No description available.

No description available.

The aim of this research was to study a novel, broadband, low cost, low profile and a high-medium gain antenna in the UHF band. This has been achieved through numerical modelling, theoretical investigation and physical measurements. In this study two commercially available antenna systems are investigated in order to compare and establish potential deficiencies in the UHF antenna systems. A number of disadvantages are resolved within a novel antenna system design. The parametric study is performed for each element of the novel antenna system in order to optimise its overall performance. The indoor and outdoor measurements have been carried out in house, in order to validate the predicted results. The novel antenna system is compared to the most popular and commercially available UHF antenna systems. The study demonstrates that the novel antenna system has clear advantages such as broadband, balanced, compact and low cost when compared to the commercial antenna designs studied here. The comparison of the manufacturers' data to the measured results shows a good match, validating the outdoor measurements technique used in this research.

Polarization dependences of optical devices in highly-integrated optical systems become a major problem. To overcome this issue, one can implement polarization diversity scheme to achieve a single polarization on-chip network. One of the essential components in a polarization diversity scheme is the polarization beam splitter (PBS). In this thesis, we will a PBS based on a silicon-on-insulator (SOI) platform with reduced device size and broad operation bandwidth. We use the three-dimensional Finite-Difference Time-Domain (3D-FDTD) method to perform the simulation. First, we use two asymmetric waveguides to design an asymmetric directional coupler with only TE-like mode phase matching condition. We then tape the lower waveguide to keep the TE-polarized light, and split the TE- and TM- polarized light. By utilizing an asymmetrical directional coupler with a tapered waveguide, we have achieved a 7.3

Metal building frames are typically designed using welded prismatic and web-tapered members with doubly-symmetric and/or singly-symmetric cross sections. Until recently, the base U.S. provisions for design of frames with web-tapered members were provided in the AISC ASD (1989) and LRFD (1999) Specifications. Unfortunately, these previous AISC provisions address only a small range of practical designs. As a result, metal building manufacturers have tended to develop their own methods for design of the wide range of nonprismatic member geometries and configurations encountered in practice. This research develops new design procedures for design of frames using general prismatic members and web-tapered members. An equivalent prismatic member concept utilized in prior research and the prior AISC provisions is generalized to accommodate the broad range of member types and configurations commonly used in metal building industry. Furthermore, the new design procedures incorporate many of the improvements achieved in the AISC (2005&2010) Specifications to metal building frame design. These improvements include a new stability design method, the direct analysis method, more complete considerations of different column buckling limit states (flexural, torsional and flexural-torsional buckling), and improved axial load and flexural resistance provisions. This research develops practical design-based procedures for simplified calculation of the elastic buckling resistances of prismatic and web-tapered members to facilitate the application of the proposed design methods. In addition, this research performs a relatively comprehensive assessment of beam lateral torsional buckling (LTB) behavior and strength of prismatic and web-tapered members using refined virtual test simulation. It is demonstrated that web-tapered members behave in a comparable fashion to prismatic members. Based on the virtual simulation study, recommendations for potential improvement of the AISC LTB resistance equations are provided. Lastly, the strength behavior of several representative metal building frames is studied in detail using the same virtual test simulation capabilities developed and applied for the assessment of the beam LTB resistances.

iv ABSTRACT DESIGN AND CONSTRUCTION OF REDUCED SIZE PLANAR SPIRAL ANTENNA IN THE 0.5-18 GHz FREQUENCY RANGE YILDIZ, 5nan&ccedil / M.S., Department of Electrical and Electronics Engineering Supervisor: Prof. Dr. Altunkan HIZAL October 2004, 106 pages In this thesis, theoretical and practical evaluation of usual spiral antenna is revised. Working principles of both types of planar spiral antennas as Equiangular and Archimedean are introduced. A predesigned microstrip tapered balun used for feeding section of a spiral antenna is simulated on Ansoft HFSS software. Successful simulation results are obtained and measurements of implemented balun structure are made by using an HP 8722 D vector network analyzer. Antenna measurement techniques used in this study are introduced. Measurement set-ups are defined and some preliminary knowledge is given on these. As the main matter of thesis, reduced size planar spiral antennas are designed and implemented. Return loss, gain / radiation and polarization patterns of antennas are measured. Datasets of measurements are compared with each other and with reference spiral antenna. Quite promising results are obtained and size reduction of spiral antenna is achieved in many aspects.

