The diploma thesis deals with the issue of bridge strustures, especially their diagnostics and evaluation. The work consists of two parts, theoretical and practical. The theoretical part deals with the basic description and division of bridge structures, brigde inspections and test methods, especially those that were used in the thesis during bridge inspections. The practical part includes a visual inspection of two bridges, their description, detection of faults and defects and their documentation. In the practical part, the basic maretial characteristics of concrete bridges were determined, the condition of structures was assessed and a proposal for the elimination of failures and defects was developed. In the end, the work deals with the evaluation of both bridges.

The theoretical part of the diploma thesis searches the production of Construction and demolition waste and their subsequent transformation into the final recyclate and its possible use in roads. Attention is focused on the use of mixed recycled material into subgrade of the pavement and the characteristics of tests that must be performed before its used to the road. The next chapters pai attention to the problematic properties of recyclates, foreign experience with the use of mixed recyclate in Construction and the possibilities of its development. The practical part verifies the suitability of mixed recycled material into subgrade of the pavement using laboratory tests. The tests are performer on individual mixtures of mixed recycled material with cement, blast furnace slag or cement dust in various percentages. The results are then compared and it is evaluated which mixtures show the best properties. Part of the practical part is also the economic evaluation of these mixtures against commonly used materials.

Předložená magisterská práce se zabývá možným použitím vitrifikovaného lignitového lóžového popele jako náhrada slinku v kompozitních cementech. Byly zkoumány vlivy přidaného vitrifikovaného lóžového popele, jeho jemnosti, alkalických roztoků a jejich koncentrací. Byly připraveny kompozitní cementy v souladu s normou DIN EN 197 – 1. V těchto cementech bylo nahrazeno 30 % slinku vitrifikovaným lóžovým popelem. Konkrétně byly připraveny kompozitní cementy s vitrifikovaným lóžovým popelem o jemnosti 5549 cm2/g a 8397 cm2/g. Dále byly přidány alkalické roztoky hydroxidů a síranů vždy o dvou různých koncentracích, za účelem stimulace pucolánové a/nebo geopolymerní reakce. Mechanické vlastnosti připravených vzorků byly charakterizovány mechanickým testováním na prizmách s rozměry 40×40×160 mm, jak je specifikováno v normě DIN EN 196 – 1. Byla provedena nedestruktivní měření dynamického elastického modulu a destruktivní testovaní na pevnosti v tlaku a v ohybu. Distribuce velikosti částic a chemická analýza vstupních materiálů byla vykonána pomocí laserové granulometrie a rentgenové fluorescence. U zatvrdlých kompozitů bylo dále zkoumáno po 2 a 28 dnech hydratace fázové složení s využitím metody rentgenové difrakce a mikrostruktura s využitím skenovací elektronové mikroskopie. Výsledky ukázaly, že mechanické vlastnosti jsou nezávislé na množství přidaných alkálií stejně jako na jemnosti přidaného vitrifikovaného lóžového popele. Nicméně, znatelně nižší mechanické pevnosti byly pozorovány pro vzorky, které byly aktivovány hydroxidy, pravděpodobně kvůli brzké tvorbě silikátového hydrogelu. Vzorky aktivované sírany nedosáhly pevností jako referenční malta.

In my master's tehsis I'm dealin with the methods used for non-invasive blood pressure measurement. For realization of a virtual blood pressure meter in LabVEW I have chosen the oscillometric method. Algorithm determining systolic and diastolic blood pressure is based on the relatively easy detection of maximum amplitude oscillations (corresponds with a mean arterial pressure), when thelimiting valuesof blood pressure are in a specific ratio with a maximum amplitude of oscillation. In LabVIEW was solved loading of signal from the measure card and processing pressure curve into a form suitable for the detection of the peak oscillations. The program calculates the limits of arterial pressure and mean heart rate too. Linking the virtual device with the blood pressure sensor Vernier BPS-BTA then makes up komplex for capturing the blood pressure via oscillatory method.

First part of this thesis is a theoretical essay which deals with the basics of the variable pressure scanning electron microscope, includes detection of secondary electrons with a view to a scintillation detector. The first applied part of the thesis is focused on prediction, measuring and setting-up optional working parley in vacuum electrodes scintillation detector system, with a stress small diameter hole in screenings C1 and C2. Second applied part was verify a change of working distance between sample and detector in consequence to optional solution for another work.

The master thesis dealing with problematic about durability of concrete, with use of recycled concrete and addition of silica additions. Predominant for resistance of concrete constructions is surface layer, through which aggressive gasses and liquids penetrate from surrounding environment. The most important indicator of concrete durability is ability of surface layer transmissions of aggressive substants. In experimental part will be defined the actual state of surface layer by normal testing methods. The transmissions of surface layer will be tested on concrete cubes. Tests for transmissions of air (method TORRENT), of water (method ISAT), of acid gases (dept of carbonation by quick test in 98% CO2) will be carried out and also strength tests. Assessment of positive or negative influence of additions and amount of cement on durability and mechanical properties of concrete will be discussed in conclusion.

The topic of this master's thesis is the development of composite materials based on inorganic binders for use in extreme conditions. It means especially geopolymeric or alkali activated materials (AAM) based composites. The theoretical part of this thesis summarizes knowledges about the development and use of alkali-activated materials, their structure and mechanisms of their formation. It also deals with the applicable raw materials for AAM and their exciters, which are in particular water glass and sodium hydroxide. There also have been a summary of the effects of high temperatures and chemicals on the mechanical properties of AAM and the requirements of standard EN 1504-3 for repairing materials. The task of the practical part was to develop a repair mortar for concrete structures based on AAM so that its production was as simple as possible, ie one-component materials. Gradually six recipes have been develeoped. Test specimens made from these recipes have been putted to selected tests according to the requirements of ČSN EN 1504-3.

In the theoretical part of the thesis are generally characterized hydraulically bound mixtures, their types, classification systems, manufacturing technology and the laying. There are also described experiences from abroad with the use secondary and recycled materials in hydraulically bound mixtures. The practical part deals with the experimental verification of the possibility of the use of secondary materials in hydraulically bound mixtures in construction of road infrastructure. In road laboratory Institute of road structures Brno university of technology was the five proposed mixtures, an assessment of their parameters with regard to the possibility of using these mixtures in the road sub-base layers. The work is also aimed at comparison of results elasticity modules reached laboratory testing and experimental measurements on road polygon.

The work is divided into two parts. The first part deals with the description of unbound and bound base layers and their comparison. Furthermore is presented the description of the recycled concrete, its properties, production, improvement and issues. International experiences with recycled concrete technology are described as well. The practical part is focused on laboratory testing of concrete recycled material taken from the highway D1. The aim of this part is to determine whether the concrete can be recycled back into unbound or bound base layers and concrete casing.

The master´s thesis focuses on high-alumina refractory materials used mainly in aluminia metallurgy. Teoretical part of this thesis is aimed at distribution of refractory materials, possibilities of its production and raw material basis. Characteristic properties are described as well as application possibilities in aluminium technology. In final part of this thesis experimental data are evaluated to obtain physical, mechanical, chemical properties of high-alumina refractory materials. Those are used for economical optimalization of raw materials.