Simulating wave propagation in microstrip lines with Gyrotropic magnetic substrate is considered in this thesis. Since the static internal field distribution has an important effect on the device behavior, accurate determination of the internal fields are considered as well. To avoid the losses at microwave frequencies it is assumed that the magnetic substrate is saturated in the direction of local internal field. An iterative method to obtain the magnetization distribution has been developed. It is applied to a variety of nonlinear nonuniform magnetic material configurations that one may encounter in the design stage, subject to a nonuniform applied field. One of the main characteristics of the proposed iterative method to obtain the static internal field is that the results are supported by a uniqueness theorem in magnetostatics. The series of solutions Mn,Hn, where n is the iteration number, minimize the free Gibbs energy G(M) in sequence. They also satisfy the constitutive equation M = χH at the end of each iteration better than the previous one. Therefore based on the given uniqueness theorem, the unique stable equilibrium state M is determined. To simulate wave propagation in the Gyrotropic magnetic media a new FDTD formulation is proposed. The proposed formulation considers the static part of the electromagnetic field, obtained by using the iterative approach, as parameters and updates the dynamic parts in time. It solves the Landau-Lifshitz-Gilbert equation in consistency with Maxwell’s equations in time domain. The stability of the initial static field distribution ensures that the superposition of the time varying parts due to the propagating wave will not destabilize the code. Resonances in a cavity filled with YIG are obtained. Wave propagation through a microstrip line with YIG substrate is simulated. Magnetization oscillations around local internal field are visualized. It is proved that the excitation of magnetization precession which is accompanied by the excitation of magnetostatic waves is responsible for the gap in the scattering parameter S12. Key characteristics of the wide microstrip lines are verified in a full wave FDTD simulation. These characteristics are utilized in a variety of nonreciprocal devices like edgemode isolators and phase shifters.

High-Pressure, High-Temperature (HPHT) pressure gauges are commonly used in oil wells for pressure transient analysis. Mathematical models are used to relate input perturbation (e.g., flow rate transients) with output responses (e.g., pressure transients), and subsequently, solve an inverse problem that infers reservoir parameters. The indispensable use of pressure data in well testing motivates continued improvement in the accuracy (quality), sampling rate (quantity), and autonomy (lifetime) of pressure gauges. This body of work presents improvements in three areas of high-pressure, high-temperature quartz memory gauge technology: calibration accuracy, multi-tool signal alignment, and tool autonomy estimation. The discussion introduces the response surface methodology used to calibrate gauges, develops accuracy and autonomy estimates based on controlled tests, and where applicable, relies on field gauge drill stem test data to validate accuracy predictions. Specific contributions of this work include: - Application of the unpaired sample t-test, a first in quartz sensor calibration, which resulted in reduction of uncertainty in gauge metrology by a factor of 2.25, and an improvement in absolute and relative tool accuracies of 33% and 56%, accordingly. Greater accuracy yields more reliable data and a more sensitive characterization of well parameters. - Post-processing of measurements from 2+ tools using a dynamic time warp algorithm that mitigates gauge clock drifts. Where manual alignment methods account only for linear shifts, the dynamic algorithm elastically corrects nonlinear misalignments accumulated throughout a job with an accuracy that is limited only by the clock's time resolution. - Empirical modeling of tool autonomy based on gauge selection, battery pack, sampling mode, and average well temperature. A first of its kind, the model distills autonomy into two independent parameters, each a function of the same two orthogonal factors: battery power capacity and gauge current consumption as functions of sampling mode and well temperature -- a premise that, for 3+ gauge and battery models, reduces the design of future autonomy experiments by at least a factor of 1.5.