Spanwise nonuniformity effects are modeled in the cross-sectional analysis of beam theory. This modeling adheres to an established numerical framework on cross-sectional analysis of uniform beams with arbitrary cross-sections. This framework is based on two concepts: decomposition of the rotation tensor and the variational-asymptotic method. Allowance of arbitrary materials and geometries in the cross-section is from discretization of the warping field by finite elements. By this approach, dimensional reduction from three-dimensional elasticity is performed rigorously and the sectional strain energy is derived to be asymptotically-correct. Elastic stiffness matrices are derived for inputs into the global beam analysis. Recovery relations for the displacement, stress, and strain fields are also derived with care to be consistent with the energy. Spanwise nonuniformity effects appear in the form of pointwise and sectionwise derivatives, which are approximated by finite differences. The formulation also accounts for the effects of spanwise variations in initial twist and/or curvature. A linearly tapered isotropic strip is analyzed to demonstrate spanwise nonuniformity effects on the cross-sectional analysis. The analysis is performed analytically by the variational-asymptotic method. Results from beam theory are validated against solutions from plane stress elasticity. These results demonstrate that spanwise nonuniformity effects become significant as the rate at which the cross-sections vary increases. The modeling of transverse shear modes of deformation is accomplished by transforming the strain energy into generalized Timoshenko form. Approximations in this transformation procedure from previous works, when applied to uniform beams, are identified. The approximations are not used in the present work so as to retain more accuracy. Comparison of present results with those previously published shows that these approximations sometimes change the results measurably and thus are inappropriate. Static and dynamic results, from the global beam analysis, are calculated to show the differences between using stiffness constants from previous works and the present work. As a form of validation of the transformation procedure, calculations from the global beam analysis of initially twisted isotropic beams from using curvilinear coordinate axes featuring twist are shown to be equivalent to calculations using Cartesian coordinates.

Thanks to their capability of transmitting light with low loss, optical fibers have found a wide range of applications in illumination, imaging, and telecommunication. However, since the light guided in a regular optical fiber is well confined in the core and effectively isolated from the environment, the fiber does not allow the interactions between the light and matters around it, which are critical for many sensing and actuation applications. Specially shaped optical fibers endow the guided light in optical fibers with the capability of interacting with the environment by modifying part of the fiber into a special shape, while still preserving the regular fiber’s benefit of low-loss light delivering. However, the existing specially shaped fibers have the following limitations: 1) limited light coupling efficiency between the regular optical fiber and the specially shaped optical fiber, 2) lack special shape designs that can facilitate the light-matter interactions, 3) inadequate material selections for different applications, 4) the existing fabrication setups for the specially shaped fibers have poor accessibility, repeatability, and controllability. The overall goal of this dissertation is to further the fundamental understanding of specially shaped fibers and to develop novel specially shaped fibers for different applications. In addition, the final part of this dissertation work proposed a microfluidic platform that can potentially improve the light-matter interactions of the specially shaped fibers in fluidic environments. The contributions of this dissertation work are summarized as follows: 1) An enhanced fiber tapering system for highly repeatable adiabatic tapered fiber fabrications. An enhanced fiber tapering system based on a novel heat source and an innovative monitoring method have been developed. The novel heat source is a low-cost ceramic housed electric furnace (CHEF). The innovative monitoring method is based on the frequency-domain optical transmission signal from the fiber that is being tapered. The enhanced fiber tapering system can allow highly repeatable fabrication of adiabatically tapered fibers. 2) A lossy mode resonance (LMR) sensor enabled by SnO2 coating on a novel specially shaped fiber design has been developed. The developed LMR sensor has a D-shape fiber tip with SnO2 coating. It has the capability of relative humidity and moisture sensing. The fiber-tip form factor can allow the sensor to be used like a probe and be inserted into/removed from a tight space. 3) Specially shaped tapered fibers with novel designs have been developed for integrated photonic and microfluidic applications. Two novel specially tapered fibers, the tapered fiber loop and the tapered fiber helix have been developed. The tapered fiber loop developed in this work has two superiority that differentiated itself from previous works: a) the mechanical stability of the tapered fiber loop in this work is significantly better. b) the tapered fiber loops in this work can achieve a diameter as small as 15 ?m while still have a high intrinsic optical quality factor of 32,500. The tapered fiber helix developed in this work has a 3D structure that allows it to efficiently deliver light to locations out of the plane defined by its two regular fiber arms. Applications of the tapered fiber helices in both integrated photonic device characterizations and microparticle manipulations have been demonstrated. 4) Developed an acrylic-tape hybrid microfluidic platform that can allow function reconfiguration and optical fiber integration. A low-cost, versatile microfluidic platform based on reconfigurable acrylic-tape hybrid microfluidic devices has been developed. To the best of the author’s knowledge, this is the first time that the fabrication method of sealing the acrylic channel with a reconfigurable functional tape has been demonstrated. The tape-sealing method is compatible with specially shaped fiber integrations.

