Thesis (PhD (Electrical Engineering))--Cape Peninsula University of Technology, 2019 / This dissertation presents a concept for a compact, low-profile, integrated solar panel antenna for use on small satellites in low Earth orbit. To date, the integrated solar panel antenna design approach has primarily been, patch (transparent or non-transparent) and slot radiators. The design approach presented here is proposed as an alternative to existing designs. A prototype, comprising of an optically transparent rectangular dielectric resonator was constructed and can be mounted on top of a solar panel of a Cube Satellite. The ceramic glass, LASF35 is characterised by its excellent transmittance and was used to realise an antenna which does not compete with solar panels for surface area. Currently, no closed-form solution for the resonant frequency and Q-factor of a rectangular dielectric resonator antenna exists and as a first-order solution the dielectric waveguide model was used to derive the geometrical dimensions of the dielectric resonator antenna. The result obtained with the dielectric waveguide model is compared with several numerical methods such as the method of moments, finite integration technique, radar cross-section technique, characteristic mode analysis and finally with measurements. This verification approach was taken to give insight into the resonant modes and modal behaviour of the antenna. The interaction between antenna and a triple-junction gallium arsenide solar cell is presented demonstrating a loss in solar efficiency of 15.3%. A single rectangular dielectric resonator antenna mounted on a ground plane demonstrated a gain of 4.2 dBi and 5.7 dBi with and without the solar cell respectively. A dielectric resonator antenna array with a back-to-back Yagi-Uda topology is proposed, designed and evaluated. The main beam of this array can be steered can steer its beam ensuring a constant flux density at a satellite ground station. This isoflux gain profile is formed by the envelope of the steered beams which are controlled using a single digital phase shifter. The array achieved a beam-steering limit of ±66° with a measured maximum gain of 11.4 dBi. The outcome of this research is to realise a single component with dual functionality satisfying the cost, size and weight requirements of small satellites by optimally utilising the surface area of the solar panels.

This dissertation research presents a comprehensive study to answer the question of “Can it be possible to integrate a high gain optically transparent antenna array directly on top of solar cells?”. The answer to such question is extremely important in space exploration where very small satellites have been extensively employed. Due to their small mass and size, those small satellites create challenges for one to mount the antennas, and the challenge is further increased when a high gain antenna is need for more communication capacity. Based on feasibility studies, the dissertation concludes that it is possible to do such an integration, and then proceeds to present the approaches for design and integration. On the element level, the thesis presents research in assessing the effects between a planar antenna integrated on the solar cell and the photovoltaic cell. A series of experiments were designed to perform assessments for antennas operating from C to X bands. It is concluded that a commercial triple junction space–certified solar cell normally would decrease the gain of the antenna to 2–3 dB and is not affected by the working states of solar cells. The shadow of the antenna casts on solar cells, however, is not significant (less than 2%). The thesis also provides a model of a common space solar cell that helps to explain the gain loss. The model was validated by experimental data, and it was utilized to predict iv a possible custom design of solar cell where with a minimal design modification, it would facilitate less gain loss of the antenna integrated on top. On the array level, the research surveys different high gain antenna array design and then focus on an optimal sub–wavelength reflectarray design. The final antenna array design is a 30 cm by 20 cm, X band (8.475 GHz) reflectarray that shows 94% transparency, 24 dB gain, and higher than 40% aperture efficiency. The design is then prototyped and tested on actual solar panel. The measurement of the reflectarray placed on the solar panel showed a gain of 22.46 dB and an aperture efficiency of 29.3%. While those results are considered excellent, the thesis continues to address the reasons for reduction of the antenna’s performance due to the solar panel, through both theoretical analysis and experiments.

Transparent UWB antennas have been the focus of this PhD research. The use of transparent UWB antennas for stealth and energy harvesting has been the underlying applications that have given impetus to this research. Such transparent antennas being built on materials that are discreet, flexible, conformal, conductive and having the ability to provide good antenna performance on glass to serve as the ‘last mile’ link in subsequent generation communications after 4G have been the basis for this contention. UWB in this regard is able to provide the transmission and reception of high data rates and fast video transmission that is an elementary demand of even a 4G wireless communications system. The integration of UWB antennas with photovoltaic to provide integral energy harvesting solutions that will further enhance the value of the UWB system in terms of cost effectiveness and performance are thus the basis of this work. This work hence starts with the study of a transparent conductive oxide polymer, AgHT and its properties, and culminates in the development of a transparent UWB antenna, which can be integrated with photovoltaic for window glass applications on homes and buildings. Other applications such transparent antennas can find use for like on-body wireless communications in healthcare monitoring was also analysed and presented. The radar absorbing material (RAM) property of the AgHT was investigated and highlighted using CST simulation software, as no measurement facilities were available. The transparent UWB antenna in lieu of the inherent absorbent property of the AgHT material is thus able to exhibit stealth characteristics, a feature that would be much desired in military communications. Introduction of a novel method of connecting the co-axial connector to the feed of the antenna to improve gain and efficiency of transparent polymer based antennas and the development of a UWB antenna that maintains its Omni-directional characteristic instead of becoming directional on an amorphous silicon solar cell are presented as some of the contributions for this research work. Some preliminary analysis on the impact of glass on UWB antennas for video transmission and how to improve transmission is presented. The ability of the conductive part of the antenna radiator to be used as a RF and microwave harvester and how it can further add value to a transparent UWB antenna is presented by way of experimental data. Finally yet importantly, this thesis presents some insight into how transparent antennas may be used in Green Technology Buildings to provide an integrated solution for both wireless communications and energy harvesting as part of the future work. Improvement to the aesthetics of the external appearance of residential buildings through the integration of transparent satellite dish onto solar panels on rooftops is also discussed and illustrated as part of this future work.