A distributed sensor using an optical fiber for detecting and locating intruders over long perimeters (>10 km) is described. Phase changes resulting from either the pressure of the intruder on the ground immediately above the buried fiber or from seismic disturbances in the vicinity are sensed by a phase-sensitive optical time-domain reflectometer (φ−OTDR). Light pulses from a cw laser operating in a single longitudinal mode and with low (MHz/min range) frequency drift are injected into one end of the single mode fiber, and the backscattered light is monitored with a photodetector. In laboratory tests with 12 km of fiber on reels, the effects of localized phase perturbations induced by a piezoelectric fiber stretcher on φ−OTDR traces were characterized. In field tests in which the sensing element is a single mode fiber in a 3-mm diameter cable buried in an 8 to 18 inch deep, 4 inch wide trench in clay soil, detection of intruders on foot up to 15 ft from the cable line was achieved. In desert terrain field tests in which the sensing fiber is in a 4.5-mm diameter cable buried in a 1 ft deep, 2.5 ft wide trench filled with loose sand, high sensitivity and consistent detection of intruders on foot and of vehicles traveling down a road near the cable line was realized over a cable length of 8.5 km and a total fiber path of 19 km in real time. In a final series of field tests in clay soil, phase changes produced by the steps of a person walking up to 15 ft away from the buried cable were observed, and vehicles traveling at 10 mph were consistently detected up to 300 ft away. Based on these results, this technology may be regarded as a candidate for providing low-cost perimeter security for nuclear power plants, electrical power distribution centers, storage facilities for fuel and volatile chemicals, communication hubs, airports, government offices, military bases, embassies, and national borders.

As a comparative study, the global performance of two cases for a floating harbor system are researched by numerical analysis and compared with results from experiments: one is a two-body case such that a floating quay is placed next to a fixed quay, a normal harbor, and the other is a three-body case such that a container ship is posed in the middle of the floating quay and the fixed quay. The numerical modeling is built based on the experimental cases. Mooring system used in the experiments is simplified to sets of linear springs, and gaps between adjacent bodies are remarkably narrow as 1.3m~1.6m with reference to large scales of the floating structures; a water plane of the fixed quay is 480m×160m, and the ship is 15000 TEU (twenty-foot equivalent unit) class. With the experiment-based models, numerical analysis is implemented on two domains: frequency domain using a three dimensional constant panel method, WAMIT, and time domain using a coupled dynamic analysis program of moored floating structures, CHARM3D/HARP. Following general processes of the two main tools, additional two calibrations are implemented if necessary: revision of external stiffness and estimation of damping coefficients. The revision of the external stiffness is conducted to match natural frequency of the simulation with that of the experiment; to find out natural frequencies RAO comparison is used. The next, estimation of damping coefficients is carried out on time domain to match the responses of the simulation with those of the experiment. After optimization of the numerical analysis, a set of experimental results from regular wave tests is compared with RAO on frequency domain, and results from an irregular wave test of the experiment are compared with response histories of simulation on time domain. In addition, fender forces are compared between the simulation and experiment. Based on response histories relative motions of the floating quay and container ship are compared. And the floating harbor system, the three-body case, is compared with a conventional harbor system, a fixed quay on the portside of the container ship, in terms of motions of the container ship. As an additional simulation, the three-body case is investigated on an operating sea state condition. From the present research, the experimental results are well matched with the numerical results obtained from the simulation tools optimized to the experiments. In addition, the floating harbor system show more stable motions of the container ship than the conventional harbor system, and the floating harbor system in the operating sea state condition have motions even smaller enough to operate in term of relative motions between the floating quay and the container ship.

With the trends of fast edge rates, high clock frequencies, and low voltage levels for the high-speed digital computer systems, the ground bounce noise (GBN) or simultaneously switching noise (SSN) on the power/ground planes is becoming one of the major challenges for designing the high-speed circuits. In order to analyze the impact of the GBN on signal integrity (SI) and electromagnetic interference (EMI), an accurate and efficient modeling approach that considers the active devices and passive interconnects is required. This thesis focuses on two points. One is developing modeling approaches for analyzing the GBN effects, and the other is proposing solutions to reduce it. First, based on the FDTD algorithm several efficient modeling approaches including equivalent current-source method (ECSM), Kirchoff surface integral representation (KSIR), and slot-corrected 2D-FDTD are developed. After that, a power/ground-planes design for efficiently eliminating the GBN in high-speed digital circuits is proposed by using low-period coplanar electromagnetic bandgap (LPC-EBG) structure. Its extinctive behaviors of low radiation and broadband suppression of the GBN is demonstrated numerically and experimentally. Good agreements are seen.