This paper deals with sinuous broadband antenna, witch operating frequency 1 to 6 GHz. The antenna parameters, which change their physical dimension were shown in this paper. Antenna structure is planar and feeding network line have to be planar too. There are different ways to describe and construct from unbalanced to balanced line by baluns. There are also design impedance transform to match antenna in this paper. The simulation and measured results are showen the antenna has wideband character.

Thanks to their capability of transmitting light with low loss, optical fibers have found a wide range of applications in illumination, imaging, and telecommunication. However, since the light guided in a regular optical fiber is well confined in the core and effectively isolated from the environment, the fiber does not allow the interactions between the light and matters around it, which are critical for many sensing and actuation applications. Specially shaped optical fibers endow the guided light in optical fibers with the capability of interacting with the environment by modifying part of the fiber into a special shape, while still preserving the regular fiber’s benefit of low-loss light delivering. However, the existing specially shaped fibers have the following limitations: 1) limited light coupling efficiency between the regular optical fiber and the specially shaped optical fiber, 2) lack special shape designs that can facilitate the light-matter interactions, 3) inadequate material selections for different applications, 4) the existing fabrication setups for the specially shaped fibers have poor accessibility, repeatability, and controllability. The overall goal of this dissertation is to further the fundamental understanding of specially shaped fibers and to develop novel specially shaped fibers for different applications. In addition, the final part of this dissertation work proposed a microfluidic platform that can potentially improve the light-matter interactions of the specially shaped fibers in fluidic environments. The contributions of this dissertation work are summarized as follows: 1) An enhanced fiber tapering system for highly repeatable adiabatic tapered fiber fabrications. An enhanced fiber tapering system based on a novel heat source and an innovative monitoring method have been developed. The novel heat source is a low-cost ceramic housed electric furnace (CHEF). The innovative monitoring method is based on the frequency-domain optical transmission signal from the fiber that is being tapered. The enhanced fiber tapering system can allow highly repeatable fabrication of adiabatically tapered fibers. 2) A lossy mode resonance (LMR) sensor enabled by SnO2 coating on a novel specially shaped fiber design has been developed. The developed LMR sensor has a D-shape fiber tip with SnO2 coating. It has the capability of relative humidity and moisture sensing. The fiber-tip form factor can allow the sensor to be used like a probe and be inserted into/removed from a tight space. 3) Specially shaped tapered fibers with novel designs have been developed for integrated photonic and microfluidic applications. Two novel specially tapered fibers, the tapered fiber loop and the tapered fiber helix have been developed. The tapered fiber loop developed in this work has two superiority that differentiated itself from previous works: a) the mechanical stability of the tapered fiber loop in this work is significantly better. b) the tapered fiber loops in this work can achieve a diameter as small as 15 ?m while still have a high intrinsic optical quality factor of 32,500. The tapered fiber helix developed in this work has a 3D structure that allows it to efficiently deliver light to locations out of the plane defined by its two regular fiber arms. Applications of the tapered fiber helices in both integrated photonic device characterizations and microparticle manipulations have been demonstrated. 4) Developed an acrylic-tape hybrid microfluidic platform that can allow function reconfiguration and optical fiber integration. A low-cost, versatile microfluidic platform based on reconfigurable acrylic-tape hybrid microfluidic devices has been developed. To the best of the author’s knowledge, this is the first time that the fabrication method of sealing the acrylic channel with a reconfigurable functional tape has been demonstrated. The tape-sealing method is compatible with specially shaped fiber integrations.