXAFS spectroscopy for PCBM, but not for TQ1. The NEXAFS spectrum of PCBM in a blend with TQ1 changes more than that of pristine PCBM. Solar cells in which the active layer has been illuminated in air prior to the deposition of the top electrode exhibit greatly reduced electrical performance. The valence band and absorption spectrum of TQ1 is affected by illumination in air, but the effects are not large enough to account for losses in solar cell performance, which are mainly attributed to PCBM degradation at the active layer surface. / The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor material in the active layer. Understanding the connection between morphology and performance as well as how to control the morphology, is therefore of great importance. Furthermore, improving the lifetime has become at least as important as improving the efficiency for polymer solar cells to become a viable technology.   In this work, the relation between morphology and solar cell performance is studied as well as the material stability for polymer:fullerene blend films. A combination of microscopic and spectroscopic methods is used to investigate the lateral and vertical morphology as well as the surface composition. Lateral phase-separated domains are observed whose size is correlated to the solar cell performance, while the observed surface enrichment of polymer does not affect the performance. Changes to the unoccupied molecular states as a result of illumination in ambient air are observed for the fullerene, but not for the polymer, and fullerenes in a blend change more than pristine fullerenes. Solar cells in which the active layer has been illuminated exhibit greatly reduced electrical performance, mainly attributed to fullerene degradation at the active layer surface. / <p>Paper 2 ingick som manuskript i avhandlingen. Nu publicerad. </p>

Polymer solar cells form a promising technology for converting sunlight into electricity, and have reached record efficiencies over 10% and lifetimes of several years. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor materials in the active layer. To achieve longer lifetimes, degradation processes in the materials have to be understood. In this thesis, a set of complementary spectroscopy and microscopy techniques, among which soft X-ray techniques have been used to determine the morphology of polymer:fullerene based active layers. We have found that the morphology of TQ1:PC70BM films is strongly influenced by the processing solvent and the use of solvent additives. We have also found, by using soft X-ray techniques, that not only the light-absorbing polymer TQ1, but also the fullerene is susceptible to photo-degradation in air. Moreover, the fullerene degradation is accelerated in the presence of the polymer. Additionally, this thesis addresses the role of the interfacial layers for device performance and stability. The commonly used hole transport material PEDOT:PSS has the advantage of being solution processable at room temperature, but this layer is also known to contribute to the device degradation. We have found that low-temperature processed NiOx is a promising alternative to PEDOT:PSS, leading to improved device performance. Even for encapsulated polymer solar cells, some photo-induced degradation of the electrical performance is observed and is found to depend on the nature of the hole transport material. We found a better initial stability for solar cells with MoO3 hole transport layers than with PEDOT:PSS. In the pursuit of understanding the initial decrease in electrical performance of PEDOT:PSS-based devices, simulations were performed, from which a number of degradation sources could be excluded. / With the increasing global demand for energy, solar cells provide a clean method for converting the abundant sunlight to electricity. Polymer solar cells can be made from a large variety of light-harvesting and electrically conducting molecules and are inexpensive to produce. They have additional advantages, like their mechanical flexibility and low weight, which opens opportunities for novel applications. In order for polymer solar cells to be more competitive, however, both the power conversion efficiencies and lifetimes need to further improve. One way to achieve this is to optimize the morphology of the active layer. The active layer of a polymer solar cell consists of electron donating and electron accepting molecules whose distribution in the bulk of the film is a major factor that determines the solar cell performance. This thesis presents the use of complementary spectroscopy and microscopy methods to probe the local composition in the active layer of polymer solar cells. The stability of the active layer is studied and the interplay between the photo-degradation of the donor and acceptor molecules is investigated. Additionally, this thesis addresses how the interfacial layers between the active layer and the electrodes can influence device performance and stability. / <p>I publikationen felaktigt ISBN 978-91-7063-739-1</p>

Polymer-based photovoltaics have the potential to contribute to boosting photovoltaic energy conversion overall. Besides allowing large-area inexpensive processing, polymeric materials have the added benefit of opening new market applications for photovoltaics due to their low-weight and interesting mechanical properties. The energy conversion efficiency values of polymer photovoltaics have reached new record values over the past years. It is however crucial that stability issues are addressed together with efficiency optimization. Understanding fundamental materials aspects is key in both areas. In the work presented in this thesis, the morphology of polymer:fullerene films and its influence on device performance was studied, as well as the effect of light exposure on the surface of fullerene films. Several polyfluorene copolymers were used for the morphology studies, where the effects of changing spin-coating solvent and of side chain engineering were investigated with dynamic secondary ion mass spectrometry (dSIMS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Polymer-enriched surfaces were found in all blend films, even in the cases with homogeneous distributions in the bulk. Side chain engineering of the polymer led to gradual changes in the compositional variations perpendicular to the surface, and to slight variations in the photocurrent. The electronic structure of the fullerene derivative PCBM was studied in detail and the spectroscopic fingerprint of the materials was analysed by comparison with theoretically simulated spectra. Photo-stability studies done in air showed that the surface of fullerene films underwent severe damages at the molecular level, which is evident from changes in the valence band and X-ray absorption spectra. These changes were explained by transitions from sp2-type to sp3 hybridization of the carbon atoms in the cage that resulted in the destruction of the fullerene cage.