The soft robotics field is developing rapidly and is poised to have a wide impact in a variety of applications. Soft robots have intrinsic compliance, offering a number of benefits as compared to traditional rigid robots. Compliance can provide compatibility with biological systems such as the human body and can provide some benefits for human safety and control. Further research into soft robots can be advanced by further development of pneumatic actuators. Pneumatic actuators are a good fit for exoskeleton robots because of their light weight, small size, and flexible materials. This is because a wearable robot should be human friendly, therefore, it should be light weight, slim, powerful, and simple. In this paper, a novel pneumatic artificial muscle using soft materials including integrated electronics for wearable exoskeletons is proposed. We describe the design, fabrication, and evaluation of the actuator, as well as the manufacturing process used to create it. Compared to traditional pneumatic muscle actuators such as the McKibben actuator and new soft actuators that were recently proposed, the novel actuator overcomes shortcomings of prior work. This is due to the actuator's very high contraction ratio that can be controlled by the manufacturing process. In this paper, we describe the design, fabrication, and evaluation of a novel pneumatic actuator that can accommodate integrated electronics for displacement and pressure measurements used for data analysis and control. The desired performance characteristics for the actuator were 100 ~ 400N at between 35kPa and 105kPa, and upon testing we found almost 120 ~ 300N which confirms that these actuators may be suitable in soft exoskeleton applications with power requirements comparable to rigid exoskeletons. Furthermore, a novel soft pneumatic elbow exoskeleton based on the pneumatic actuator concept and manufacturing process is presented. Each structure is designed and manufactured with all fabric. The distally-worn structure is only 300g, which is light weight for an arm exoskeleton, and the design is simple, leading to a low materials cost. / Master of Science / The soft robotics field is developing rapidly and is poised to have a wide impact in a variety of applications. The soft robotics is the specific field of robotics, which deals with flexible materials and different geometry in contrast to general robots made by rigid materials. Therefore, soft robots have intrinsic compliance, offering a number of benefits as compared to traditional rigid robots. Compliance can provide compatibility with biological systems such as the human body and can provide some benefits for human safety and control. Further research into soft robots can be advanced by the further development of pneumatic actuators. Pneumatic actuators are a good fit for exoskeleton robots because of their light weight, small size, and flexible materials. This is because a wearable robot should be human-friendly, therefore, it should be light weight, slim, powerful, and simple. In this paper, a novel pneumatic artificial muscle using soft materials for wearable exoskeletons is proposed. We describe the design, fabrication, and evaluation of the actuator, as well as the manufacturing process used to create it and its electronic system for data analysis and control. Furthermore, a novel soft pneumatic elbow exoskeleton based on the pneumatic actuator concept and manufacturing process is presented. Each structure is designed and manufactured with all fabric. The distally-worn structure is only 300g, which is light weight for an arm exoskeleton, and the design is simple, leading to a low materials cost.

Textiles of today are materials with applications in almost all our activities. We wear clothes all the time and we are surrounded with textiles in almost all our environments. The integration of multifunctional values in such a common material has become a special area of interest in recent years. Smart Textile represents the next generation of textiles anticipated for use in several fashion, furnishing and technical textile applications. The term smart is used to refer to materials that sense and respond in a pre-defined manner to environmental stimuli. The degree of smartness varies and it is possible to enhance the intelligence further by combining these materials with a controlling unit, for example a microprocessor. As an interdisciplinary area Smart Textile includes design spaces from several areas; the textile design space, the information technology design space and the design space of material science. This thesis addresses how Smart Textiles affect the textile design space; how the introduction of smart materials and information technology affects the creation of future textile products. The aim is to explore the convergence between textiles, smart materials and information technology and to contribute to providing a basis for future research in this area. The research method is based on a series of interlinked experiments designed through the research questions and the research objects. The experiments are separated into two different sections: interactive textile structures and health monitoring. The result is a series of basic methods for how interactive textile structures are created and a general system for health monitoring. Furthermore the result consists of a new design space, advanced textile design. In advanced textile design the focus is set on the relation between the different natures of a textile object: its physical structure and its structure in the context of design and use.

Soft robotic systems have recently been considered as a new approach that is in principle better suited for tasks where safety and adaptability are important. That is because soft materials are inherently compliant and resilient in the event of collisions. They are also lightweight and can be low-cost; in general, soft robots have the potential to achieve many tasks that were not previously possible with traditional robotic systems. In this paper, we propose a new manufacturing process for creating multi-chambered pneumatic actuators and robots. We focus on using fabric as the primary structural material, but plastic films can be used instead of textiles as well. We introduce two different methods to create layered bellows actuators, which can be made with a heat press machine or in an oven. We also describe origami-like actuators with possible corner structures. Moreover, the fabrication process permits the creation of soft and soft/rigid hybrid robotic systems, and enables the easy integration of sensors into these robots. We analyze various textiles that are possibly used with this method, and model bellows actuators including operating force, restoring force, and estimated geometry with multiple bellows. We then demonstrate the process by showing a bellows actuator with an embedded sensor and other fabricated structures and robots. We next present a new design of a multi-DOF soft/rigid hybrid robotic manipulator. It contains a revolute actuator and several roll-pitch actuators which are arranged in series. To control the manipulator, we use a new variant of the piece-wise constant curvature (PCC) model. The robot can be controlled using forward and inverse kinematics with embedded inertial measurement units (IMUs). A bellows actuator, which is a subcomponent of the manipulator, is modeled with a variable-stiffness spring, and we use the model to predict the behavior of the actuator. With the model, the roll-pitch actuator stiffnesses are measured in all directions through applying forces and torques. The stiffness is used to predict the behavior of the end effector. The robotic system introduced achieved errors of less than 5% when compared to the models, and positioning accuracies of better than 1cm. / Doctor of Philosophy / Future robotic systems are expected to deal with many tasks in real-world environments. The natural environment is highly unpredictable and unstructured, making manipulation and locomotion challenging for robots. Robots need to rely on adaptability, reconfigurability, and safety. Soft robotic systems have recently been considered as a new approach that is in principle better suited for tasks where safety and adaptability are important. That is because soft materials are inherently compliant and resilient in the event of collisions. They are also lightweight and can be low-cost; in general, soft robots have the potential to achieve many tasks that were not previously possible with traditional robotic systems. In this paper, we propose a new manufacturing process for creating multi-chambered pneumatic actuators and robots. We focus on using fabric as the primary structural material, but plastic films can be used instead of textiles as well. We introduce two different methods to create layered bellows actuators, which can be made with a heat press machine or household iron, or in an oven. We also describe origami-like actuators with possible corner structures. Moreover, the fabrication process permits the creation of soft and soft/rigid hybrid robotic systems, and enables the easy integration of sensors into these robots. We analyze various textiles that can be used with this method, and make models of bellows actuators including their operating force, restoring force, and estimated geometry with multiple bellows. We then demonstrate the process by showing a bellows actuator with an embedded sensor and other fabricated structures and robots. We next present a new design of a multi-DOF soft/rigid hybrid robotic manipulator. It contains a revolute actuator and several roll-pitch actuators which are arranged in series. To control the manipulator, we use a new variant of the piece-wise constant curvature (PCC) model. The robot can be controlled using forward and inverse kinematics with embedded inertial measurement units (IMUs). A bellows actuator, which is a subcomponent of the manipulator, is modeled with a variable-stiffness spring, and we use the model to predict the behavior of the actuator. With the model, the roll-pitch actuator stiffnesses are measured in all directions through applying forces and torques. The stiffness is used to predict the behavior of the end effector.