The dissertation focuses on the analysis and design for the new fiber-optic passive components based on the photonic-crystal-fiber (PCF). The vector boundary element method (VBEM) and the finite-difference time-domain (FDTD) method are employed to the propagation characteristics of PCF components. A novel octagonal microstructured fiber (OMF) with eight air-holes in the first ring has been proposed. The OMF has significantly wider wavelength range for single-mode operation, more circular-like field distribution, and less confinement loss. In addition, a novel compact polarization beam splitter (PBS) based on the twin-elliptical-core PCF (TEC-PCF) has also been proposed. It behaves with high extinction ration and broad bandwidth with significantly short splitter length. The design concept and the coupling mechanism are presented in this dissertation based on the normal-mode coupling theory and VBEM.

First, one of the purposes of this thesis is to estimate the complete crosstalk effects including the package and the pads on the surface acoustic wave (SAW) substrate. A new approach based on finite-difference time-domain (FDTD) with equivalent current source method is applied. Two kinds of patterns of one-port SAW resonators with the same package structure and inter-digital transducer (IDT) design are studied. Verification with the measurement results shows that our method is able to obtain good agreement and be used to observe the influence from the SAW pattern. Second, the equivalent current source method is extended to model the excitation of human-body¡¦s electrostatic discharge (ESD) situations. The efficiencies of sacrificial electrodes are also discussed. Finally, a novel sacrificial electrode with fractal to protect SAW devices from ESD break is proposed. Comparing with traditional electrode, the simulation results show that fractal can improve the protective efficiency greatly. Finally, a novel analysis model that can be used to analyze and optimize the impedance of an RFID transponder integrated circuit (IC) which uses backscatter encoding based on simultaneously maintaining the BER of the reader and maximizing the received power of the transponder IC is proposed. The analysis method utilizes mapping from signal constellation of the backscattered signal to the Smith chart to relate the two parameters. Given the system specification and characteristics of the reader and transponder antennas, the optimum impedances of transponder IC for binary communication system can be easily designed by using this model.

This thesis focuses on the modeling and solutions of the simultaneous switching noise (SSN) problems in the power delivery networks (PDN) of high-speed digital circuit packages. An efficient numerical approach based on two-dimension (2D) finite-difference time-domain (FDTD) method combined with the lumped circuit model of the interconnection is proposed to model the PDN of a package and PCB. Based on this approach, the mechanism of noise coupling between package and PCB can be analyzed. In addition, a novel photonic crystal power layer (PCPL) design for the PDN of the package or PCB is proposed to suppress the SSN. The periodic High-Dk material is embedded into the substrate layer between the power and ground planes. Both modeling and measurement demonstrate the PCPL can form a wide stopband well with excellent suppression of the SSN propagation in the substrate and the corresponding electromagnetic interference (EMI).

The goal of this thesis is to describe development of compact terahertz time-domain spectrometer driven by a mode-locked Ti:Sapphire laser. The terahertz radiation was generated by photoconductive antenna method and detected by electro-optic detection method. In this thesis, several terahertz generation and detection method, working principle of terahertz time-domain spectroscopy and its applications are discussed. We mainly focused on working principle of terahertz time-domain spectroscopy and characterization of detected terahertz power using electro-optic detection method.

The objective of this research is to present a set of powerful simulation, design, and characterization tools suitable for studying novel nanophotonic devices. The simulation tools include a three-dimensional finite-difference time-domain code adapted for parallel computing that allows for a wide range of simulation conditions and material properties to be studied, as well as a semi-analytical Green's function-based complex mode technique for studying loss in photonic crystal waveguides. The design tools consist of multifunctional photonic crystal-based template that has been simulated with nonlinear effects and measured experimentally, and planar slab waveguide structure that provides highly efficient second harmonic generation is a chip-scale device suitable for photonic integrated circuit applications. The characterization tool is composed of a phase-sensitive measurement system using a lock-in amplifier and high-precision optical stages, suitable for probing the optical characteristics of nanoscale devices. The high signal-to-noise ratio and phase shift data provided by the lock-in amplifier allow for accurate transmission measurements as well as a phase spectrum that contains information about the propagation behavior of the device beyond what is provided by the amplitude spectrum alone.