Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

Le cadre général de la thèse concerne la valorisation sous forme de production d'énergie électrique de la chaleur présente à quelques kilomètres de profondeur (3 à 5 km), en général dans des milieux peu perméables et fracturés. Notre objectif principal est d'étudier le phénomène des microséismes induits relativement au refroidissement, en nous basant sur une expérience de terrain de longue durée, menée sur le site de Rosemanowes (Cornwall, UK). Pour cela nous avons procédé à la mise en place d'un outil de calcul, FRACAS, capable de simuler ce phénomène en introduisant une approche à double milieu thermique pour mieux simuler le refroidissement du réservoir dû à l'injection de fluide à long terme, responsable des nouveaux mécanismes de ruptures dus à la traction de la roche. Dans ce contexte nous avons introduit un nouvel algorithme pour prendre en compte les manifestations d'instabilités, un mécanisme de « stick-slip » avec prise en compte d'une friction statique et d'une friction dynamique. La possibilité d'induire des microséismes est ensuite étudiée à partir des données issues d'un site particulier, avec deux modèles 3D proposant des approches géométriques différentes, un modèle déterministe et un modèle stochastique, dont les propriétés géométriques et physiques ont été tirées des observations et travaux antérieurs effectués sur ce site de Rosemanowes. La simulation thermo-hydro-mécanique (THM) du modèle déterministe nous a permis de modéliser les échanges thermiques en régime transitoire dans le réservoir formé par le système de forages RH12/RH15 et d'estimer un ordre de grandeur des tractions d'origine thermique. Pour mieux étudier l'effet induit par la contraction des blocs de roche dans le temps nous utilisons le modèle 3D stochastique dont l'objectif principal est de simuler de façon plus réaliste la progression dans l'espace les ruptures en cisaillement. Avec ce modèle nous avons constaté l'apparition différée d'une activité et l'effet d'un cycle de pulses de pression, ce qui suggère un moyen d'atténuer les fortes magnitudes potentielles des ruptures en cisaillement dues au refroidissement. / The general framework of our research deals with the development of geothermal energy for electricity production using the heat stored in geological formations at depths ranging in 3 to 5 km, Generally the environment is poorly permeable and fractured. Our main objective is to study the phenomenon of induced micro-earthquakes in relation to the cooling of the rock. The work is based on field experiences including long duration tests, conducted on the Rosemanowes site (Cornwall, UK). For this, we proceeded to the development of a calculation tool, FRACAS, able to simulate this phenomenon by introducing a dual thermal approach to better simulate the cooling of the reservoir due to long term fluid injections, which might be responsible for new failure mechanisms due to the induced tractions. In this context, we introduced a new algorithm to describe shear in stabilities, a mechanism of "stick-slip" type with the consideration of static/dynamic friction coefficients. The possibility of inducing micro-seismicity is then studied using the in situ data base, with two 3D models offering different geometric approaches, a deterministic model and a stochastic model whose geometrical and physical properties were obtained from observations and previous work on this Rosemanowes site. The Thermo-Hydro-Mechanical (THM) simulation using the deterministic model has allowed us to calibrate the transient heat transfer in the reservoir formed by the drilling system RH12/RH15 and to give an estimate of tensile stress of thermal origin. To better study the effect induced by the contraction of the rock during time, we use the stochastic 3D model whose main objective is to simulate a more realistic spatial migration of shear ruptures. With this model we found a delayed onset of shear activity and discuss the effect of pressure step tests. The results suggest a way to mitigate the potential impact of shear ruptures due to cooling.

Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

Durant les différentes phases du stockage profond des déchets radio-actifs exothermiques (excavation, exploitation) jusqu'à la fermeture définitive, la roche hôte sera soumise à des sollicitations mécaniques, hydriques et thermiques couplées. Afin de connaître et de modéliser le comportement à court et long terme des dispositifs de stockage, une investigation approfondie du comportement de la roche est nécessaire afin de compléter les données existantes. C'est dans ce but que cette étude du comportement thermo-hydro-mécanique de la formation argileuse du Callovo-Oxfordien (COx) considérée par l'ANDRA comme roche hôte potentielle, a été développée. Dans un premier temps le comportement en compression–gonflement de l'argilite du COx a été étudié par la réalisation d'un programme d'essais oedométriques haute pression. Les résultats, interprétés en termes de couplage endommagement-gonflement, ont montré que l'ampleur du gonflement était lié à la densité de fissuration engendrée lors de la compression. Dans un second temps, le comportement hydromécanique et thermo-hydro-mécanique de l'argilite saturée sous une contrainte moyenne proche de l'in-situ a été étudié à l'aide de cellules à faible chemin de drainage (10 mm), dont une cellule isotrope et une cellule triaxiale à cylindre creux avec mesures locales d'un type nouveau. Ces appareils ont permis de résoudre deux problèmes difficiles typiques des argilites de très faible perméabilité : i) une saturation préalable correcte, attestée par de bonnes valeurs du coefficient de Skempton et ii) de bonnes conditions de drainage. Les paramètres caractéristiques du comportement de l'argilite à température ambiante (coefficients de Skempton et de Biot, compressibilité drainée et non-drainée) ont été déterminés à partir d'essais de compression isotrope qui ont également confirmé l'isotropie transverse du matériau. La cohérence des paramètres obtenus a été vérifiée dans un cadre poro-élastique saturé. Deux aspects du comportement thermo-hydro-mécanique de l'argilite du COx ont été étudiés à l'aide d'essais de chauffage et de compression volumique en température (80°C) : les effets de la température sur le comportement intrinsèque de l'argilite et le phénomène de pressurisation thermique. Un essai de chauffage drainé sous contrainte in-situ a mis en évidence, apparemment pour la première fois, un comportement plastique contractant de l'argilite (comme les argiles normalement consolidées), non pris en compte dans les modélisations thermo-élastiques actuelles des systèmes de stockage profond. Un autre élément nouveau et important observé est l'augmentation de la compressibilité avec la température, à la différence des argiles. L'étude de la pressurisation thermique (engendrée par la faible perméabilité de l'argilite et la forte différence entre les coefficients de dilatation thermique de l'eau et de la phase solide), a été réalisée à l'aide d'essais de chauffage non drainés, suite à une analyse détaillée des effets perturbateurs du système de mesure lors de variations de pression et de température (peut-être à considérer également dans les mesures in-situ). Le coefficient de pressurisation thermique s'est révélé être très sensible aux variations de température et de contrainte, il diminue de 0,14 à 0,1 MPa/°C entre 25 et 80°C. La nature des différentes réponses hydro-mécaniques et thermo-hydro-mécaniques obtenues au cours de ce travail permettront une interprétation et une modélisation plus précises du comportement du massif d'argilite autour des galeries, dans des zones qui sont pour la plupart saturées, sauf à proximité immédiate des galeries (quelques décimètres) / During the different phases of the exothermic radioactive waste deep disposal (excavation, operation) and after permanent closure, the host rock is submitted to various coupled mechanical, hydraulic and thermal phenomena. Hence, a thorough investigation of the thermo-hydro-mechanical behaviour of the rock is necessary to complete existing data and to better understand and model the short and long term behaviour of the Callovo-Oxfordian (COx) clay formation in Bure (Meuse/Haute-Marne - M/HM), considered by ANDRA as a potential host rock in France.In this work, the compression – swelling behaviour of the COx claystone was first investigated by carrying out a series of high-pressure oedometric tests. The results, interpreted in terms of coupling between damage and swelling, showed that the magnitude of swelling was linked to the density of the fissures created during compression. In a second step, the hydromechanical and thermo-hydro-mechanical behaviour of the saturated claystone under a mean stress close to the in situ one were investigated by using two devices with short drainage path (10 mm), namely a isotropic cell and a newly designed hollow cylinder triaxial cell with local displacement measurements. These devices helped to solve two majors problems related to testing very low permeability materials : i) a satisfactory previous sample saturation (indicated by good Skempton values) and ii) satisfactory drainage conditions. Some typical constitutive parameters (Skempton and Biot's coefficients, drained and undrained compressibility coefficients) have been determined at ambient temperature through isotropic compression tests that also confirmed the transverse isotropy of the claystone. The consistency of the obtained parameters has been checked in a saturated poroelastic framework. Two aspects of the thermo-hydro-mechanical behaviour of the COx claystone have then been investigated through different heating tests and through drained and undrained isotropic compression tests at elevated temperature (80°C) : the effects of temperature on the behaviour of claystone and thermal pressurization. A drained heating test under in-situ stress conditions evidenced, probably for first time, a plastic contractant response of the claystone (like normally consolidated clays), a feature not considered in the presently conducted numerical modelling of deep disposal systems. Another new important observed feature is the increase in drained compressibility of the COx claystone with temperature, not observed in clays. The investigation of thermal pressurization (caused by the low claystone permeability and by the significant difference in thermal expansion between water and the solid phase) has been carried out by means of undrained heating tests, after a detailed analysis of the major effects of the measurement system (which should perhaps be also analyzed when performing in-situ measurements). The thermal pressurization coefficient appeared to be quite sensitive to changes in temperature and stress, it decreased between 0.14 and 0.1 MPa/°C between 25 and 80°C. It is believed that the different thermo-hydro-mechanical volumetric responses obtained here allow a better interpretation and modelling of the behaviour of the claystone formation around the galleries in areas that are mostly saturated, except close to the galleries (a few decimetres)